I assume your not using a pure sine wave inverter. A lot of electronic devices won't work on a lower cost inverter (modified sine wave) that has a square sine wave, either invest in a true sine wave inverter or don't run sensitive electronic equipment, I'm somewhat surprised you didn't damage the circuit board in the microwave...Below is a link of a inverter that would work if you want to spend the money for one.
2500W 5000 Watt Power Inverter Pure Sine Wave 12V dc 110V 120V ac LCD...

Feb 05, 2018 | Electronics - Others

1 Answer

Kenmore AC window unit model 253 70151 cuts on and off.

Circuit board could be the problem but compressor needs to be checked and there might be a loose electric connection or high voltage causing the ac to trip

Apr 04, 2014 | Heating & Cooling

1 Answer

My clipper will not cut my pet's hair. It seems to run fine. The blade is not dull as it cuts my hair. If I take it apart and reassemble it, it will sometimes cut for just a second and then it just...

See if the hair is clogging somewhere, do you have user guide? Try clippers for dogs or go to the groomers.

Good Luck
Diana

Aug 31, 2011 | Oster Golden A5 2-Speed Universal Motor...

2 Answers

Why my andis outliner not cutting

Hello,
Try cleaning the head cutter below the main stem. Remove screws and clean old hairs in there, also lubricate.
Thanks

Jun 13, 2011 | Andis 04603 Hair Trimmer

1 Answer

How do you turn it off

Around the back the flash has an on/off button that glows green to show power on, a ready light that glows orange when the ringflash is charged this doubles up as a test button. There’s also a 2.5mm sync socket for the flash sync cable and an exposure scale.

On the front is an auto manual switch. If you set to auto the sensor on the front of the flash cuts the power so it’s correct for the auto aperture that’s been selected. You determine which aperture to use via the scale on the back.

Apr 06, 2009 | Vivitar 5000 Ring Light Flash

1 Answer

I bought a 19 piece and i can't cut my hair

It soulds like the blades are too far back. There is an adjustmebt piece to the right or left of the blade that is about 1 1/2-2" long and it slides forward and backwards.
Ths will adjust the blade depth. It sounds like the blades may be set too far back to cut your hair, this has to bring the 2 blades together so you have much less free edge on one side, so what you do is slide ths blade by adjusting the handle and bring the blades to just where one side is slightly shorter than the other less than 1 cm. Then make sure the guard is off and slde the adjustment head is set and then try it agan. Unusually it is the problem if it does not cut or the blades have come loose. Hope that helps.

Apr 05, 2009 | Conair HCT-426 Hair Trimmer

1 Answer

I lost my job, and am in need of dog haircut instructions.

I had a dog with hair. I couldn't afford to take her to the groomers, so I bought an Oster Animal Hair clippers and just buzzed off the hair myself. They have little attachments to go on so they don't cut so short. If you mess up, the hair grows out. My kids used to laugh at some of the hair cuts. I had to train Buttons to hold her head very still when I cut around her eyes. That part scared me, but she did hold still. Some times I had to let her run around awhile and come back to the hair cut in 10 minutes. I also had to train her to lay on her back for the tummy & chest trim. She never did like the toenail trim though. I had to sit on her to get it done. Luckily she was only 13 lbs. I did her hair twice a year and sometimes 3 times. I used the scissors on her feet too. Check at Fleet Farm, Target, or Sally's Beauty Supply for cutting tools.

Mar 29, 2009 | Google Computers & Internet

1 Answer

Coleman 5000 generater-no AC output

Try replacing the capacitor. You can buy it from http://www.jackssmallengines.com/do_it_home.html. When you pull off the power end of the generator look at the diodes also. If they look toasted replace them as well

Jan 09, 2009 | Coleman Powermate Powermate 5000W...

1 Answer

Oster A5 single speed clipper not cutting

not usually we will not sharpen blades that are worn out as we cannot charge for something that does not cut!
make sure your blade is connecting with the drive of your clipper they might need an extra push depending if the blade has been adjusted.

Jul 17, 2008 | Oster 76974-160 Hair Trimmer