Question about Mitsubishi WD-57732 Projection Television

1 Answer

Wd 57732 won't turn on, power/timer light blinks

Mitsubishi wd-57732 won't turn on, power/timer light blinks until bulb led comes on. can't run diagnostics code by pressing input and menu. tv has brand new bulb in it, but doesnt fix the problem

Posted by patrick0621 on

  • Anonymous Mar 16, 2014

    i have a mitsubishi wd-65735. It just shut off out of nowhere and did not turn back on. after about a month i plugged it back in and it turns on but a blue screen. The green timer light stays on while tv is turned on. when i press input, i can see the xbox, cable, dvd options but when i use the hdmi input for cable it does not play anything or when i switch to xbox input nothing happens, just stays in the blue screen....Finally when I shut it off last....the bulb light blinked a few ties in green and it powered off????

×

Ad

1 Answer

Julio Hernandez

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 616 Answers

Probably something related to the FMT board. will need shop service.

Posted on Aug 30, 2009

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Blinking Green Light on Mitsubishi DLP 52525


the circut that detects the bulb has been also failing in these sets
and the conversion chip that controls the picture , and the transformers are not putting out the full power they are supposed to.
this set will need to be tested to determine the exact cause or causes

Oct 18, 2008 | Mitsubishi WD-52525 52" Rear Projection...

1 Answer

Timer light blinks constantly


Hi,
Is it Mitsubishi WD-52628 TV? please confirm model number.
Unplug TV from AC outlet for couple of minutes, replug back in, turn power ON and check, still same problem?
Lets read error code in TV, press Device and Menu buttons on front of TV at same time for 6 seconds that will activate error code read process. Led will flash in 2 sequence with half second pause. count it and let me know the error code to proceed.
Thanks.

Jun 29, 2009 | Mitsubishi WD-52628 52" Projection HDTV

4 Answers

Mitsubishi WD-62525 timer light keeps flashing after lamp replace


There is a tiny reset button to the left of the timer light. Press with a pin or something small, wait 60 seconds. Viola!

Dec 29, 2008 | Mitsubishi WD-62525 62" Rear Projection...

1 Answer

Mitsubishi WD-52525, replaced bulb but still not working


SYMPTOM: Power LED does not stop blinking after plug in.
CURE: Check C81A2, C81A3, C81B3 and C81B4 (1000 uFD, 16V, 105C) on the DM PCB.
Check C8F19, C8F21, C8F22 and C8F27 (1000 uFD, 16V, 105C) on the FMT PCB.
If any are bad, replace all of them with part # 181P734030 (680 uFD, 16V, 105C).
this is what we at the shop check first. it is quite common. on the power supply board look for swelled up capacitors

Dec 19, 2008 | Mitsubishi WD-52525 52" Rear Projection...

1 Answer

Replaced bulb in Mitsubishi WD-52525 and it still does not work


Press the input/device button and the menu button at the same time. Green LED will blink a two digit code blink 1st digit short pause blink 2nd digit longer pause and repeat. Any number of problems can cause this same symptom.

If the red LED your refering to is the Status LED and not the Lamp LED then you have big problems. A red Status LED indicates no communication from the Format board to the DMD board (light engine). 1/2 the time caps on the format board itself the other 1/2 must send entire electronics package to Mitsubishi.

Dec 19, 2008 | Mitsubishi WD-52525 52" Rear Projection...

1 Answer

Dead lamp


The sensor is located on or near the lamp compartment on the back side. If your lamp keeps blowing it may be the lamp cooling fan not working. However are you sure the lamp is blowing? Press menu and device on the front control panel both in together for 5 seconds and see if the led blinks a two digit code, then let me know the code. Please respond to this same post.

Jul 08, 2008 | Mitsubishi WD-57732 Projection Television

1 Answer

Trouble turning on


Try pushing the Imput and Menu buttons in together on the set and hold for 5 minutes and see if it blinks out a two digit code. Then let me know. Also these sets have a tendency to have some faulty capacitors on the DM board. Hope this helps youout.

Jan 06, 2008 | Mitsubishi WD-57732 Projection Television

Not finding what you are looking for?
Mitsubishi WD-57732 Projection Television Logo

779 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Televison & Video Experts

matt martin
matt martin

Level 3 Expert

1258 Answers

The Knight
The Knight

Level 3 Expert

76407 Answers

Ekse

Level 3 Expert

13434 Answers

Are you a Mitsubishi Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...