Question about Baumatic 18 in. BFD47 Free-standing Dishwasher

1 Answer

Buamatic dishwasher- cycle is not completing when running- gets stuck.

Hi
One day, my one year old dishwasher just stopped by itself, in the middle of the normal cycle, I have since then tried to check the water presure and remove cables and pipes and reconnect but it is still doing the same.Can anyone please help me to understand what is happening here, it gets stuck after running for about 10 minutes, and there is no water in the washer when I open it at the stuck stage

Posted by jjyoti76 on

Add Your Answer
Ad

1 Answer

Anonymous

  • Level 1:

    An expert who has achieved level 1.
    MVP:

    An expert that got 5 achievements.
    Scholar:

    An expert who has written 20 answers of more than 400 characters.
    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 67 Answers

The fill valve may not be telling the unit that it is empty. Try pushing it down and see if it will restart.

Posted on Nov 30, 2007

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

DISHWASHER GETS STUCK ON THE 1ST RINSE CYCLE
see the diagram attached.
1) Test the switch door,it is defective, the starting relais turn off, and consequenc the motor off.

2) TIMER: TEST FOR DEFECTIVE, clean contacts, repair wires loose, burn or broken.
God bless you

5_10_2012_11_32_44_am.gif5_10_2012_11_32_58_am.gif5_10_2012_11_33_18_am.gif
Read full answer
May 09, 2012 • Candy Dishwashers
0helpful
1answer

24 in. GU980SCG Built-in Dishwasher: My dishwasher (GU980SCGB3) now stops at the rinse ...
Looks like micro controller problem. Contact service center for assistance.
Read full answer
May 17, 2010 • Whirlpool 24 in. GU980SCG Built-in...
3helpful
1answer

Asko 1385: 13 year old dishwasher stops during cycle. If you push on the middle of the door it starts again. It is like the latch is not working properly but by all appearances the latch works fine....
when you latch the door it closes the circuit.
you may have to open the casing of the door to access the switch. it may be stuck or defective.
Read full answer
May 15, 2010 • Asko 1385 Dishwasher
0helpful
3answers

Washer turns on by itself. (Once in the middle of the night)
i have the whirlpool top loader also. Was not quiet a year old, starts running at random by itself. They sent the repair man out got lectured that it was my fault (too much soap, washer is in basement, I need to call an electrician to check the wiring). Now it drips water into the inside of the washer.
I can see it will eventually be cheaper to replace than call the repairman back.... Won't be a Whirlpool
Read full answer
May 29, 2009 • Whirlpool Calypso GVW9959K Top Load Washer
2helpful
1answer

Dishwasher only runs for 21 minute cycle
I bought and replaced the control board in the door. $145 CAD it took 5 min saved myself $300
Read full answer
May 07, 2009 • Dishwashers
0helpful
1answer

IT IS STUCK , IT JUST HUMMS ,CYCLE DOES NOT START
I PULLED THE DISHWASHER OUT FROM UNDER MY KITCHEN TOP. THEN TRIED IT AGAIN AND IT STARTED WORKING. WATER WAS ENTERING THE MACHINE AS IT SHOULD AND THE WHOLE CYCLE WAS COMPLETED FROM WASHING TO DRYING. BUT WITH THE ODD RATTLING SOUND NOT COOMING FROM DISHES. I ASSUME THE INLET PIPE WAS PROBABLY BENT THEREFORE BLOCKING WATER COMING IN BUT WHY NOW AFTER YEARS OF BEING IN THAT POSITION. THE OTHER THING I CHANGED WAS THE ELECTRIC SOCKET POINT- IE I PLUGGED IT IN SOMEWHERE ELSE BECAUSE MOVING IT MEANT THE LEAD COULD NOT REACH ORIGINAL SOCKET. HOPEFULLY WHEN I RETURN IT TO ORIGINAL POSITION EVERYTHING WILL BE WORKING. FUNNY THING HAPPENED THE WEEK BEFORE- MY WASHING MACHINE WAS STUCK IN MIDDLE OF A CYCLE . BUT STARTED WORKING THE FOLLOWING DAY. COULD IT BE MY ELECTRICITY PERHAPS - IE MY APPLIANCES ARE NOT RECEIVING ENOUGH CURRENT?
Read full answer
Dec 04, 2008 • Dishwashers
3helpful
1answer

