GB5108 picture is collapsed to a blue line in the center

What can be the problem and is there a service manual available?

1 Answer

helper 1

Level 1:

An expert who has achieved level 1.
Contributor
1 Answer

Go to Trinixsoft.com for complete manual. Cost 4.99 for download or 9.99 for shipped cd. I kinda have same problem but my exits with 3 red colors in bowtie form. I think mine is the TDA8351 or vertical control IC. Hope this helps.

Posted on Dec 19, 2007

Add Your Answer

Upload

Upload an image from your computer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

Loading...

Include an image. It's worth a thousand words.

prev next

Related Questions:

0helpful

1answer

Manual

All service manuals for these are online and only available to authorized service centers.

At your own risk: with set on in cable band: 062597 status will take you directly to convergence tech menu--be careful what you do and if not sure do not go to the menu after and select save.

Read full answer

May 04, 2012 • Philips Televison & Video

0helpful

2answers

No picture, Horizontal line center of screen

Can be a case of vertical collapse. If this is the case, then the vertical oscillator and/or the vertical driver circuit are faulty. .

You can take you problem directly to zenith. They have a customer service post available here

Read full answer

Mar 30, 2008 • Zenith Z32H41D TV

0helpful

1answer

I have a black line acrossthe center of my apex gb5108 tv. does anyone know if it is worth fixing?

hi
it should be changed just
if any body want to repair, it may be to expand the problem

Read full answer

Jun 02, 2010 • Apex Digital GB5108 51" Rear Projection...

0helpful

1answer

Blue wave across screen

Just click below for convergence repair kit;

http://servicemanuals.vstore.ca/

Double images and colors are blurry .Blue,red and yellow wave coming up from the bottom of the screen on the lower left symptom is for busted convergence IC,you must replaced this IC in order that will works better again.STK 392-xxx ICs and it's associated resistor,this resistor automatically change value,can caused truoble even though you change the ICs.If you bring this to a service center they cost you $600 to $700,but if you buy the repair kit you can save more,don't wory it is very easy because there is intallation guide including in the repair kit. Feel free to ask whatever the result... click the link for sample picture guide step by step installation;

Hope this may help;

Regards,
VOTIT

Read full answer

Sep 08, 2008 • Apex Digital GB5108 51" Rear Projection...

0helpful

1answer

I have a apex GB5108 tv, the picture has become a red yellow and blue horizontal line in the middle of the tv. is it fixable

Thats vertical deflection failure . Check the solder on the vertical output IC and the Yoke plugs. If that doesnt help you may need a new Vertical IC

Read full answer

Jul 01, 2008 • Apex Digital Televison & Video

0helpful

1answer

Apex gb5108

'I to am getting only wavy blue lines, no sound, doesn't even show channel indicators. TV was off for 4 days, came home turned it on and ten minutes later this screen appeared, it wont even show the menu screen, different channels or video inputs no sound either.

Read full answer

Jun 21, 2008 • Apex Digital GB5108 51" Rear Projection...

0helpful

1answer

Blue screen , horizental retrace line , no picture , audio ok

Try replacing the STK- chips

Read full answer

Dec 16, 2007 • Apex Digital GB5108 51" Rear Projection...

0helpful

1answer

Bright line coming in center of screen

Hi Shailendrar , your problem sounds like vertical collapse , the whole picture has collapsed into a thin , very bright centre line ? maybe the result of dry solder joints , does banging on the side of the tv temporarily fix ? if so , the circuit board requires inspection for bad solder joints . Alternately the vertical chip/transistor may be blown , replace as required. Cheers T

Read full answer

Dec 05, 2007 • Philips 19PR19 19" TV

2helpful

3answers

SOUND NO PICTURE ONLY RAINBOW

I just fixed this problem on my neighbor TV. I don't have a manual or schematic, and didn't pay any attention to the reference designators, so I will just have to describe it. The problem was a bad solder joint. Visible thermal fatigue. Looking at the main board, (didn't even need to slide the cassis out). There is a small, narrow, vertical board in the center, adjacent to the yoke connectors with a funny looking little transformer on the very top. Check the connections on that.
-John

Read full answer

Dec 15, 2006 • Apex Digital GB5108 51" Rear Projection...

1helpful

7answers

Apex GB5108 Convergence and screen issues

TWO INLINE FUSES ON THE POWER SUPPLIE BOARD, ALSO THERE TWO CAP [email protected] AND A [email protected] THESE WILL LEAK UNDER STRESS. JOHN PATE WITH JOHN'S QUICK REPAIR.

Read full answer

Dec 20, 2006 • Apex Digital GB5108 51" Rear Projection...