Question about Lands Phones

I have no connection,when I pick both receivers up they light up and both say base but no dialing tone

1 Answer

Your Consultant

Level 3:

An expert who has achieved level 3 by getting 1000 points

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

Master:

An expert who has achieved Level 3.
Master
825 Answers

Try picking only one rcvr up

Posted on Sep 05, 2019

5 Related Answers

Anonymous

77 Answers

SOURCE: Sending and receiving problems

Where the telephone line comes in from the wall, make sure that it is plugged in the "line" or "wall" port. There is probably another port call "tel" or "acc". If the line is plugged into that port you will still get a dial tone but you are not connected to the fax's modem. You hope that's it. Ed

Posted on May 17, 2007

Anonymous

15 Answers

SOURCE: No dial tone, clicking sound

It most likely is the LIU (Line Interface Unit). or you might have it plugged in the wrong port on the fax itself. Make sure it's plugged into the LINE plug. If it's the LIU it would be cheaper to replace then calling for service. Unless it's under warranty still (usually 90 days)

Posted on Jan 29, 2008

Anonymous

14 Answers

SOURCE: Dial Tone - Number Dialed does not go through

The problem is possibly the keypad on the phone. Try another phone , preferrably a standard corded phone. If you still cannot break the dial tone, then the problem is with the telephone line (phone company)

Posted on Apr 01, 2008

Anonymous

31 Answers

SOURCE: No dial tone in Clarity C4230 setup

if you can get dial tone with another phone, look into manual for any instructions, usually a toll free number for help. ( BEST ) otherwise take phone back for exchange. may be problem in the board.

Posted on Apr 16, 2009

Anonymous

5 Answers

SOURCE: No dial tone. Base will ring. Handset has no

Check the Battery on the Handset. remove the pwr frm the base unit n connect aft 30 sec. aft this if it still says the same msg, then the handset needs to be replaced.

Posted on Mar 04, 2010

Add Your Answer

Upload

Upload an image from your computer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

Loading...

Include an image. It's worth a thousand words.

prev next

Related Questions:

0 Answers

No dial tone cant make calls

Dec 30, 2013 | Lands Phones

1 Answer

I have 2 problems. 1. The orange message light will not stop flashing no matter what I do. 2. Some how the system was switched from touch tone to dial tone. I can't seem to that switched either.

Resetting the voice message waiting indicator
When you receive a new voice mail message, the new message LED on the top of the handset flashes. In the event your message waiting light gets out of sync with your phone company's
voice messaging system, you can manually reset it back to the "No messages waiting" state.
1. Press and hold FiND on the base for five seconds.
Note: The handsets connected to the base will start to beep, however, keep pressing for five seconds.
2. A beep sounds and the message alert tone is reset.
Changing the dial mode
Your phone can communicate with the telephone network in two different ways: tone dialing or pulse dialing. These days, most base networks use a method called tone dialing, so your phone comes programmed for tone dialing. If your phone company uses pulse dialing, you will need to change your phone's dial mode. If you don't get a dial tone or can't connect to the telephone network, please follow the steps below to modify your phone's settings:
1. Press MENU/SELECT.
2. Select the Global Setup menu, and then the Dial Mode submenu.
3. Scroll to highlight Pulse.
4. Press MENU/SELECT. You will hear a confirmation tone.
If you ever need to change the dial mode back to tone dialing, follow the same procedure, but select Tone in step 3.

Finally for future ease of use, here is a link to the user manual were I copied the above information from:

http://www.uniden.com/content/ebiz/uniden/resources/ownersmanuals/DECT1580-3om.pdf

Jul 21, 2011 | Uniden DECT 6.0 Cordless Phone ID

1 Answer

The phone lights up when put to charge also the red light on the base,, but when the phone line is connected it wont work ..What do u think is the problem?

The battery in the handset could be bad . First I would test that the base unit is recieving dial tone by pressing speaker button on base unit. If there is dial tone then problem is in handset or in base unit communication to handset. Try resetting power to base unit. Check manual for any re-initialization procedure. If the base unit is not receiving dial tone then I would test that the phone line is delivering dial tone to the base unit by connecting a known good phone to the line cord. If the dial tone is not present , problem could be in line cord from outlet, outlet, building wiring, or service provider.

Dec 08, 2010 | Uniden Cordless Phone

1 Answer

I have one phone on the system that when you pick up the hand set you get an error instead of a dial tone to get the dial tone I need to hit the recall button. Another way to get the dial tone is hit...

place that headset in the BASE not one of the stand alone chargers for a few seconds. that should "sync" it with the system.

Aug 20, 2010 | Cell Phones

1 Answer

No dial tone! what do i do??

with your main base plugged in you should have lights on it, this means your getting power, now check if your phone wire is plugged into your base all the way. If you pick up your phone and hit the center button it should light up the phone and read connecting, then give a dial tone. if not i would try another phone in that same wall jack and try. If another phone works fine and all your connections are good try replacing phone cord to base and try it. If still no good check that phone in cradle is hs1. handset no. 1 and try. hope this works

Jan 12, 2010 | Vtech 5.8GHz Cordless Phone with Digital...

1 Answer

Cannot receive calls and dial tone flashing

You have a feature active on your phone it's more than likely a call forward feature which would redirect you calls. The broken dial tone or stutter dial tone is an indicator a feature is active. Contact you system admin for the clear all feature code and the clear all call forwarding codes.

Feb 26, 2009 | Mitel 5220 IP Phone

1 Answer

Dial tone is active as I'm dialing, callers cannot hear me speak

Your phone is broken, the only solution is to replace it. Call Uniden Customer Service and they should be able to help you. 1-800-297-1023. ( I'm serious, there is no way you can fix this problem with out opening the base unit up and replacing a bad transistor)

Feb 24, 2009 | Uniden DECT 6.0 Cordless Telephone...

1 Answer

Pick up receiver and get a dial tone for outgoing w/o pressing 9

I beleive you are referring to a phone which is part of a PBX system or Key-system (sounds more like a Panasonic PBX system). If so, this is a system program that has gone "bonkers". You may need to re-program the automatic outside line dial tone on the system for the specific phone you are referring to.

Jan 28, 2009 | Panasonic KX-T7030 Corded Phone

1 Answer

Phones won't pick up calls...say connecting

HOLD THE HANG UP BUTTON AND THE POUND BUTTON DOWN FOR 5 secons. select base unavailable....yes. then hang it up on the base and it will register to the base. if that doesn't work then unplug the base then plug it back in then put the reciever on the base.

Nov 20, 2007 | Uniden TRU9380-2 Twin Phone

2 Answers

Fax problem

I want to make sure I understand this completely. You get no dial tone from the fax machine when hooked up to VOIP. In the past, was there an audible dial tone from the fax, or did it just dial silently and give you an error if there was no tone? When you said you got a dial tone by connecting a phone to the ext phone port of "the machine" did you mean the fax machine? If you get a dial tone by running a phone through the fax machine, then the line is good. I have used a fax machine over Sunrocket before they went defunct, which used the same technology base as Vonage - so it should work. If you used to get an audible dial tone when using the fax, and no longer do, and you are geting a dial tone on a regular phone that is connected to the ext. port of the fax machine, then the problem has to be in the fax machine itself, not the VOIP. If you can verify that, we can go from there.

Oct 08, 2007 | Brother MultiFunction Center MFC-440CN...