Question about Amana Washing Machines

Open Question

Amana NTW4651BQ1 washer. Only making a "draining" noise, no lights, no lid lock, no nothing

Posted by Patricia Marie on

Ad

5 Related Answers

Anonymous

SOURCE: Door Lock Clicks/Makes noises Washer does not agitate/spin

Sounds like very worn motor brushes to me, as its trying to turn the drum but has'nt the power needed to maintain any momentum,and the blinking door light is because of the bad cotact from brushes to motor.About £20 for a set of brushes or get an engineer to fit new brushes,but get a price first.

Posted on Apr 19, 2007

Ad

Dov Dror

  • 641 Answers

SOURCE: Kenmore Model 27032 lid problems

Look for the lid switch and press on it manually. Let me know if it will operate the machine.

Posted on Sep 12, 2007

Ad

Anonymous

  • 52 Answers

SOURCE: washer won't drain. Makes grinding noise

check your water pump. there maybe something in it. If there is you may have to replace the pump

Posted on Nov 06, 2009

tbirdfan1

Michael Thomas

  • 3056 Answers

SOURCE: amana front load washer error code "nd". Door is

Hello there and welcome to fixya
From what you're describing it sounds like the drain pump is blocked. The nd error code indicates "no drain". If the unit can't drain it won't spin. You're going to have to slide the washer out far enough to remove the rear panel; be careful not to damage the floor. Once you get the rear panel off you will see the pump. Be sure to have plenty of towels & a small container to catch water. I am sending you instructions from the service manual to remove and replace the pump. Another possibility is the drain line is blocked or something is stuck in the tub to pump hose.

Posted on Nov 05, 2011

Phil Gallagher

  • 18 Answers

SOURCE: how to add fabric softner to the amana washer with locking lid

Check and see if there is a cup in the top of the agitator. Some machines have you put it there, turning back and forth during wash doesn't bother it, but the spin to empty the wash water causes the softener to go out through slots in the top of the cup and be held in the agitator. when it stops the softener drains into the tub, ready for the rinse cycle.

Posted on May 30, 2012

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Amana NTW475OYQ1no lights or sounds. Verified power @circuit board. Someone closed lid on a shirt earlier that preventing lid to I open.verified switch waz working and the wife did a load of laundry.


Admiral, Whirlpool, Maytag - Washer Repair - Not ... - YouTube

? 5:51
https://www.youtube.com/watch?v=oBihToN6dxs
Sep 6, 2013 - Uploaded by ApplianceVideo.com
Troubleshoot your Admiral Top Load Washer that has these following ... Speed Queen, Amana Whirlpool ..... Lid lock lightflases; no spin cycle.

Amana Washing Machine NTW5400TQ1 Troubleshooting ...

www.repairclinic.com/.../Washing-Machine...-/Amana-Washing-Machin...
Amana Washing Machine NTW5400TQ1 Troubleshooting & Repair Help. Amana Washing Machine problems. Washer won't spin · Washer is making loud noise ...

Jan 16, 2016 | Amana Washing Machines

1 Answer

WASHER ... COMES ON GREEN SENSING LIGHT STAYS ON START'S TO FILL CLICK'S OFF RED DOOR LIGHT LOCK LIGHT COMES ON STAY'S BLINKING


Thank you first person that has provided a model number sounds like you already changed the lid lock assembly if you did you know how to get the top up inside the front panel is a tech sheet it will tell you how to place the unit into diagnostic and read the lights for an error code recheck your connection at the control board a flashing lid lock would should give and F5E1 or F5E2 error code also check the alinement of the tab on the lid where it goes into the lock assembly should be a smooth transition

Jan 12, 2015 | Amana NTW4501XQ 3.4 cu. ft. Top Load...

1 Answer

Unlocking your washer so it actually works.


If the green cycle light is flashing on then off, this usually means the cycle is paused. The lid lock should unlock when in pause mode, if not you will need to press and hold the "Pause/Play" button to clear the cycle completely, if there is water in the unit, it will drain first, then unlock the lid and be on standby to start a new cycle. Pleazer Appliance...

Apr 13, 2014 | Amana NTW4700YQ Top Load Washer NTW4700YQ

1 Answer

Amana washer lid lock wont quit blinking


Your washer lid lock button is locked and lid was not put down before it locked, which is why the light is flashing. Therefore, push the "START" button until you see the lid lock button is off (Approx 3 seconds). Once it is off, then you can put the lid down and push the start button again, which will lock the lid into place. The washer will NOT drain or wash or spin unless the lid itself is in the locked position. If you were able to get the lid down and locked and it still doesn't work, then you need a technician to replace a wiring harness. However, you mentioned that the lid lock button was flashing, therefore, it stands to reason that your lid is NOT locked down.

Apr 13, 2014 | Amana NTW4700YQ Top Load Washer NTW4700YQ

1 Answer

Maytag centennial washer


When lid lock flashes, that is an indication of a bad lid lock in some of the mvw washers.(depending on your unit and model number &error codes)

Nov 03, 2013 | Washing Machines

1 Answer

Why wont my amana washer start at all?


My washer will notwork it will not let the lid lock are fill with water

Jan 20, 2013 | Amana NTW4501XQ Top Load Washer

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

96 people viewed this question

Ask a Question

Usually answered in minutes!

Top Amana Washing Machines Experts

Michael Thomas
Michael Thomas

Level 3 Expert

3056 Answers

Mike

Level 3 Expert

4372 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Are you an Amana Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...