Question about Philips Senseo HD7832 Coffee Maker

1 Answer

Senseo 7814 does not heat water and red light keeps flashing

Have been given this machine but it doesn't work. I have flushed it several times, returned it to boiler shut state (power on and 1 button) and re-flushed but still no joy.

Posted by trevor_h on

Ad

1 Answer

Anonymous

  • Level 1:

    An expert who has achieved level 1.

    Governor:

    An expert whose answer got voted for 20 times.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 6 Answers

Is the red light flashing as though not enough water, if so use a magnet to connect to the valve inside the machine, the valve can be found along the water level where the float is. what is happening is that the float is stuck. by connecting the magnet to the valve and very slowly moving the magnet along the water level, upwards the valve will follow and the water will begin to heat as the light changes to a slow flash, if it doesn't work try again as you have not connected to the magnet

Posted on Oct 16, 2009

  • Jacqueline Noy Jun 12, 2012

    thanks jtotney your problems solving idea of using a magnet along the water level of
    the water container has done the trick. Many thanks Jacqueline

×

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

No hot water from certain time of the day living in a single family home with wall thermostste


see the following steps:
If the unit produces no heat, raise the thermostat, check switches, fuses, circuit breakers, and the water level. Also check the burner's safety controls (see below).
If the unit doesn't produce enough heat, check the combination gauge, then the expansion tank (see below). Next, flush the boiler (see below). If water leaks from a heating system pipe, try repairing it yourself.
If only some radiators in the system heat up, bleed air from the cool units (see below). If you suspect that the circulator requires repair, call an experienced serviceperson.
If the pipes suddenly start clanging, the circulator may need professional service or replacement.
If there is a chronic banging noise, check the slope of all return lines; they must slope toward the boiler to work correctly.
If a single radiator warms only slightly, but evenly, water may be trapped inside. Make sure it slopes toward the return; if it does not, insert a wooden shim under the end opposite the return.

7_22_2012_8_41_30_am.jpg

Jul 21, 2012 | Heating & Cooling

1 Answer

Dor does not open


This is a common problem, often associated with a momentary power failure when the controller doesn't get time to reset and return to an idle state before the machine gets power back and it gets "confused". Regardless of the cause, you will almost certainly find that unplugging from the mains (Not just powering off on the button, as some door locks have a sneak circuit, even when the power is turned off at the button) and leaving the machine undisturbed for a full 20 minutes will allow a reset, the door lock will disengage and all will be well when you power back up.
Additionally, on older machines with analog program selectors, turn the selector to an end of program setting before you power it off.

Jul 29, 2011 | Hotpoint Dryers

1 Answer

Door won't open on my wd-8015c washing machine


This is a common problem, often associated with a momentary power failure when the controller doesn't get time to reset and return to an idle state before the machine gets power back and it gets "confused". Regardless of the cause, you will almost certainly find that unplugging from the mains (Not just powering off on the button, as some door locks have a sneak circuit, even when the power is turned off at the button) and leaving the machine undisturbed for a full 20 minutes will allow a reset, the door lock will disengage and all will be well when you power back up.
Additionally, on older machines with analog program selectors, turn the selector to an end of program setting before you power it off.

Jul 22, 2011 | Washing Machines

1 Answer

It is stuck on 'end' and wont unlock


This is a common problem, often associated with a momentary power failure when the controller doesn't get time to reset and return to an idle state before the machine gets power back and it gets "confused". Regardless of the cause, you will almost certainly find that unplugging from the mains (Not just powering off on the button, as some door locks have a sneak circuit, even when the power is turned off at the button) and leaving the machine undisturbed for a full 20 minutes will allow a reset, the door lock will disengage and all will be well when you power back up.

Jul 19, 2011 | Samsung WF337AA Front Load Washer

1 Answer

How do you unlock the door when the washer freezes up?


This is a common problem, often associated with a momentary power failure when the controller doesn't get time to reset and return to an idle state before the machine gets power back and it gets "confused". Regardless of the cause, you will almost certainly find that unplugging from the mains (Not just powering off on the button, as some door locks have a sneak circuit, even when the power is turned off at the button) and leaving the machine undisturbed for a full 20 minutes will allow a reset, the door lock will disengage and all will be well when you power back up.

Jul 18, 2011 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

MACHINE LOCKED, HOW CAN I OPEN IT


This is a common problem, often associated with a momentary power failure when the controller doesn't get time to reset and return to an idle state before the machine gets power back and it gets "confused". Regardless of the cause, you will almost certainly find that unplugging from the mains (Not just powering off on the button, as some door locks have a sneak circuit, even when the power is turned off at the button) and leaving the machine undisturbed for a full 20 minutes will allow a reset, the door lock will disengage and all will be well when you power back up.

Additionally, on older machines with analog program selectors, turn the selector to an end of program setting before you power it off.

Jul 08, 2011 | Samsung Washing Machines

1 Answer

Have replaced drums in printer and after turning the printer off and on several times, there is still a message saying "drums end soon"


1) Press the 1 and 7 buttons at the same time in the ready
status.

(2) The "Reset Menu" will appear on the LCD. Select the
applicable periodical replacement part by pressing the up arrow or down arrow button and press the OK button.

- Drum - Belt Unit - PF KitMP - PF Kit1
- PF Kit2 - Fuser - Laser

(3) When the OK button is pressed the "1. Reset 2. Exit"
appears on the LCD. Press the 1 button if resetting the
counter. If not, press the 2 button.

(4) Pressing the 1 button accepts that the machine implements
the counter reset.

(5) If the 2 button is pressed the machine goes back to the
select part counter again. If you need to Exit press the
Stop/Exit button at any time.

(6) The machine returns to the ready status.

Note:

- All periodical replacement parts are always indicated on the LCD even though their lives do not reach 0 %.

- The PF kit2 is always indicated even though Tray 2 is not installed, or it is not supported for the model to be used.

- The machine returns to the ready state automatically if no panel operation is implemented for 60 seconds.




Jan 17, 2011 | Brother MFC-9420CN All-In-One Laser...

1 Answer

#1 Thermostats are not working properly #2 I have


Using an ohms meter check the thermostats and replace the broken one, I think it is most likely the coffee thermostat.

Sep 27, 2010 | Rancilio Silvia Espresso Machine

1 Answer

When I turn on the machine it just says flushing and won't go any further.


Machine wants to flush but the boiler may not be up to temp.. with the machine off " Stand By " hold down the on/off and cleaning button at the same time release at the same time. "clear Flag should appear.. check for tripped hi limits on hot water boiler

Sep 12, 2010 | Schaerer Siena Espresso Machine

3 Answers

Trouble with Rowenta Irons


If your Rowenta DG 920 is chucking guff from the steam jets you need to flush it as per the instructions. ( ie. Flush every 10 uses ) If you haven;t done it for somewhile, you'll next need to expel the reamining guff with lots of steam. Then no more probs.

Aug 05, 2008 | Rowenta DG-980 Iron

Not finding what you are looking for?
Philips Senseo HD7832 Coffee Maker Logo

5,929 people viewed this question

Ask a Question

Usually answered in minutes!

Top Philips Coffee Makers & Espresso Machines Experts

Ross Keen

Level 3 Expert

1364 Answers

Piers Carter
Piers Carter

Level 2 Expert

46 Answers

Harrie

Level 3 Expert

6746 Answers

Are you a Philips Coffee Maker and Espresso Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...