Question about Radio Shack Pro-95 Handheld Scanner

1 Answer

Programming channel on start up

I have 2 different models here at my location. Zenith model L20V34S and Zenith model H2059DT. I need to program 87 as the switch on channel.
Any solutions?
My cell phone number is 602-820-2698 or or e-mail [email protected]

Posted by ttcphone on

Ad

1 Answer

Anonymous

Go to the installation menu and set the start up channel to whatever you would like

Posted on Jan 15, 2008

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1helpful
1answer

I replaced my TV and now my VCR Zenith Model 2100 will not record

Digital TV can use component video and stereo connections to record on analog VCR. Analog VCR needs DTV converter to record digital TV channels. VCR play back use AV channel on TV.
0helpful
2answers

Zenith L20V34S Completely DEAD Zenith LCD flat screen 20in Model: L20V34S Manufactered: Oct 2005 Listed HealthCare Facility TV Hello all, TV wont turn on (no red light either)after turning it...

The tv now is completely dead,no LED power light indication at all?Yes,than the tv power supply board 90-95% it is alway the problems and the causes.That the board,where the power a/c cord plug into it.Tries websites like Shopjimmy.com,Ebay.com to buy a refurbish power supply board for the replacement.
1helpful
1answer

I have an identical prestige remote which is not programed for my car iwould like to program it exatly like the one i now use so i can have a spare.

The programming procedure for Prestige/Pursuit remote is as follows:
First, locate the programming/valet switch. For newer model units the programming switch is located in the antenna, previous models have a push button LED (PBLED). Older models have a plain black push button, usually located near the driver's side kick panel (where your left foot would rest when driving).
After locating the programming switch; turn ignition on, press and release switch three (3) times,parking lights will flash once. This is channel 1 (lock button). Press lock button on remote. Parking lights flash once. Press and release switch one (1) time. Two flashes (channel 2). Press unlock button on remote. Press and release switch one (1) time. This is Channel 3 (trunk/remote starter), press the channel three button on remote. Repeat process for additional channels. Once you have programmed all available channels, turn ignition off to exit programming.
0helpful
1answer

I have a Zenith Tv that I bought from a resale store after it had been used by a hotel. When the hotel had owned it they had programmed it to return to a specified channel every time that it is turned off...

there should be an auto program on the menu, but you can also download the complete manual for this model here http://www.retrevo.com/support/Zenith-B27A11Z-TVs-manual/id/277dj086/t/2/
1helpful
1answer

I have a Sony Trinitron model KV27S35, but no remote. How do I program the tv without the remote?

The SETUP button on the case accesses the menu.
Press Channel +   to select Language.
Press Volume -    - now the tv will be reset to factory condition.
Press Channel + to start the AUTO PROGRAM and wait for it to finish.
Press Channel -  to exit it.
That is all. If you need more then all the menu options can be accessed thru the key on the tv.
2helpful
1answer

Old zenith 1999 model got from a hotel the program channel is locked can i unlock it

When you locked a tv you need the password, if you not get it, you will have replace the Eprom chip whith another recorded Eprom chip in acorded whith the tv model number.
1helpful
1answer

I cannot reset the channels on my TV. It is the Concierge TV from a hotel. Will I need to buy a Zenith Remote from the store to do the channel programming. It says it is locked

You have a hotel/motel model that cannot be programmed or any of the settings changed without a special Master remote. Sorry, doubt that you can buy one from the store, they are not sold to the public. Contact the hotel where you bought the set and try to get the model number for the remote from them. This is a different number than the model number of your tv.
1helpful
2answers

ZENITH MOTEL MODEL

Try to auto program the channels
0helpful
1answer

Zenith TV/VCR Combo, Model TVA 1923

Go to Radio Shack and get a basic universal remote, about 10 dollars. Once you program the tv with the remote you will be able to get all of the channels. The workers at Radio Shack are very helpful if you have any problems.
Not finding what you are looking for?
Radio Shack Pro-95 Handheld Scanner Logo

Related Topics:

141 views

Ask a Question

Usually answered in minutes!

Top Radio Shack Radio Communications Experts

Ekse

Level 3 Expert

13435 Answers

Brad Brown

Level 3 Expert

18854 Answers

NOEL
NOEL

Level 3 Expert

8555 Answers

Are you a Radio Shack Radio Communication Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...