Question about Laser Office Equipment & Supplies

1 Answer

How i can resolve fuser error laser jet pro 400

Posted by m shahbaz ali on

Ad

1 Answer

Randy Schumann

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 410 Answers

A fuser error is probably caused by a thermistor (detects an overheating problem). The fuser is probably best serviced by the manufacturer as an improperly serviced fuser could lead to a fire.

Posted on May 30, 2019

Ad

5 Related Answers

Anonymous

  • 1142 Answers

SOURCE: Fuser Error 50.1 Fuser is hot. What is a fuser?

error 50 means your fuser assembly has gone bad or its not getting power to be functional. you need to replace the fuser unit.

Posted on Aug 17, 2008

Ad

Anonymous

SOURCE: nedd fuser diagram for the hpcolor laser jet 2600n

Replace fuser assembly

Posted on Apr 04, 2009

Anonymous

  • 25 Answers

SOURCE: Fuser Error 50.1 Fuser is hot. What is a fuser?

MAKE SURE THE PRINTER IS OFF AND INPLUGED BEFORE YOU START! The fuser is located in the back of the printer. You should see two blue pads where your index finger and thumb (on both hands) should pinch together then pull the fuser out. Re-seat the fuser back into its original position and wait 20 minutes before turnging Unit back on. If you do not wait 20 mins then the 50 error will appear again even if the problem is fix. Once you wait 20 minutes and it still gives you a 50 error you must replace the fuser. I have a great place to purchase fuser so let me know if you nee contact info!

Posted on Jul 16, 2009

Anonymous

  • 1 Answer

SOURCE: HP Laser Jet 2840 50.2 Fuser Error

Usually this means that the fuser is not heating to the correct operating temperature. Remove the fuser and check all contacts. Be careful it can be very hot. Always let it cool down for atleast 30 minutes before touching the face of the fuser. After you check it over and clean off any contacts, reseat the fuser back into the printer. Plug it back in and turn the printer on. If this doesn't work and you still get the error, the fuser needs to be replaced.

Posted on Oct 09, 2009

blenderbobby

  • 1 Answer

SOURCE: Fuser Error 50.1 Fuser is hot. What is a fuser?

I think the fuser is in your **** part. This problem can be corrected by sitting in a tub of salt water. Make sure the printer is plugged in and is powered on. Is the display lit? If it is place the printer in the tub of water you are sitting in. You sould now be able to realize nobody cares and it no longer matters

Posted on Nov 29, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hp laser jet pro 400 m401 printer 59.A0 error


SOURCE:HP color laser jet printer is displaying error
Developing disengaging motor error. Run the component test to verify that
the print developing disengaging
motor is working correctly.
. Reconnect the connectors J468 and
J1020 between the developing
disengaging motor and the DC
controller PCB.
. if motor is not rotating Replace the developing disengaging
motor.

or
problem due to cairtage leaver lock cairtages not engage properly i hv found max problem of this leaver it found damaged due to improper opening the doorpls follow
above steps if problem not resolved then call hp engr for 4th step.
I Hope It Works.

Sep 15, 2017 | HP Office Equipment & Supplies

1 Answer

HP LaserJet Pro 400 M401DN Laser Printer keeps jamming at cartridge.


Is the paper stopping just at the cartridge or is it in the fuser. We have had a few of these fail with bad fusers. The only time we have had a cartridge issue is if the drive shaft on the right side of the cartridge falls off.

Sep 14, 2016 | HP LaserJet Pro 400 M401DN Laser Printer

1 Answer

Hp laser jet 300/400 10.1000error


10.10 error means it does not recognize the chip on the cartridge or that the seal is still in cartridge need new cartridge

Feb 24, 2015 | HP LaserJet Pro 400 color M451dn - Printer...

1 Answer

What is the solution for fuser error 50.4 in laser jet pro 400


Most likely you will need to replace the fuser. Try plugging the printer in to a different outlet than it is right now. If you get the same error then you can be pretty sure the fuser is bad.

Feb 20, 2015 | Laser Office Equipment & Supplies

1 Answer

How do you fix a 59.3 error


59.3 indicates the fuser motor is not starting up.
This usually means the fuser motor needs replaced.

Part Number RM1-8609-000CN

Mar 13, 2014 | HP LaserJet Pro 400 color M451dn - Printer...

1 Answer

My printer hp laser pro 400 show message 50.3 fuser error


hello ,,

50.x Fuser Error

Description
The product has experienced an error with the fuser.
Recommended action
Turn the product power off, wait at least 30 seconds, and then turn the product power on and wait for it to initialize.
Turn off the product, wait at least 25 minutes, and then turn on the product.
If you are using a surge protector, remove it. Plug the product directly into the wall socket. Turn the product power on.
If the message persists, contact HP support.

Oct 21, 2013 | HP LaserJet Pro 400 M401DN Laser Printer

1 Answer

Fuser error


Directly form HP's website:
50.2 Fuser Error Turn off then on
Error message 50.2 Fuser Error Turn off then on Description 50.2 Slow fuser error. The device has experienced an internal hardware error. Action
  1. Turn off the device, wait at least 25 minutes, and then turn on the device.
  2. If a surge protector is being used, remove it. Plug the device directly into the wall socket. Use the power switch to turn on the device.
  3. If the problem continues, contact HP Customer Support Center for technical assistance

Feb 08, 2012 | HP Laser Jet Pro CP1525N

1 Answer

I have a hp laser jet P 3015 he display the error fuser error 59.1 how to resolve the problem


The error means that there is a motor startup error. Try to:

1. Turn the printer off, and then turn the printer on.
2. Check and reset the fuser and toner cartridge to make sure they are not hindering gear movement in the drive train.
3. Check the main motor's cable to ensure that it is seated properly.

If the error persists, replace the main motor.

Dec 29, 2010 | HP Office Equipment & Supplies

Not finding what you are looking for?
Office Equipment & Supplies Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Laser Office Equipment & Supplies Experts

CheckitRight
CheckitRight

Level 3 Expert

1363 Answers

Barbat Nae
Barbat Nae

Level 3 Expert

509 Answers

Scott Kalvinek

Level 2 Expert

56 Answers

Are you a Laser Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...