I have the same kind of problem. I have the programming code, but when I enter it, after entering the 4 th digit the lock blinks an error thinking I entered an incorrect user code?? So I think I might have to clear the memory and start over but, can't find this info on the Schlage website. Schlage instruction video here: http://consumer.schlage.com/customerservice/videos/FE595_Programming.MPG This is a VERY long download, good video....BUT it says you have to input the six digit programming code before you can do anything. When entering this code, my lock thinks I'm entering a user code and an error blinks. Any help a plus.

Question 1

10helpful

2answers

I have a Defiant Electronic deadbolt from home Depot. model G1X2D01. ive lost the manual and i need to delete some old codes from it.

Snap off the back cover (opposite where you punch the numbers) by pinching the sides and pulling off. Do not press a pen or anything into the small light, you do not need too. Just pinch and yank off cover. You will see a small light and beside it is a small SET button by the batteries, it is labelled.. Press this Set button for 2 seconds. The red LED will light on the front code side and beep twice to indicate you are in programming mode. Enter your current code that you want to change (factory set is 12345) and then press the button that looks like a little lock on the keypad. Enter the digits "10" and press the lock button again. Enter the new code (must be six digits) and then press the lock button again. The red light should go on continously for 10 seconds. The code should be effective.
Note: if you have problems like we did, you can also remove one battery and press the "set" button simulataneously when you reinsert the battery. This resets the factory code of 12345. Then you can start over. For some reason our old code was only 4 digits, but it would not let us reprogram a 4 digit code. It didn't work until we did a 6 digit new code.

Apr 15, 2012 • Locks & Locksmithing

1helpful

1answer

I need the tv code number to put into my Jensen Universal remote control for a Panasonic TV on cable, TV Model# CT-27S18S. I also need to know how to program these numbers into the Jensen remote Remote...

the panasonic numbers are one of the following

0051, 0250, 0055and to program it you need to do

Turn on the component that you want to set up.
Press and release the component key you would like to configure. The red LED will blink once.
Press and hold the "Setup" key until the red LED blinks twice, then release.
Enter the first 4-digit code number for the device you are trying to program. The LED will blink one on each digit entered, except for the last digit where it will blink twice to confirm that a valid code has been programmed.
Now test the code by pressing the "Power" key. If the component turns off, you've got the right code. Follow the same instructions to set up your other components. If the component doesn't turn off, return to step 3 and use the next 4-digit code listed.

Mar 16, 2011 • Panasonic (TH-50PZ700U) Television

2helpful

1answer

How do I play regional dvd's that the player is not tuned to. I have been trying to find a code but I am struggling. Can you help me?

Hi
You need to follow these instructions.

To unlock the Region Code on a Panasonic DMR EZ48 using a One for All - URC 7040

1. Switch on the player (make sure the drive select is DVD).
2. Select DVD on the URC.
3. Hold the magic button on the URC until the DVD button on the URC blinks twice
4. Enter device code 0490 on the URC, (DVD button blinks twice), URC takes control of the Player.

Point the URC at the Player and program the URC buttons using the following procedure:

1. Hold magic button until the DVD button on the URC blinks twice
2. Press 994 (DVD button blinks twice)
3. Briefly press magic.
4. Enter 4 digit code 1911 (DVD button on URC blinks twice)
5. Repeat steps 1, 2 & 3
6. Enter 4 digit code 1202 (DVD button on URC blinks twice)
7. Repeat steps 1, 2 & 3
8. Enter 4 digit code 0653 (DVD button on URC blinks twice)
9. Repeat steps 1, 2 & 3
10. Enter 4 digit code 1804 (DVD button on URC blinks twice)
11. Repeat steps 1, 2 & 3
12. Enter 4 digit code 1435 (DVD button on URC blinks twice)
13. Repeat steps 1, 2 & 3
14. Enter 4 digit code 1556 (DVD button on URC blinks twice)
15. Repeat steps 1, 2 & 3
16. Enter 4 digit code 1227 (DVD button on URC blinks twice)
17. Repeat steps 1, 2 & 3
18. Enter 4 digit code 1178 (DVD button on URC blinks twice)
19. Repeat steps 1, 2 & 3
20. Enter 4 digit code 1299 (DVD button on URC blinks twice)
21. Repeat steps 1, 2 & 3
22. Enter 4 digit code 1230 (DVD button on URC blinks twice)

23. Press the One For All URC buttons in the following sequence

1, 2, 3, 4, 5, 6, 7, 8, 9, THEN hold down 0 until "HELLO" appears in the display;

After about 1 minute the Player comes back to life as Multi Region.

