Question about Maytag Performa PAV2200

1 Answer

Maytag performa washer hot/cold cycles reverse, hooked up correct

My maytag performa washer hoses are hooked up correctly but when it is set on cold it puts out hot water, when it is set on hot it puts out cool/warm water. the cold rinses are hot. this happens most of the time but not always.

Posted by timbo273 on

Ad

1 Answer

Bruce Canfield

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,776 Answers

This sounds like a cold water supply problem that's usually caused by a problem at the water inlet valve. First, remove the water supply hoses and check the small screens inside the water inlet valve. Make sure they are not clogged with rust or debris. Next, check the solenoids using a multimeter or ohmmeter. Check for continuity. A lack of continuity indicates a faulty solenoid and the water inlet valve assy will need to be replaced. I will attach a photo for reference. Hope this helps and best wishes.

maytag performa washer hot/cold cycles reverse, ho - ef00f33.gif

Posted on Aug 10, 2009

  • Bruce Canfield
    Bruce Canfield Aug 10, 2009

    The problem could also be a faulty temperature select switch. To test it you must check voltage at the water inlet valve while selecting different settings on the switch.

×

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Cold/cold cyle wash water not cold


try to do cold cycle first without doing warm cycle first

Apr 12, 2008 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Maytag Atlantis Washer - no cold water


Check the solenoid valves. If it's connected to hard water, the minerals build up inside and won't let the internal plunger move.

Mar 16, 2017 | Maytag Atlantis MAV9501E Top Load Washer

1 Answer

Maytag Epic Z Washer F-20, Water Inlet replaced, still F-20 Error


Chris an F-20 is usually a clogged filter on duet washers. Did you go by the tech sheet in your machine? It gives the codes and remedys and is in a jacket behind the kickplate which you remove to get to the filter. You will need a quarter inch nutdriver to gain access.
SERVICE MANUAL is HERE on my manual page






If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

Dec 07, 2012 | Maytag EPICz Electric Dryer

1 Answer

I have set the rinse cycle set to cold on our washing machine, however the clothes are rinsed hot, when I take the clothes out of the washing machine after the cycle is complete they are hot. How do I...


the hoses may be reversed...select cold rinse and turn on washer...if its hot..then try cold wash, is it hot? then try hot wash...is it cold? if so, check your hoses are on correctly....reverse hose's

Jan 23, 2011 | Kenmore Washing Machines

1 Answer

Cold/cold wash uses hot water wash and warm rinse. I have t set to hot/cold wash to get cold water wash.


probably the water inlet hoses are hooked up cold water line to the hot water inlet and vice versa

Aug 21, 2010 | Maytag Neptune MAH5500B Front Load Washer

1 Answer

Why doesn't cold water flow into the washer through the Smartwater filter? When my Maytag Performa's Wash/Rinse temperature dial is set on Cold/cold no water flows into the tub. But when I set it on...


Hi .. I would first check the supply valve at the washer to be sure that it is open. if it is open , you can check the flow by shutting it off, removing the supply hose, opening the valve slowly and observing the flow. You might need a small bucket here. If you have water flow here at the washer supply valve, then the problem is inside the washer control.

Apr 18, 2010 | General Electric GE SmartWater Household...

1 Answer

Maytag Performa wont fill hot water


The water fill valve - The water fill valve is a mechanical and electrical part, the coils on the valve need electricity to mechanically open the valve to allow the water to flow into the washer....myth....the washer pumps water into itself...no, it does not. The fill valve opens and the house water pressure pushes the water into the washing machine.
No cold water or no hot water - The fill valve has two coils, one for the hot water and one for the cold water. It is possible that one of the coils can fail and you loose that filling ability. If the cold water coil quits, the hot will still work and during warm fill you will get hot water only and during a cold fill you will get no water at all. If the hot coils quits, you will still have cold water fill, cold water only on a warm setting and no water on a hot fill setting. You can No cold water or no hot water - The fill valve has two coils, one for the hot water and one for the cold water. It is possible that one of the coils can fail and you loose that filling ability. If the cold water coil quits, the hot will still work and during warm fill you will get hot water only and during a cold fill you will get no water at all. If the hot coils quits, you will still have cold water fill, cold water only on a warm setting and no water on a hot fill setting. You can test a fill valve live for 120 volts, power to a fill valve coil and no fill = a bad fill valve. You can also test the coils for continuity, no continuity = a bad fill valve. Some Maytag washers have a fuse in the fill valve circuit, if this fuse let go the washer will not fill. Fill valves can also from time to time stick open and not stop filling. If you have to shut off the fill valves to stop the water from filling in the washer, you have a bad fill valve and you will have to replace it.

Nov 27, 2009 | Maytag Performa PAV2200

1 Answer

Warm water filling up washer, with no hot water hooked up to wash


exactly
it will maintain 60 degrees but cycling hot cold

thermistor

Sep 29, 2009 | Maytag Performa PAV2200

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

787 people viewed this question

Ask a Question

Usually answered in minutes!

Top Maytag Washing Machines Experts

John Tripp
John Tripp

Level 3 Expert

4656 Answers

Brad Brown

Level 3 Expert

18378 Answers

jdthefixer

Level 3 Expert

746 Answers

Are you a Maytag Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...