I have a LG Top load fuzzy logic washing machine. Machine takes wash options correctly and takes water but when it just to start the washing it shows DE problem blinking. What I came to know from the manual it means the door/lid is open. However the lid is closed. What should i do to rectify it. Is it just a door problem or a circuit probelm. Any one can pls help me out.
I have the same problem. please let me know if yours got fixed
Hi, there is a small magnet in the door. please check if the door seems broken, it is a very small break so check properly, if there is no magnet, it will continue to show de though the door is closed. if the magnet is lost, replace it and put super so it does not come out again. don't closed door while super glue is still not dry.
thank you very much for your brilliant solution!!!!!
Thank you too! it's friday night so I can't go out and buy a magnet clip thingy but I can sit on the lid and get my work clothes ready for tomorrow. :)
Hi there, i've got the exactly same problem but i've checked the magnet. it's still there, no brokens. i took the magnet out, tested it on a metal object and it's still sticking. i've even checked the surroundings of the door to make sure that nothing is blocking, stuck or attached. what could be the other cause and solutions for this problem. Thank you in advance
Please where can one buy the magnet ?
Please where can one buy the magnet ?
Hi. I am facing the same issues. Bypass the magnet. Unscrew the panel board from the front face and you can see an small fuse at the opposite of the magnet located at the lid. Loop it end to end. ATTN, IF YOU DO SO, THE MACHINE WON'T TURN OFF EVEN IF THE LID IS OPEN.
×
Here are the photos of that area where the magnet is located...
Thanks a ton...It really worked for me ..Kavita..:)
Thanks
I managed to fix mine. I removed the magnet from its housing. And removed the plastic cover with the buttons it. I placed the magnet on the sensor resting it there and it works now.
Picture needed. Where is the sensor exactly
×
Hi there, i've got the exactly same problem but i've checked the magnet.
it's still there, no brokens. i took the magnet out, tested it on a metal object and it's still sticking. i've even checked the surroundings of the door to make sure that nothing is blocking, stuck or attached.
what could be the other cause and solutions for this problem.
Thank you in advance
Solved my problem /i fix magnet with glue and error DE disappear
thank to fixya for proper advise
Where on the lid is the magnet meant to be? I can't find where it is supposed to be.
hi kaitlyn. did you find out where the magnet is meant to be? I have the same problem here. it's driving me nuts.
Hi there, i've got the exactly same problem but i've checked the magnet. it's still there, no brokens. i took the magnet out, tested it on a metal object and it's still sticking. i've even checked the surroundings of the door to make sure that nothing is blocking, stuck or attached. what could be the other cause and solutions for this problem. Thank you in advance
×
The magnet is located at the very front of the door in the middle of the lid about were the time display is , its a little rectangle area
Hi there, i've got the exactly same problem but i've checked the magnet. it's still there, no brokens. i took the magnet out, tested it on a metal object and it's still sticking. i've even checked the surroundings of the door to make sure that nothing is blocking, stuck or attached. what could be the other cause and solutions for this problem. Thank you in advance
×
Hello i have Fuzzy logic Lg everythng is Correct but still not spining can anybody help me out plz
If the magnet is in place and the problem persists then the reed switch needs to be replaced.
Hi all,
Thank you very much. I just fixed my machine with the help of above solution.
Regards
Dushyantha
13,437 views
Usually answered in minutes!
×