--

-

Please dont forget to vote if you liked my answer

thanks

------

Feb 13, 2011 • Panasonic DMR-EZ48 DVD Recorder

0helpful

1answer

Does not overwrite old codes, just keeps accepting new ones. How can I clear all existing codes?

First, I fix this problem after an hour of try.

I conclude that this dorr lock is better that is appear. Is not a 2 codes door lock, it's a 3 codes one.. and the problem you have is the third code not reset. You can put the same code in each third emplacement. you have just to press the program button 3 time for the third code...

I determinate that I put the third code by error the was i program it the firs time.

;-)

I guide you...

To program the first code, press the reset button once, then enter your 4-8 digit code on the exterior keypad, then immediately press the middle lock button on the exterior keypad. You will hear a beep. This signals that your code has been accepted.
To program the second code, press the reset button twice , then enter your 4-8 digit code on the exterior keypad, then immediately press the middle lock button on the exterior keypad. You will hear a beep. This signals that your code has been accepted.
To program the third code, press the reset button 3 time, then enter your 4-8 digit code on the exterior keypad, then immediately press the middle lock button on the exterior keypad. You will hear a beep. This signals that your code has been accepted.

Jan 27, 2011 • Weiser Lock POWERBOLT ELEC DEADBOLT

0helpful

1answer

Just put new batterys in safe . but safe will not stop bleeping what is the problem

Please follow these steps
Programming a user code
There are two ways to program a user code.
A 1. Press the Program key.
2. Enter the Factory Code. The green LED remains ON
while you enter the 5-digit user code of your choice.
After 5 digits are entered the green LED turns OFF.
(To enter a new User Code, repeat these steps.)
B 1. Press the red button inside the safe. The lock will
beep and the green LED will come on.
2. Enter a 5-digit user code.
(To enter a new User Code, repeat these steps.)
Keep your new user code secure.
For your records, please copy it here:
____ ____ ____ ____ ____
Programming a password
1. Press the Program key.
2. Press it a second time.
3. Enter your 5-digit User Code. The green LED remains ON.
4. Enter the 5-digit Password of your choice (any combination
except 00000.) After 5 digits are entered, the green LED
turns OFF.
(To enter a new Password, repeat these steps. To erase the
Password, press Program twice, enter your User Code and then
enter 00000.)

Battery replacement
Below When old batteries are removed for replacement, your Password will be voided; only Factory and User Codes will work. To
reestablish your Password, follow the directions above under
Programming a Password.
Key override
If your electronic lock fails or you do not have any codes
available, you may use a key override to access this unit.
1. Remove the battery cover, disconnect and remove the
battery holder.
2. Insert the skeleton key (second set of keys provided)
into the key hole inside the opening for the battery.
3. Turn the key to the right.
4. Turn the four bit key to the right.
5. Open the door.
Signals
Your electronic-lock safe communicates by means of several
audio/visual signals.
Red (Error) LED + three beeps indicates
one of the following:
1. You have pressed Program key out of sequence
2. You have entered an invalid code or password.
3. You have let 5 seconds or more elapse between key entries.
Green (Proceed) LED + single beep occurs
1. After entering each digit of Factory or User Code, or
Password
2. After pressing Clear key
3. After pressing Program key
Green LED only
1. Comes on after you enter a valid code/password and
remains lit during the 4-second period in which the safe
can be opened.
2. Comes ON in the Program User Code mode after you enter
the Factory Code and remains lit until you have finished
entering a 5-digit User Code.
3. Comes ON in the Program Password mode after you have
entered your User Code and remains ON until you have
entered a 5-digit password.
Yellow LED
Indicates low battery and will typically not turn ON until
battery has been in use approximately two years or longer.
Your electronic lock automatically performs a low battery test
during each lock use.
If a ï¿½low batteryï¿½ condition is detected the Yellow LED will
come ON and remain ON during each subsequent lock
operation. (The lock will continue to function in a Low Battery
state, until battery failure.) The Yellow LED will turn OFF only
after three consecutive Good Battery readings or after the low
batteries are replaced. (Note: If the new batteries are installed
in less than 60 seconds the Yellow LED may come ON and stay
ON during the first lock operation before it returns to OFF.)
NOTE: It is recommended you replace the batteries after two
years, or when the yellow LED remains on.

