Not open 192.168.0.30 can not enter inside it

Instructions

1. 1

   Enter your code on the keypad located on the front of the safe. Some electronic digital safes require you to input a special character like "#" before and after your code. The safe should either beep, have a LED turn green, or display "OPEN" if you have correctly entered the code.
   

2. 2

   Turn the handle to the right within five seconds of correctly entering the code. If you wait too long, the safe will lock and you will have to enter your code ag
   

3

Open the safe with a key. Use your emergency key that came with the safe to open it if you forgot the code or if the batteries have died. Remove the key cover from either the handle or the control panel to reveal the lock.

1. 1

   Enter your code to open the safe.
   

2. 2

   Place the electronic digital safe into code reset mode. On some models you need to hold the last digit of the code or press the "*" button to get into code reset mode. Other safes require you to open them and press a small red button on the inside of the door.
   

3. 3

   Enter your new code on the keypad and press "#" to finish. Some safes may require you to press "*" or a letter to finish the code. If the safe requires it, enter the new code again to confirm that you entered it correctly.
   

1. 1

   Use your code to open the electronic digital safe's door.
   

2. 2

   Locate and remove the battery cover on the inside of the door.
   

3. 3

   Replace the used batteries with new ones. For most safes, this will require two or four AA batteries.
   

4. 4

   Test the batteries. Use your code while the door is open to test the batteries before closing the safe.
   

On this model of keypad, you should be pressing "Enter" to open the door. Find the "Learn" button on your opener (usually on the back, or under the rear or side light cover, a red square button), press it, then go to your keypad, enter your 4-digit code, and press enter. The opener lights should flash. If this doesn't work, there may be another issue, for which you will likely need to contact a repair service.

follow this steps and fix it. see the pictures attached. God bless you

Open Lever

If the microwave door won't open the open lever might be broken. This part can be replaced separately.


Enter your model number to see parts for your microwave.
Help me find my model number

Door Spring

If the microwave door won't open the door spring may have broken. The door spring is located inside the door and keeps downward pressure on the door hook.


Enter your model number to see parts for your microwave.
Help me find my model number

Door Latch

If the microwave door won't open the door latch might be broken. The door latch is inside the microwave. The door hook, which is part of the door, engages with the latch to keep the door closed during operation. If the door latch or actuator breaks the door may not open.


Enter your model number to see parts for your microwave.
Help me find my model number

Door Hook

If the microwave door won't open the door hook might not be releasing properly. The door hook is installed inside the door and normally releases when the door is opened. The hook is made of plastic and will break over time. When this happens it will need to be replaced, it can't be repaired.


Enter your model number to see parts for your microwave.
Help me find my model number

Button Spring

If the microwave door won't open the button spring might be broken internally. The button spring can be replaced.


Enter your model number to see parts for your microwave.
Help me find my model number

Button

If the microwave door won't open the button might be broken internally. The button can be replaced.


Enter your model number to see parts for your microwave.
Help me find my model number

Handle Actuator

If the microwave door won't open the handle actuator might be broken. This is a plastic part which can become brittle over time. This part is connected between the door button and the door latch assembly.

proceed according . God bless you

Open Lever

If the microwave door won't open the open lever might be broken. This part can be replaced separately.

Enter your model number to see parts for your microwave.

Help me find my model number

Door Spring

If the microwave door won't open the door spring may have broken. The door spring is located inside the door and keeps downward pressure on the door hook.

Enter your model number to see parts for your microwave.

Help me find my model number

Door Latch

If the microwave door won't open the door latch might be broken. The door latch is inside the microwave. The door hook, which is part of the door, engages with the latch to keep the door closed during operation. If the door latch or actuator breaks the door may not open.

Enter your model number to see parts for your microwave.

Help me find my model number

Door Hook

If the microwave door won't open the door hook might not be releasing properly. The door hook is installed inside the door and normally releases when the door is opened. The hook is made of plastic and will break over time. When this happens it will need to be replaced, it can't be repaired.

Enter your model number to see parts for your microwave.

Help me find my model number

Button Spring

If the microwave door won't open the button spring might be broken internally. The button spring can be replaced.

Enter your model number to see parts for your microwave.

Help me find my model number

Button

If the microwave door won't open the button might be broken internally. The button can be replaced.

Enter your model number to see parts for your microwave.

Help me find my model number

Handle Actuator

If the microwave door won't open the handle actuator might be broken. This is a plastic part which can become brittle over time. This part is connected between the door button and the door latch assembly.

How to open new safe 101 having no password

this could be the computer trying to boot off a USB device plugged into the computer.Check that you don't have any USB devices plugged in. and no CD in the drive. then reboot the computer.

The first thing I would check is the heater control valve. This valve opens when you turn the inside control to heat and allows hot coolant to enter the heater core. If coolant doesn't enter the core, you don't have heat.

This valve is usually located under the hood behind the engine up close to the firewall. It will have coolant hoses attached to it. There should be an arm on the valve with a cable from inside the vehicle attached to it. This cable causes the arm to move, opening and closing the valve. Have someone inside move the heater control and watch this valve for movement.

During the warmer months, this valve is not being opened and closed, and it can get stuck. Moving the arm a few times will probably get it working again.

You'll have to open up the PS3 with a T9 hex security screw driver, then you'll have to open the blu-ray drive up.

Check youtube for tutorials on it.

By visiting this http://www.ip-details.com/internet-speed-test/ you get your ip-address.