Maytag Neptune dryer MDE 6700AZW Stops working

FIXED Maytag Neptune, Timer Problem - ApplianceBlog

www.applianceblog.com/.../23387-Maytag-Neptune-Timer-Problem

Mar 4, 2011 - 8 posts - ‎3 authors
My countdown timer is stuck at the 33-minute level in the "wash cycle", and repeatedlyruns for a 30-40 seconds, then stops, then runs, then ... Maytag Neptune TL Washing Machine stops in spin cycle ...
10 posts
Jul 25, 2013
Maytag Neptune Washer Won't Spin/drain
7 posts
Jul 4, 2013
Neptune TL Washer FAV6800AWW - DC and UC ...
5 posts
Jul 3, 2007
MAYTAG NEPTUNE WASHER CONTROL PANEL ...
8 posts
Jun 29, 2005
More results from www.applianceblog.com

Troubleshooting a Too-Long Wash Cycle - whirlpool washingmachine ...

ask.metafilter.com/233920/Troubleshooting-a-TooLong-Wash-Cycle

Jan 25, 2013 - We have a Whirlpool Duet washing machine (about 2 years old). Thecycle is taking WAY too long to complete. The load that's running now ...

Maytag Neptune washer repair: motor/motor control circuit ...

? 12:10
https://www.youtube.com/watch?v=ITTbDh8CFEU
Dec 11, 2013 - Uploaded by daytonaturbofreak
Maytag Neptune washer motor/motor control circuit board ... my board just fried - is your washer still working? wondering how longthe conversion fix will last. ... Other times it will run a completecycle without any malfunctions.

If the timer is not stopping as it goes around then it's for sure the timer. The timer does pretty much all the work with controlling the dryer. And if it's physically not stopping going around then it has broken.

Repair needed on Maytag Neptune washer - Home Improvement ...

www.dslreports.com > ... > Home Improvement

DSLReports
Aug 5, 2007 - 19 posts - ‎8 authors
Forum discussion: We have a Maytag Neptune front-loader washing machine that ...the drain/spin cycle after a wash even though the timer continues to ... related circuit board failure" their Neptune washer will lock the door, turn on the ... then will either not start tumbling or will stop operation mid-spin cycle.

How To Fix A Washing Machine That Is Not Spinning or ...

removeandreplace.com/.../washing-machine-or-washer-dryer-is-not-spin...

May 13, 2013 - The absolute first thing to do to your washing machine that will notspin or drain (whether it. ... I was so fed up with the machine sometimes refusing to spin or drain the .... I just did a load and it stopped midcycle with e and f error codes.... I tried different cycles but all that happens is the door lock engages ...

Maytag Washer Troubleshooting - YouTube

i fitted a new membrane panel /sticker to front panel this fixed the problem 1 year ago

Verify there is still power at the wall and check the thermal fuse.
Eric

You may be experiencing "Heat Retention" by stopping your dryer mid-cycle, which you should NOT ever have to do! If you have a minor vent restriction or if you open the dryer mid-cycle when the heat is on, this will cause a disruption in the airflow and rising temperatures can keep the dryer from restarting until it has been cooled long enough.
Check your vent all the way to the outside for restrictions/obstructions every 6 months. Clean your lint filter after each load and DO NOT stop the dryer mid-cycle!
Note: Stopping the dryer mid-cycle can also cause severe burns and even melt polyester fibers.

Q - My gas dryer will not heat, what could stop my dryer from heating?
A - Things that could stop a gas dryer from heating:
- glow bar igniter, thermal fuse ( not all models ), coils on the gas valve, gas valve, thermostats,motor heat switch, timer, selector switch, sensor.
A page for checking gas dryers is here.

get a new switch or timer.

The maximum run time on this machine's timer is 54 min. There is an adjustable peg on the white plastic index wheel which you can adjust anywhere from 30 to 54 min. For example peg in position E is 30min, D is 36min, C is 42min, B is 48min or for 54 min you have to remove the adjustable peg completely, but don't lose it in case you want to change the time in the future. If it is already in the Max "A" position and shuting off early you might have to change your torsion return spring. Hope this helps

SOUNDS LIKE SOMETHING STUCK IN PUMP