Dryers Logo

Related Topics:

Question about Kenmore Dryers

Open Question

I have a kenmore he5t dryer. I think the start button is bad. What is the fix?

Posted by Kyle Sikes on

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1helpful
1answer

Kenmore elite he5t washer model 11047789701 flashing F01 fault code- does this mean ccu must be replaced?

Do not take this as definitive answer! I am not an expert. A F01 error is indicative that the Central Control Unit cannot get instructions from the EEPROM. If you have not already done so, unplug the washer for a full 2 minutes to clear any instructions in memory, then plug it back in. If you still have a F01 error I suspicion that it is a bad CCU board. You can try to run the diagnostic on page 8 of the service manual but I do not think it will run if it is a bad CCU board.
0helpful
1answer

He5t tearing clothes

Are you sure that the clothes are not getting caught on exposed zips.

Why not load some things like towels sheets (without zips/buttons etc) in the washer and see if the issue repeats itself. You should also be able to see if there are any sharp edges or loose sharp items in the drum (mind your fingers)
0helpful
1answer

I have a 2002 27" kenmore elite gas dryer that runs great except you have to hold down the start button. I took it all apart and cleaned it. The motor looked fine. I think it might be the start button.

Normal 0 MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman";} Hi,

There can be many reasons why your dryer will not start or turn...

The most common causes are the belt breaking or jumping off, or the motor going bad...

Here are a couple of tips that I wrote will help you to figure out why your dryer will not run...

Dryer Repair - The Dryer is not Turning

Dryer Repair - The dryer will not start


heatman101

0helpful
1answer

I have a kenmore he5 electric dryer. We have

I am having the same problem. I think there is a design problem. They have tried to fix mine 3 times (replacing the dryer with a new one on the first try!) My dryer is only years old. I'm so disappointed with Sears and Kenmore.
1helpful
2answers

My Kenmore dryer "Start" button does not stay depressed.

a complete model # from inside the door would be helpful, on wost dryers when this occures the motor is packed with lint so the sentrifisle switch cant move from the pastion to the run or the switch on the motor itself is bad, the run windings in the motor could be bad. some of thethe more complicated dryers have a relay on their control board than burns out. try blowing out the motor with compressed air or the blow end of a shop vac use the skinney attat. to concentrate air
0helpful
1answer

My kenmore he5t washer will not turn on. The on

I have the same problem . If I power cycle mine enough times I eventually get a F70 or F71 code. My research online suggests that the user interface board has a problem and needs to be replaced.

The good news is the warranty covers these boards for two years. The bad news is they are $360 if you are out of warranty.

HTH
Jun 12, 2009 • Kenmore HE5
0helpful
1answer

How do I prep my Kenmore Elite He5t washer for move to new house

Washers n dryers usually require some balancing after a move to the new area, and when you lift the washer on a dolly, you lift it from the rear. Assuming you've already tipped the washer slighlty to one side, checked the bottom for which side has the most metal underneath. This is best done with 2 people. Do the same with the dryer. The braces are used to help balance or to keep from tipping when the machine was packed inside a large box.
0helpful
2answers

New HE5t steam dryer will not turn on

What was wrong with your dryer? I am having that same problem?
0helpful
2answers

Electric kenmore dryer

replace the motor it is stuck in the start winding and can cnot get up to the run winding as long as you are holding in the start button the start winding is working in a second it should through the motor switch shift the voltage to the run winding
bad motor switch
replace switch if available or change motor
Not finding what you are looking for?

140 views

Ask a Question

Usually answered in minutes!

Top Kenmore Dryers Experts

Marvin
Marvin

Level 3 Expert

85241 Answers

Brad Brown

Level 3 Expert

19166 Answers

Mike

Level 3 Expert

4383 Answers

Are you a Kenmore Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...