How do it remove the touch pad from kitchenaid khms2056ssss. How does the door come apart?

KitchenAid Appliance Fault Codes - PartSelect

www.partselect.com/JustForFun/Kitchen-Aid-Appliance-Fault-Codes.aspx
Fault codes for a number of KitchenAid appliances, including two and four digit codesfor ... F9 - Oven Door Lock Failure - Check door lock switches and wiring.

You must presume Tech knows what he is talking about , but get 2nd opinion, then you will be sure.

Hello, Christi,
What i would try first is see if perhaps the ribbon cable has come loose from the control panel the touch pad is separate from the control board and its entirely possible that its bad and not the control panel.Also i would surly want to check to door switch as well since they are more common problem than either the touch pad or control board ..to me its sounds like possibly the door switch is the problem since it thinks the door is open and wont allow it to start since the door switch thinks its open .
Please respond if you should need further assistance.
GENE

Hi,

Unplug the oven for few minutes, say 30 minutes and then turn it on.If the problem persists, you need to replace keypad. This is a quite easy repair. You would take the grill off along the top over the door. Once off you should see the screws holding the control panel in place. Remove these screws and remove the control panel. You will now have access to replace the part. Please be aware that the unit stores lethal voltage even when unplugged.

F2 means the touch pad has failed, the manufacturer recommends you replace the touch pad and if this fails to clear the problem replace the control board.The manufacturer recommends this but the problem normally relates to the touch pad. The control board sits just behind the touch pad so is accessible by removing the control panel.

Let me know,if needed further assistance.

Hope i helped you.

Thanks for using ' Fixya ' and have a nice day!!

could be a few things the touch pad display has a ribbon cable that connects to the pcb or control assemble...the touch pad could be bad /// the pcb(main control) has a fuse in it and they often go bad this reuires taken the cosole apart and removing the screws on the inner door to get it off. if the fuse is not bad you have either a bad pcb or touch pad... before doing all this kill power to unit at breaker for at least thirty seconds and then reset...hope this helps

Hi,
This time the problem is not the touch pad...
The self cleaning feature gets things extremely hot and has either burnt up the wiring to the touch pad or has caused the power supply on the main circuit baord to fail...to find out for sure which problem it is the power supply will need to be checked and then the appropriate part changed...

Self Cleaning Oven Problem

heatman101

F2-E0 - Shorted Touch Pad (Keypad) - Check the connection between the touch pad (keypad) and control board (clock) to make sure it is secure.
Select the 'cancel' function and wait 60 seconds.
If error code reappears then replace the touch pad, or touch pad and control board (clock) if all one assembly.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE [email protected]@

Hi,
It sounds like the door interlock is broken.
Have a look for any hooks or latches that may have snapped.
If the door interlock is faulty - do not use this microwave untill a replacement is ordered and fitted.

We have a gas kitchenaid KGST307HBL9 and the touch pad is blank, but we discovered that you can still touch the buttons and it will work. (example touch bake; temperature; start). It will beep when the target temperature is reached.

Just so we don't forget and leave the oven on, we turn the oven light on as our signal. A little work, but not wanting to "fork" out the money at this time to repair.

Also, if you are handy RepairClinic.com has many items and can also answer question. We've used them for several of our appliance repairs.

F2-E0 - Shorted Touch Pad (Keypad) - Check the connection between the touch pad (keypad) and control board (clock) to make sure it is secure.
Select the 'cancel' function and wait 60 seconds.
If error code reappears then replace the touch pad, or touch pad and control board (clock) if all one assembly.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE [email protected]#$