Whirlpool gold dishwasher gets stuck at 53 minutes left for an hour
Try "resetting" the control board by running the diagnostic cycle. The cycle completes in 15 minutes. 
The details are in the service manual. The manual can be found hidden behind the tow plate (at the very bottom front of the washer).
The diagnostic cycle may tell you the problem. It also helps clear up some of the software gltiches. 
It is easy to run the diagnostic cycle.
Just the buttons in the following sequence. The sequence should be complete within 6 sec. 
heated dry -> Normal -> heated dry -> Normal
This will trigger diagnostic cycle of 19 intervals. Pay special attention to the intervals 18, 17, 9, 6, 4.
Interval 18 - displays your controller module number (should be letter 'd' followed by number 0 or 1 or 2 or something. Note that down for future reference.
Interval 17 displays 'software generation number' Note that down for future reference.
Then wait until you reach interval 9.  --- clean LED turns on - then an open or shorted thermister is detected.
-- Sanitized LED turns on - then the washer detected greater than 100 deg F temperature
Interval 7
-- Soaking/sensing LED should NOT come on (unless food soil is present).
Interval 4 -- Soaking/sensing LED should come on


Let the cycle complete and then try running the normal wash. Hopefully the possible glitches are cleared by now and you should have no problem. 
If this doesn't work, time to call the expert tech. 
Read full answer
Nov 08, 2008 • Whirlpool Gold 24 in. Built-In Dishwasher...
1helpful
2answers

Bosch SHU43C
My SHU43C is just over 3 years old. I had a similar problem recently. First, there were a few floods. Then, the Bosch only drained non-stop. Even when I used the Cancel Drain buttons the drain pump would run without stopping. When I tried to run one of the cleaning cycles, no water entered the machine. Corrective: I removed the base plate, and saw that the red plastic floatation device was in the up position. Using a flashlight and a wooden spoon, I lightly toggled the red float stem down. I pushed regular clean cycle and kept toggling with the red float stem until the rinse water started to enter the machine (turning the red stem seems to also actuate a step in the program). Now the dishwasher runs normally. Voila!
Read full answer
Jun 22, 2008 • Bosch 24 in. SHU43 Built-in Dishwasher
2helpful
1answer

LG Dishwasher Model LD-1403W gets stuck and stops on rinse cycle leaving water in bottom of machine. I have stripped it down and emptied it, made sure filters etc are clean but to no avail
LG Dishwasher LD 1403W. We have cleaned it and when it gets to the heating cycle after running right through to nearly the end, it trips all the electricity and stops everything. Its only 3 years old and hubby thinks its the heating element but between $200=$300 to fix.
Read full answer
Apr 10, 2008 • Dishwashers
0helpful
2answers

My Kenmore diswasher gets stuck between the quick rinse and drying cycle
I am having the same issue as described above. I think it is either the timer, thermostat (temp assure), or thermostat (temp boost) that needs replacing. The dial gets stucks in both the wash temp boost cycle and rinse temp boost cycle. However, I don't have a picture of the temp assure or boost part. Does anyone know how to fix this? Thanks. -Bill
Read full answer
Aug 31, 2006 • Kenmore 16602 / 16604 / 16609 Built-in...
Not finding what you are looking for?

View Most Popular

18 in. BFD47 Free-standing Dishwasher

  • Dishwashers

Related Question

DISHWASHER GETS STUCK ON THE 1ST RINSE CYCLE

  • Candy Dishwashers

Open Questions:

0answers

When dishwasher comes to drain there is an error 2 displayed. Please assist
Read full answer
Be the first to answer Dec 10, 2010 • Baumatic 18 in. BFD47 Free-standing...
0answers

The dial that controls the wash is not turning, we have to manually turn it around to get anything washed.
Read full answer
Be the first to answer Oct 18, 2010 • Baumatic 18 in. BFD47 Free-standing...
0answers

display showing ERR 4
Read full answer
Be the first to answer Apr 07, 2010 • Baumatic 18 in. BFD47 Free-standing...

Related Topics

Baumatic 18 in. BFD47 Free-standing Dishwasher Logo

Related Topics:

346 views

Ask a Question

Usually answered in minutes!

Popular Questions

Error code E2

Baumatic 23 in. BDW13 Built-in...

Dishwasher keeps running

Baumatic 24 in. BFD60SS...

I need to reset my dishwasher but don't know how!!

Baumatic 23 in. BDW13 Built-in...

Hello I am getting error code E3 on my Baumatic

Baumatic 23 in. BDW13 Built-in...

Dishwasher showing e3 error

Baumatic 23 in. BDW13 Built-in...

Top Baumatic Dishwashers Experts

Oloyede Monsuru

Level 3 Expert

1468 Answers

Kolbrun...

Level 3 Expert

1218 Answers

Pierre Laplante

Level 3 Expert

2061 Answers

Are you a Baumatic Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...