Panasonic CQ-VD7001U Car DVD Player Logo

Related Topics:

Posted on Nov 29, 2007
Answered by a Fixya Expert

Trustworthy Expert Solutions

At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.

View Our Top Experts

Non responsive display panasonic CQ-VD7001Ucar dvd.

Display is in open down flat position and will not respond to any controls ,even after reset.

  • chrisnkaysee Oct 20, 2008

    i have the same problem and it came out and tilted to bout 45deg and stoped and never closed or opened again it is stuck there. i checked the ribon and its in great shape no problem there even checked conuite on the ribon and everything is fine any other ideas/???

×

1 Answer

hogan doan

Level 2:

An expert who has achieved level 2 by getting 100 points

MVP:

An expert that got 5 achievements.

Champion:

An expert who has answered 200 questions.

Governor:

An expert whose answer got voted for 20 times.

  • Expert 227 Answers
  • Posted on Mar 06, 2008
hogan doan
Expert
Level 2:

An expert who has achieved level 2 by getting 100 points

MVP:

An expert that got 5 achievements.

Champion:

An expert who has answered 200 questions.

Governor:

An expert whose answer got voted for 20 times.

Joined: Jan 24, 2008
Answers
227
Questions
1
Helped
87300
Points
296

If it is a Pioneer then 99% that it has a cracked ribbon cable. The cable is flat and being dragged from slidding in and out. But I think the same apply for all brands. I have seen a cracked one from Audiovox. Are you incline enough to open it up to check? It take lot of patients, a steady hand and good memory(to put it back together). If not let someone who knows do it. Let me know how it goes. Goodluck.

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Frigidaire FGID2466QF7A dishwasher touchpad non-responsive

I called Frigidaire with these codes. They said it indicates a power failure happened (during a wash cycle, I suppose) and to do a hard reset. A hard reset is turning off the breaker for 30+ minutes and then flipping the breaker back on. This kind of worked, but simultaneous to the error codes, the push/pull latch on my dishwasher got set to the closed position while the door was open, so the door would not latch. I feel that this was the initial problem that caused these codes. So in my case, I had to manually rotate the latch open with bent piece of wire, to get it into the correct position first. Then the hard reset seemed fix the error codes. I was able to start a wash. It's running now.
0helpful
1answer

Tried to reset DMPBD79last step it shut off it wouldnt turn back on I just get a blinking redlight.

This is for a diff. model but give it a try, they may be diff. #'s showing up then what pops up on screen then is listed below.

  1. Remove any disc from the drive and switch the device to stand-by
  2. Press and hold [OK], [BLUE] and [YELLOW] simultaneously on the remote control until the device turns on and shows "00 RET" on the display
  3. Repeatedly press [RIGHT] on the remote control until the device shows "08 FIN" on the display
  4. Press and hold [OK] on the remote control for at least 3 seconds -> The device will reset itself to factory condition and show "HELLO" on the display
  5. Press [POWER] button on the remote control -> The device will shut down
1helpful
1answer

How do I make the keypad retract into the housing? It lays flat and goes up, but it wont return into its slot.

Simply using the [OPEN/CLOSE] button at the top of the display will cause the LCD monitor to retract.
1helpful
1answer

665.68601890 Acts as though it is not receiving power but breaker is not thrown. Is there an internal reset. Nothing responds - no lights, fan or microwave. Panel is black and non responsive

ther is on most microwaves a fuse inside usually located behind display panel located in a fuse block or will be on the control board itself.. normally a 20 amp fuse...try that first if not then make sure you have power to control and if so and no display most likely the display control board...
may luck out and be just the fuse though....good luck
2helpful
1answer

My Panasonic DVD recorder DMR-E60 doe not respond to its remote control. IT display DVD 2!

My Panasonic DVD recorder DMR-E60 doe not respond to its remote control. IT display DVD
2helpful
1answer

Panasonic DVD player not responding to remote control

Press enter and 1 on the r/c together for more than 3secs
1helpful
1answer

Remote not responding

Are you holding enter and channel number at the same time for about 2-5 seconds
11helpful
1answer

I ned code for panasonic cq-vx100u the mecanic desconect the bate

bought car yesterday they changed the battery and now there is a code display that has the unit locked up
0helpful
1answer

Non Responsive Buttons

Hello..
Is this system one that has speaker connections?
If so, all the speakers must be connected for it to work right.
1helpful
1answer

Non responsive dvd600 by Oritron

Can you take led off, see if DVD stuck inside unit? Find the tray release button and manually open the tray and replug. and see if unit respond.
Not finding what you are looking for?

149 views

Ask a Question

Usually answered in minutes!

Top Panasonic Car Audio & Video Experts

xxxxxx xxx

Level 3 Expert

5118 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8992 Answers

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Are you a Panasonic Car Audio and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...