Jan 09, 2011 • Safe International Electronic Digital Safe...

0helpful

1answer

We are trying to reset a security code for our existing weiser lock and it isn't taking the new code entered.

To program the first code, press the reset button once, then enter your 4-8 digit code on the exterior keypad, then immediately press the middle lock button on the exterior keypad. You will hear a beep. This signals that your code has been accepted.
To program the second code, press the reset button twice , then enter your 4-8 digit code on the exterior keypad, then immediately press the middle lock button on the exterior keypad. You will hear a beep. This signals that your code has been accepted.
To program the third code, press the reset button 3 time, then enter your 4-8 digit code on the exterior keypad, then immediately press the middle lock button on the exterior keypad. You will hear a beep. This signals that your code has been accepted.

Good lock
Good unlock

Nov 08, 2010 • Weiser Lock Powerbolt 1000 Lock

0helpful

1answer

The original code will not clear from my Weiser lock electronic lock. I have entered multiple codes and the original still stays. How do I get the original to clear.

First, I fix this problem after an hour of try.

I conclude that this dorr lock is better that is appear. Is not a 2 codes door lock, it's a 3 codes one.. and the problem you have is the third code not reset. You can put the same code in each third emplacement. you have just to press the program button 3 time for the third code...

I determinate that I put the third code by error the was i program it the firs time.

;-)

I guide you...

To program the first code, press the reset button once, then enter your 4-8 digit code on the exterior keypad, then immediately press the middle lock button on the exterior keypad. You will hear a beep. This signals that your code has been accepted.
To program the second code, press the reset button twice , then enter your 4-8 digit code on the exterior keypad, then immediately press the middle lock button on the exterior keypad. You will hear a beep. This signals that your code has been accepted.
To program the third code, press the reset button 3 time, then enter your 4-8 digit code on the exterior keypad, then immediately press the middle lock button on the exterior keypad. You will hear a beep. This signals that your code has been accepted.

May 04, 2010 • Weiser Lock POWERBOLT ELEC DEADBOLT

1helpful

1answer

Have a Rona electronic lock (Weiser) and the key works... will lock electronicly... but do not know the code... I have removed it from the door and replaced, but is there a way to reset the code?

First, I fix this problem after an hour of try.

I conclude that this dorr lock is better that is appear. Is not a 2 codes door lock, it's a 3 codes one.. and the problem you have is the third code not reset. You can put the same code in each third emplacement. you have just to press the program button 3 time for the third code...

I determinate that I put the third code by error the was i program it the firs time.

;-)

I guide you...

To program the first code, press the reset button once, then enter your 4-8 digit code on the exterior keypad, then immediately press the middle lock button on the exterior keypad. You will hear a beep. This signals that your code has been accepted.
To program the second code, press the reset button twice , then enter your 4-8 digit code on the exterior keypad, then immediately press the middle lock button on the exterior keypad. You will hear a beep. This signals that your code has been accepted.
To program the third code, press the reset button 3 time, then enter your 4-8 digit code on the exterior keypad, then immediately press the middle lock button on the exterior keypad. You will hear a beep. This signals that your code has been accepted.

Jan 23, 2010 • Weiser Lock Powerbolt 1000 Lock

0helpful

1answer

I have a Samsung U520 and I accidentally activated NAM2. Now my phone does not work. When I try to deactivate NAM2 it asks for a password. Can you help? It needs a 4 digit code. It also states Initial...

hi sir have you done restore factory settings firstThe Nokia 2160 series hand portable CMT uses an EEPROM NAM that can be programmed directly from the standard user keypad. In order to access the
NAM, you must enter the special access code currently programmed into the
phone. Once the programming mode is accessed, NAM parameters are loaded
by entering them into the display and "storing" them to selected memory
locations. Be sure to obtain all parameters before proceeding.

