Question about Konica Minolta Office Equipment & Supplies

1 Answer

HOW TO RESOLVE CODE C-2221 KONICA MINOLTA BIZHUB C5500

Posted by AKAYE TETEVI AMEVI... on

Ad

1 Answer

spensivan34546

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

1.The terminal for the first transfer pressure/release sensor is not connected properly.
Reconnect the terminal.
2.Failed PS15 (p/n 08AA 8551 2).
Test photosensor, PS15, in the I/O State Confirmation Mode, 48-0HIGH = home position or LOW = Other than home position by activating M19 (p/n 08AA
8003 0) transfer pressure/release motor, 48-0, 48-1, 48-2, or 48-3. Replace thephotosensor or motor as needed.
3. Possiblefailed Transfer/Pressure Release motor (M19).
Check the operation of the motor(p/n 08AA 8003 0) in the I/O State confirmation mode for proper operation with code 48-0; this should rotate the motor
constantly. Replace motorif needed.
Also check for possibleopen ICP fuses, ICP3 (5V DC)and ICP4 (24V DC) on the AC drive board (p/n A03U H520 01). Replace the drive board as necessary.
SPECIAL NOTE : Solution contribution by KMBT (Japan) and Freddie Burnham, Production Print/SSD

Posted on Aug 19, 2019

Ad

5 Related Answers

Anonymous

  • 2 Answers

SOURCE: konica minolta bizhub 350

• The Fusing Roller Sub Thermistor does not
detect the required temperature within 30 sec.
after a warm-up cycle has begun; therefore, the
copier does not complete the warm-up cycle.
• The temperature of the Fusing Rollers does not
reach the required level even after the set period
of time has elapsed during a warm-up cycle.
1
Check that the H1[ fuser lamp] comes on when the Main Power
Switch is set to ON, and correct or replace as necessary.
- -
2
Check that the H2 comes on when the Main Power
Switch is set to ON, and correct or replace as necessary.
- -
3
Check the installation of the TH1 and the TH2, and
correct or clean as necessary.
- -
4
Check the operation of the TH1.
Remove CN80 (4P), and then check that the resistance
across CN80-2 and -3 on the Thermistor is
infinity.
- -
5
Check the operation of the TH2.
Remove CN81 (4P), and then check that the resistance
across CN81-2 and -3 on the Thermistor is
infinity.
- -
6
Check the continuity of the H1.
Correct or replace as necessary.
- -
7
Check the continuity of the H2.
Correct or replace as necessary.
- -
8 Change PU1 - -
9 Change PWB-A

Posted on Nov 19, 2007

Ad

Anonymous

  • 589 Answers

SOURCE: copier malfunction

Code C0F36 is a low toner density error on the black developing unit.

Was it asking for black toner before this code appeared?

Posted on Feb 10, 2008

herminio_hal

Herminio Halili, Jr.

  • 210 Answers

SOURCE: Bizhub Konica Minolta - Error Code C1183

First check the alignment front and rear of the finisher, check the finisher exit guide rollers if the paper is exiting properly, open both rear and the front cover and check the lower gears attach is the up/down drive belt. that lower gear one might be broken by the pin slot.

Posted on Jul 09, 2009

Anonymous

  • 3 Answers

SOURCE: c350 malfunction code c-0501

After replacing the fuser unit, if you got a c0501 code you must open the front door where the toner is. On the right side (hinge side) next to the black toner and drum unit there is a plastic pannel/cover. In the lower portion of that pannel there is a hole where a trouble reset switch is loacted. With a flashlight you may be able to see it. You are ment to use a thin screw driver or the like to push the button. You do this while the machein is on and desplaying the code. As soon as you press the button the copier will clear the code and start warming up. Thats it! If you are un certin of the button placement you can take out three screws from the pannel and loosen one screw from the pannel above it and and pull the pannel off the unit. You will see the board and it is the button on the (left), as there are two of them. Tho you only have access to the one thru the cover.

Posted on Oct 18, 2009

Anonymous

  • 1 Answer

SOURCE: Konica Minolta Bizhub c350 error code c-0510

I have this code

C0510 Upper fusing roller abnormally low temp

how can I replace the thermistor in the fuser


Posted on Dec 30, 2009

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Konica minolta bizhub c 7000 error code c 2221 how to fix?


Any one of the following might cause that code,
AC drive board (ACDB)
• Printer control board
(PRCB)
• 1st transfer pressure
release motor (M19)
• 1st transfer HP sensor
(PS15

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

May 06, 2017 | Konica Minolta Office Equipment & Supplies

1 Answer

Konica minolta bizhub c450 error code c- d370


I have minolta c450 show error c d370... how can I solve this problem... plz reply me with solution.

May 14, 2013 | Konica Minolta Bizhub C 353, Bizhub...

1 Answer

Konica minolta C252 error code C9401


my machine konica minolta C252 is giving the code 9401 how should I resolve and what is

Jan 30, 2012 | Konica Minolta bizhub 250 All-In-One Laser...

2 Answers

Konica Minolta bizhub C250


i think that your fax is not set up right, or maybe the machine is missing admin and machine e-mail address, that can cause too this problem.

Dec 12, 2007 | Konica Minolta bizhub C250 All-In-One...

Not finding what you are looking for?
Office Equipment & Supplies Logo

Related Topics:

187 people viewed this question

Ask a Question

Usually answered in minutes!

Top Konica Minolta Office Equipment & Supplies Experts

Norman  J Weimar Jr
Norman J Weimar Jr

Level 3 Expert

6960 Answers

carpediemweb

Level 1 Expert

54 Answers

George Mclaughlin

Level 2 Expert

369 Answers

Are you a Konica Minolta Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...