Question about KitchenAid 24 in. KUDI02IR Built-in Dishwasher

1 Answer

Whirlpool quiet partner III. Clean light keeps flashing clean.

The clean light keeps flashing and won't reset to clean the dishes. I have pushed the drain button and cancel button, yet no response. The clean button continues to flash. This dishwasher is a whirlpool quiet partner III.

Posted by trubbl470 on

  • Anonymous Mar 15, 2014

    LreA

×

Ad

1 Answer

Anonymous

  • Level 1:

    An expert who has achieved level 1.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    New Friend:

    An expert that has 1 follower.

    Corporal:

    An expert that hasĀ over 10 points.

  • Contributor
  • 1 Answer

Had the same problem. Press the sani-rinse and heated dry button back and forth and it should reset.

Posted on Dec 29, 2009

  • Steve Hanson Aug 29, 2013

    Thank you it worked

×

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The clean light keeps blinking on my whirlpool quiet partner 1 dishwasher


Are the dishes clean??? try unplugging (15-20mins) the unit and see if it resets the unit.

Oct 17, 2014 | Whirlpool Dishwashers

2 Answers

Whirpool dishwasher quiet partner 2 clean light blinking wont cancel or run a cycle


Hello,

press normal heated dryer normal heated dry normal the dishwasher should reset and start. You will need to check the heater this happens because the heater normally fails. Let me know,

http://www.appliancerepairlesson.com/

Mar 07, 2011 | Whirlpool GU2400XTP Built-in Dishwasher

1 Answer

I have a Whirlpool Gold Quiet Partner III dishwasher. When I unload the "clean" dishes, there is some type of film or crud on the dishes. I have to hand wash them to get this off. It seems like a...


You need to check the drain system completely, look for plugged screens, pump impellers, valves and the drain hose. You need to witness a large volume of water flow during drain.

Sep 19, 2010 | Whirlpool Dishwashers

1 Answer

Our quiet partner iii dishwasher is not working. It is not gettting dishes cleaned soap left on dishes


Our whirlpool gold quiet partner iii dishwasher is not working well . It is not gettting dishes cleaned soap left on dishes on top primarily

May 16, 2010 | Dishwashers

1 Answer

I have a Quiet Partner III, when I press start it doe not come on. The clean light flashes when the door is open, but when I close it and try to start it nothing happens


The clean light is blinking due to an error in heating the water. I have put together some instructions on resetting the control so you can use the dishwasher and what to look for as far as cause.

Follow the link and let me know if it helps.

http://www.fixya.com/support/r4628906-flashing_or_blinking_green_clean_light_7

May 10, 2010 | Whirlpool Dishwashers

1 Answer

Constant flashing clean light


count the blinks shoud be 7 times it blinks then a pause if it does that its a heat circute problem need to check the heater and replace the controls

Jul 13, 2009 | Whirlpool Dishwashers

2 Answers

I have a whirlpool Quiet Partner I. HELP Drain light flashing


This may or may not help in your situation, but the following link explains how you can clear the blinking clean light problem:

http://www.fixya.com/support/r417123-blinking_clean_light_kenmore_whirlpool

Now...keep in mind all dish washers are not alike and have different panel options. If you do not have the same set up as I have referenced, the tech sheet for your dishwasher will explain. The tech sheet is located behind the lower toe panel under the door and lists the proper sequence of buttons to push for diagnostics and troubleshooting.

NOTE: Sometimes the tech sheet is located behind the inner door panel. You will need to remove the screws securing the inner panel to access it if this is the case. Make sure you turn off the main power breaker before doing so.

Sometimes this can be a momentary glitch in operation. However, if the problem keeps reoccuring the number of flashes is an indication of which circuit is causing your problem. Again, refer to your tech sheet to determine this.

If you have any questions, please let me know. I hope this fixes your problem.

Jul 11, 2009 | Whirlpool DU1055XTS Built-in Dishwasher

1 Answer

Whirlpool Quiet Partner 980


Bad control board ,replace it.

May 26, 2008 | Dishwashers

Not finding what you are looking for?
KitchenAid 24 in. KUDI02IR Built-in Dishwasher Logo

4,071 people viewed this question

Ask a Question

Usually answered in minutes!

Top KitchenAid Dishwashers Experts

Michael Thomas
Michael Thomas

Level 3 Expert

3056 Answers

Mike

Level 3 Expert

4372 Answers

Cindy Wells

Level 3 Expert

6220 Answers

Are you a KitchenAid Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...