EASY NAM PROGRAMMING

1. Turn on phone.

2. Enter the Easy NAM access code. Access code is: *#639#

3. Verify the display now reads "Cellular Number" and enter the 10 digit
MIN for the phone.

4. Press the softkey under the word "OK" in the display. If less than 10
digits are entered an error message will prompt you to reenter the
number.

5. Verify the display reads "Enter code" and enter the five digit SID
followed by four zeros. (Example 001750000 is a SID of 175 followed
by four zeros). An error message will display if an incorrect entry
is made. Do not add more than four zeros to the code.

Note: Change the Lock code by adding a pound sign and new lock code after
the code. (Example: 001750000#7788. Lock code = 7788).

Change the Language code by adding a pound sign (#) and new
language code after the code. (Example: 001750000#2. Language = 2)

Language Code: 0 (default) = English, 1 = French, 2 = Spanish,
3 = Portuguese

Change the Lock code and Language code by separating each set of
numbers by a pound sign. (Example: 001750000#7788#2). The SID =
00175, Lock code = 7788, Language = 2 (Spanish).

6. Press the softkey under the word "OK" in the display.

7. The display will tell you t

Sep 10, 2008 • Samsung Cell Phones

0helpful

1answer

Apex Digital GB4308 remote

Programming the Remote Control Remote-control switchover Press VCR/DVD, SAT/CABLE or AUX to select the device you want to control. To program the remote control Press and hold VCR.DVD, SAT/CABLE or AUX for over 2 seconds until the LED on the remote control turns off. Release the button the LED will light again (the remote control enters the PROGRAMMING mode). Enter three-digit code number for your equipment. If the correct code number is entered, the LED blinks three times. If you enter a code not listed below, or you press any other buttons than SEARCH and 100+, the LED turns off. To search codes Press ad hold VCR/DVD,SAT/CABLE or AUX for over 2 seconds unil the LED turns off. Release the button (the LED wil light again) and the remote control enters the PROGRAMMING mode. Press SEARCH. Press CH+/- to search codes downwards or upwards. Each time you press CH+/-, the code number decreases or increases by 1 while the remote control sends the code number for POWER button on your device. If the desired code number is found,press 100+ to program the code for your device until the LED blinks three times.Then the remote control exits from the PROGRAMMING mode and returns to norml operation. Or press any other button to exit from the PROGRAMMING mode after the LED blinks rapidly eight times, and the operation is not active. To check the current code number Press and hold VCR/DVD, SAT/CABLE or AUX for over 2 seconds until the LED turns off. Release the button (the LED will light again) and the remote control enters the PROGRAMMING mode. Press 100+ . You may read the code numder according to the LED display status as follows. * If there is no operation within 20 seconds during the steps mentioned above, the remote control will automatically exit from the appropriate operation. Code Number First - digit 0 1 0 1 Second - digit 0 0 4 5 Third - digit 0 6 3 0 First - digit Blinks rapidly once Blinks once Blinks rapidly once Bliks once Secod - digit Blinks rapidly once Blinks rapidly once Blinks four times Bliks five times Third - digit Blinks rapidly once Blinks six times Blinks three times Bliks rapidly once

Jan 05, 2007 • Apex Digital GB4308 43" Rear Projection...

Question 2

Anonymous

Expert 59 Answers
Posted on Aug 30, 2009

Anonymous

Expert

Joined: Aug 21, 2009

Answers

59

Questions

0

Helped

36015

Points

156

Restore the lock first

1.disconnect battery
2.press and release the SCHLAGE button
3.reconnect the bat and wait until SCHLAGE is no longer lit.
4. within 10 sec,press and hold SCHLAGE until SCHLAGE lights green and the lock beeps.

The lock is back to factory now.
Now add your user code.

Adding a new user code
DPC is-digit programming code
DUC is digit user code
Yellow sticker has factory 6 digit programming and 4 digit user code on it.

