Question about MTX Car Audio & Video

1 Answer

I have a mtx tunder series 942 when you hook it up the red light comes on I have the best wire and have checked everything the amp is old school it does have a fuse on it I have one on my power line pls help!!!!!

Posted by Ct Woodel on

×

Ad

1 Answer

Erik Walters

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 155 Answers

I was having a similar issue. I checked every wire from the battery to stereo to amp, checked the ground, pulled the stereo to double check the wiring was all correct. Everything seemed good so I thought it had to be my battery not putting out enough power. Tested it and it was good. What it turned out to be was the connection from the power cord to the battery. It had a tiny bit of built up corrosion that was making the amp go into protect mode. Cleaned it up and hooked it back up and has been golden since.
The link attached is pretty straight up on what you need to check for different circumstances. I'm guessing it's a low voltage issue. Good luck

Posted on Aug 23, 2019

Ad

5 Related Answers

Anonymous

  • 56 Answers

SOURCE: Red light on Amplifier

if your amplifier has the internal Kicker card dealie "little computer card on the side that you can change out crossover settings and such," Turn off the vehicle, remove this device and make sure the contacts on the card are clean and free from black soot (showing a spark). clean the contacts with a pencil eraser or something hard but soft... and put the little card back in place, start the car again and see if that helps, I used to lose one speaker every once in a while with the same amp. I ended up replacing the module with a different one from my dealer and it worked fine (still does and it's been in my car 6 years). Check that little module. if this doesnt work, while the car is running and the music is "playing" wiggle the card and see if it works sometimes and not others. Likely is the little module.

Posted on Aug 15, 2007

Ad

Paul Teichmann

  • 103 Answers

SOURCE: sony explode amp for my car

Try disconnecting everything but the power connections. If the protection light still comes on, then there's a problem in the amp. If it goes out, then there's a problem elsewhere. In that case, hook up one speaker cable at a time and power on. If the protection light comes on, then either that speaker is bad, or you've got too many speakers connected to that one amp output. Too many speakers connected together can cause an overload and trigger the protection circuitry, or worse, blow out something out.

Hope this helps, and please rate my advice.
Thank you, and good luck!!

Posted on Feb 05, 2008

Anonymous

  • 631 Answers

SOURCE: mtx 1501d no sound

There are a number of things that can cause it to act as you described. Have you pulled the covers off of it yet to see if you can see any problems?

If you do, disconnect power from it and don't touch ANYTHING on the board when ANY of the 3 LEDs (2 are not visible from the outside) are lit.

Posted on Aug 19, 2008

jason

  • 905 Answers

SOURCE: Amp won't turn on

disconnect audio inputs and outputs and see if one of those are causing it , if it still does it with all audio inputs and outputs disconnected then there is a problem with the power amp

Posted on Oct 08, 2008

Anonymous

  • 103 Answers

SOURCE: MTX Terminator Amp...Red light comes on when it should be green.

its just a power light to let you know its on

Posted on Jul 25, 2009

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I hook up 4 10 inch mtx old school?


you can put them in one box you will need a good port hole if you do.How to build subwoofer box

this link is on how to hook up speakers Subwoofer wiring diagrams \

good luck

Aug 11, 2015 | MTX Car Audio & Video

1 Answer

I just bought 2 12 inch mtx thunder tc512 to replace my old school mtx blue thunders, everything worked great, but when i hooked up the new 12s i get nothing, zero, zip, nadda, there is nothing wrong


use a d cell battery and touch + of speaker to + of battery and hold it by doin the same with the -'s too if move they work if not there junk

Sep 09, 2012 | MTX Car Audio & Video

2 Answers

Tc 8001 red light


on some amps there is a duel light. red and green usually. red means it is in protect mode or you didn't hook up your remote wire. if in protect mode, it could mean a number of things. did you hook it up with speakers and everything?

Mar 01, 2012 | MTX Thunder® TC8001 Car Amp

1 Answer

I recently purchased the mtx terminator amplified bass system and wired everything in, but the amp seems to not be working, i checked the power and the wires going in are a good circut but none of the...


If none of the lights are coming on for the amp then the amp is not getting power and/or ground. Check the connections. Check the fuses. Or the amp is no good.

May 05, 2011 | MTX Car Audio & Video

1 Answer

MTX Thunder 81001 wont push subs


first of all you should check the minimal impedance your amp handles , if is class d it should handle between 1-2 ohms total impedance in a mono conection , meaning whatever quantity of subs you have hooked to your amplifier,their total impedance should the minimum the amp handles that way all the power from your amplifier will be used.

Jan 23, 2010 | MTX Thunder 81000D Car Audio Amplifier

1 Answer

Green light (protection mode) on, NO red light (ready)


double check your wires aren't shorting out or power or remote wires aren't grounding. check if speakers are blown with nine volt battery

Sep 05, 2009 | Kenwood Car Audio & Video

1 Answer

MTX thunder 304 4ch red amp light comes on but no audio have triple checked all connections and they seem alright


if the lights on and there is no sound it's either a cd player issue or your rca issue or the inputs for rca's on the amp are no good. or you have your subs wired at a wrong load to your amp and it is in a constant protection to avoid burning up.

Jun 09, 2009 | Car Audio & Video

2 Answers

Mtx 1501d no sound


There are a number of things that can cause it to act as you described. Have you pulled the covers off of it yet to see if you can see any problems?

If you do, disconnect power from it and don't touch ANYTHING on the board when ANY of the 3 LEDs (2 are not visible from the outside) are lit.

Aug 19, 2008 | MTX Thunder 1501D Car Audio Amplifier

1 Answer

HELLO CAN SOME BODY TELL ME HOW TO HOOK UP MY SYSTEM RIGHT I HAVE 2 AUDIOFONICS ADF-272 1200 WATTS AND A MTX 4501 CLASS D MONO BLOCK AND A MTX 801D KIND OF OLD SCHOOL IS LIKE 4 YEARS OLD AND HOW TO series...


http://www.rockfordfosgate.com/rftech/woofer_wizard.asp?submitted=true&woofer_qty=1&woofer_imp=4
HERE IS HOW YOU HOOK UP 1 SPEAKER TO 1 CHANNELM DO THE SAM E TO THE OTHER CHANNEL. MAKE SURE AMP IS IN MONO MODE,YOU DONT WANT TO PLAY UR SUBS IN STEREO.AS FAR AS THE BOX DEPENDS ON VEHICLE AND HOW MUCN SPACE YOU HAVE .TELL WAT MODEL CAR AND ILL ET BACK TO YOU. I NEED A FIXYA RATING PLEASE

Feb 10, 2008 | Audiofonics ADF-272 Car Speaker

Not finding what you are looking for?
Car Audio & Video Logo

Related Topics:

131 people viewed this question

Ask a Question

Usually answered in minutes!

Top MTX Car Audio & Video Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

The Knight
The Knight

Level 3 Expert

76416 Answers

Steve F

Level 3 Expert

1360 Answers

Are you a MTX Car Audio and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...