Question about Garden

2 Answers

I have an old Toro proline 52 inch commercial walk behind 18hp kohler and I don't know how to put the transmission belt on right.

Posted by jim_cox13 on

Ad

2 Answers

Roger Geer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 78 Answers

Simple rule. V of the belt goes in V pulleys
The back of the belt goes on flat or idler pulleys .
It may take several tries but I am sure you can figure it out.

Posted on Oct 28, 2009

Ad

Anonymous

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

With ur dikki pemole

Posted on Jul 02, 2010

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Location of switch for brake pedal on 18hp Toro lawnmower that prevents cranking


most of these switches areblocated under the mower along the brake pedal shaft

Dec 04, 2017 | Toro Garden

1 Answer

Toro proline 120 52 inch runs good until pto is turned on engine then shuts off


sounds like a safety switch is bad check the one on the seat first

Jul 05, 2012 | Garden

1 Answer

Proline toro commercial 32 inch won't run


try starting fluid that will see if its a fuel problem then check for spark

Apr 19, 2012 | Toro Garden

1 Answer

Toro 52 inch walk behind blades won't engage


if it has a electric clutch check for power to the clutch if no check the safety switches

Apr 10, 2012 | Toro 52" Cut Wide Area Walk Behind Lawn...

4 Answers

I have a Toro Proline walk behind . Problems with the self propel


I suspect the drive belt, not the Hydro. Especially if the drive belt was never replaced. The belts are known to stretch and wear out over time. It's a cheap part.

Jun 04, 2010 | Toro Lawn Mower With Toro Power Tools

2 Answers

Toro 20073 self propeled, walk behind mower-how to replace belt ?


Wait until the mower cools off

1. Remove the drive belt cover from the top of the mower
2. Tip the mower up, being careful to not go too far or the oil and fuels may spill out
3. Remove the mower blade - as I recall the bolt is 5/8" (could be 9/16") You will have to hold the blade from turning (if you have impact tools, this will be much easier)
4. Remove the blade
5. Pull the pulley out or off and remove the belt - be careful to not lose the crankshaft "woodruff" key - it's the little piece of half/moon shaped metal that keeps the pulley from spinning on the crankshaft.
6. Reverse the steps to reinstall

You MUST make sure the blade is tight when you reinstall it. Also, the blade usually fits over a couple of pins - make sure they are lined up properly and the blade is installed right-side up.

Mar 16, 2009 | Toro Lawn Mower With Toro Power Tools

Not finding what you are looking for?
Garden Logo

Related Topics:

681 people viewed this question

Ask a Question

Usually answered in minutes!

Top Garden Experts

Dennis Key
Dennis Key

Level 3 Expert

2481 Answers

john h

Level 3 Expert

23424 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Are you a Garden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...