Question about Samson Audio Players & Recorders

Is there a way for fuse replacement for Samson Resolv SE6?

3 Related Answers

Anonymous

2 Answers

SOURCE: Samson Resolv 65a monitor repair

Its prob a dry solder joint problem.

http://www.gearslutz.com/board/low-end-theory/314545-samson-rubicon-r5a-problem.html

Posted on Sep 16, 2010

Hi mastervideo,
If you are going to get the voltages reading of the speaker terminal, set your multimeter to AC not in DC. You will get a maximum 12vac depends upon the strength of the input signal and your volume control. The reading will flactuate depend upon the input signal.
Hope I helped you.
Have a nice day!
Thanks for using Fixya.

Posted on Apr 05, 2011

Paul Smith

1 Answer

SOURCE: Hi There the fuse just blew in one of my Samson

Hi , where is the fuse in my resolve 65a ? i just cant find it.

Posted on May 03, 2014

Add Your Answer

Upload

Upload an image from your computer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

Loading...

Include an image. It's worth a thousand words.

prev next

Related Questions:

1 Answer

Samson 65a: power good, speakers good , LEDs lit, no sound at all?

Check and replace the damaged component/s at its audio output section circuit board. If needy, replace this board as card basis. If you wish to get some details; check the site linked here. Pull up older posts. Search the site by type in the "brand name" to your device; in the "Search box at the top right of the display window of the Homepage" to get gathered related posts.
http://electronicshelponline.blogspot.com/

Oct 11, 2016 | Samson Resolv 65a Main / Stereo Speaker

1 Answer

I need a transformer for my resolv 65a monitor

Are you an experienced tech? In most cases (unless there is a defect in manufacturing) transformers are not a common cause for failure. If it blows the fuse disconnect the secondaries and see if it still blows the fuse. If it does then the transformer is likely the cause, if the fuse doesn't blow then the problem is elsewhere. If you have 120vac at the primary and nothing(or very low) at the secondary(s) then the transformer could also be at fault. If you have done this already and narrowed it down to the transformer, sorry I cannot help. I used service Samson but no longer am able to get parts. Good luck!

Jan 04, 2015 | Samson Audio Resolv 65a Active Studio...

1 Answer

One of the woofers blew out. Where can I get a replacement?

Please contact by mail describe haw many oHm of subwoofer, active or passive it? may be we can help w/ replacement subwoofer [email protected] hotmail.com

Jun 11, 2014 | Samson Resolv 65a Main / Stereo Speaker

1 Answer

Samson Resolv 40A,no sound, power light on cables good.

Your best bet is to take them to an authorized repair center. You may also want to talk to Samson directly. Here is their support link-
Support SamsonTech

Mar 19, 2013 | Samson Resolv 40A Monitor Speakers

1 Answer

65a Resolv studio monitors. The left one just blew out -- maybe. The blue LED stays dim, as though the monitor has been sleeping. When I power off the monitor, the speaker gives a loud pop, and the cone...

You are getting DC offset voltage on one of your amplifiers that is the reason the speaker pushes out and you might be hearing a humming noise too. Do not turn on the speakers till you get it fixed or else you would end up burning the speaker voice coil too.The dim blue LED is also an indication of a short circuit in the output stage.
Your left amplifier needs a output chip (IC ) replacement. You will need professional help to do that. Will cost you about 20$ plus service charges.

Jun 27, 2011 | Samson Resolv 65a Main / Stereo Speaker

1 Answer

Tweeter is cutting in and out

need to open up speaker and check connections on tweeter. Check closely on tiny wires from magnet(voice coil) to paper cone

Jan 04, 2011 | Samson Resolv 65a Main / Stereo Speaker

2 Answers

Hi There the fuse just blew in one of my Samson

Hi there
To answer your question;
If it is not indicated near the fuse holder then look closely at the metal end caps of the fuse.
The value will be written on one of them,
It may look like 2A/250v for 2amps.

Hope this help
Cheers

Jun 14, 2010 | Samson Resolv 65a Main / Stereo Speaker

1 Answer