1. 6DPC push SCHLAGE, push 1, enter 4DUC twice.

this lock will only take 2 user codes.

Hope this helps. Leave feedback for others if it helps

Testimonial: "Yes this did the trick. I changed the programming code so long ago I could not remember it. "

Related Topics:

1 Answer

Anonymous

Add Your Answer

Attachments: Added items

Related Questions:

I have a Defiant Electronic deadbolt from home Depot. model G1X2D01. ive lost the manual and i need to delete some old codes from it.

I need the tv code number to put into my Jensen Universal remote control for a Panasonic TV on cable, TV Model# CT-27S18S. I also need to know how to program these numbers into the Jensen remote Remote...

How do I play regional dvd's that the player is not tuned to. I have been trying to find a code but I am struggling. Can you help me?

Does not overwrite old codes, just keeps accepting new ones. How can I clear all existing codes?

Just put new batterys in safe . but safe will not stop bleeping what is the problem

We are trying to reset a security code for our existing weiser lock and it isn't taking the new code entered.

The original code will not clear from my Weiser lock electronic lock. I have entered multiple codes and the original still stays. How do I get the original to clear.

Have a Rona electronic lock (Weiser) and the key works... will lock electronicly... but do not know the code... I have removed it from the door and replaced, but is there a way to reset the code?

I have a Samsung U520 and I accidentally activated NAM2. Now my phone does not work. When I try to deactivate NAM2 it asks for a password. Can you help? It needs a 4 digit code. It also states Initial...

Apex Digital GB4308 remote

Not finding what you are looking for?

BE365-PLY BE365PLY626 Satin Chrome Electronic Security Keypad Elect

I have a Defiant Electronic deadbolt from home Depot. model G1X2D01. ive lost the manual and i need to delete some old codes from it.

Ask a Question

Top Schlage Locks & Locksmithing Experts

Cindy Wells

Brad Brown

john h

Are you a Schlage Lock and Locksmithing Expert? Answer questions, earn points and help others

Manuals & User Guides

Related Topics:

1 Answer

Anonymous

Add Your Answer

Attachments: Added items

Related Questions:

I have a Defiant Electronic deadbolt from home Depot. model G1X2D01. ive lost the manual and i need to delete some old codes from it.

I need the tv code number to put into my Jensen Universal remote control for a Panasonic TV on cable, TV Model# CT-27S18S. I also need to know how to program these numbers into the Jensen remote Remote...

How do I play regional dvd's that the player is not tuned to. I have been trying to find a code but I am struggling. Can you help me?

Does not overwrite old codes, just keeps accepting new ones. How can I clear all existing codes?

Just put new batterys in safe . but safe will not stop bleeping what is the problem

We are trying to reset a security code for our existing weiser lock and it isn't taking the new code entered.

The original code will not clear from my Weiser lock electronic lock. I have entered multiple codes and the original still stays. How do I get the original to clear.

Have a Rona electronic lock (Weiser) and the key works... will lock electronicly... but do not know the code... I have removed it from the door and replaced, but is there a way to reset the code?

I have a Samsung U520 and I accidentally activated NAM2. Now my phone does not work. When I try to deactivate NAM2 it asks for a password. Can you help? It needs a 4 digit code. It also states Initial...

Apex Digital GB4308 remote

Not finding what you are looking for?

BE365-PLY BE365PLY626 Satin Chrome Electronic Security Keypad Elect

I have a Defiant Electronic deadbolt from home Depot. model G1X2D01. ive lost the manual and i need to delete some old codes from it.

Related Topics

Ask a Question

Popular Questions

When I press the Schlage button the door automatically unlocks.

How do you erase an old code and input a new code?

Schlage keyless deadbolt....has worked great for two years, suddenly when code is entered and accepted, cylinder just spins, without moving deadbolt. Battery is good.

Schlage FE595 keypad replacement part

Schlage FE365v keyless entry lock.. Lost manual. Forgot 6 digit programming code. Need instructions to restore and set all new codes.

Top Schlage Locks & Locksmithing Experts

Cindy Wells

Brad Brown

john h

Are you a Schlage Lock and Locksmithing Expert? Answer questions, earn points and help others

Manuals & User Guides