Question about Radio Communications

1 Answer

On Alnico DJ-175T how can I turn off Repeater operation when in VFO mode

When in VFO mode pushing PTT produces a Freq. that is 600 up or down! How can I prevent this ?

Posted by haasent on

Ad

1 Answer

Clint Millett

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Habit-Forming:

    Visited the website for 3 consecutive days.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 97 Answers

Hi. Google has the user manual at: blob:https://www.cleancss.com/723b15cc-34cb-4c4b-aec6-e3db91bc4499

The info you are looking for is in section 4. Basically you press the shift key to do want you want.

Good Luck.

Posted on Jun 04, 2019

Ad

4 Related Answers

Steve

  • 3289 Answers

SOURCE: yaesu ft 50r

The FT-50R is an extended receive, but dual band (UHF & VHF) amateur transceiver. It is capable of transmitting between approximately 144Mhz - 148Mhz VHF and 430Mhz - 450Mhz UHF.

Typically, the radio will provide an audible warning whenever attempting to operate outside of its intended range(s). The manual has a section on maximizing battery life, and can be downloaded below:

http://www.radioamateur.eu/schemi/FT50_user.pdf

Posted on Sep 21, 2009

Ad

Kazimierz

  • 24 Answers

SOURCE: My Motorolla GP 68 changes to a differant freq.

You have ON the frequency shift in your GP Motorola

Posted on Apr 25, 2010

ginko

Ginko

  • 19396 Answers

SOURCE: My TH79A keypad does not

Hi.

It looks like the key panel is defective and must be replaced. Standing to your description the receiver is working. Here the biggest third party part seller. Call them and find out if the panel listed in parts includes the key pad.

Kenwood has no parts for old model. If Partstore does not have the spare, try Kenwood, or look for second hand parts on Ebay.

Regards.

Ginko.

Posted on Mar 31, 2011

em_snf

bayu

  • 2 Answers

SOURCE: my alinco vhf fm transceiver DJ 195

check your ht cpu,the cpu is the biggest chip,usually it located under led display

Posted on Jun 29, 2012

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Menu mode 075 will not change the power settings


What freq and mode are you in? Did you lock out the vfo knob? Are you on a band that you can transmit on? More info please

Mar 17, 2016 | Yaesu FT-857D transceiver

2 Answers

What's is the rep +100 in the vfo programming list?


What is the manufacturer,make and model number of your radio?

Mar 16, 2015 | Radio Communications

1 Answer

I need help programming my baofeng 997s


To programme a repeater. VFO mode & curson on top line of display. Enter freq eg 147.250. Go menu button change settings like offset, tone. In menu delete channel required eg 000. In menu below that, choose mem channel now 000 & it saves receive freq.

Exit. press *SCN button so R appears on display. Save as 000 again but this time it stores TX freq. In other words, you save RX first, then exit.Add * so R appears in display second time round and save again TX freq. Go to channel mode and see it is in 000.

I might do a video to help people. Its the same process with UV5r and other Baofeng. Simplex you just save in one operation because TX is RX.

Aug 08, 2014 | Radio Communications

1 Answer

How do I program a yaesu ft-270?


I will be working from the online version of the manual located here. It may or may not be the same as your printed manual included with the radio - so you might want to download this copy.

First, let's set the radio to automatically set up repeater input shift based on the published receive frequency. By default, the 270R will transmit 600Hz up or down as determined by the band plan. This feature is called ARS and can be disabled if desired. If it does not display a frequency 600Hz up or down from the receive frequency while transmitting, is has been disabled. Let's re-enable it by performing steps #1 thru #5 on page 19 of the manual. Once completed, the 270R will automatically shift the transmit frequency (to match the repeater input frequency) as shown in the top half of the "ARS-Repeater Subbands" graphic at the bottom of page 19. The bottom half shows the export version of the shifts and does not apply to USA versions. If you have "odd splits" (repeaters that have input frequencies that are non-standard ie: other than 600Hz; or shift up instead of down and vise-versa) you'll need to manually change these later as described in VHO Split Mode on page 21. Any repeater operating on 147.000Mhz may have a shift either UP or DOWN. As you can see in the graphic, 147.000 is between the (-) and (+) shift so it could be either direction. Double check to make sure the radio matches the shift that the particular 147.000Mhz repeater you wish to access requires.

Next, create a list of repeaters that you wish to save in memory (you can check online databases to obtain the most recent information). This list should include Name, Receive Frequency, any non-standard direction or value Shift (called "odd splits), Tone Type and Tone. The name should be 6 or less alpha-numerics in length and be something that helps you identify it . This could be the name of the repeater owner: "TIM, PETE, etc. ", the name of the club that runs it: "BARC, CMARA, etc.", the city or town it is in: "BOSTON, OAKLND, etc,". You might run into names that would create duplicates when there are more than 1 repeaters there in the same location. Boston has several 2M repeaters - naming them BOSTN1, BOSTN2, etc. may help you remember them, but it will be easier still to append the decimal portion of the frequency to remember - such as in the case of a Boston repeater on say, 146.030Mhz and one on 145.150. BOS030 and BOS150 would probably be easier than trying to remember which is BOSTN1 and which is BOSTN2. Placing the names in the 270R memory is the last thing done, so don't worry too much about a name for the 270R's display just yet.

Most repeaters use CTCSS for access. Some newer repeaters use DCS. Some require or even prefer that no tone be sent at all. CTCSS is an analog frequency and a DCS code is digital data. The repeater may require one or the other to be present to "wake up" and begin retransmitting your message. All you really need to know about these two systems is the you need to match both the tone type and the tone value to successfully activate the repeater. Set the radio to your desired default power output level. Tap the VFO button once to enter VFO mode (if not already in VFO mode).

Enter the repeater's receive frequency by twisting of the tuning dial (page 13) or by direct entry (page 14) via the keypad. When using the keypad, do not enter the leading "1" of the frequency - as all the frequencies that this radio can tune begin with "1" and can not be changed. With the repeater frequency displayed, next enter the CTCSS tone for the repeater as described on page 23. If the repeater uses DCS, follow the directions that begin 1/3 of the way down on page 24 instead. As far as "TONE" and "TONE SQ" are concerned, the difference can best be described in that a radio working on a repeater system benefits from use of TONE, and a radio working on in simplex operation (no repeaters) benefits from the use of TONE SQ. Since we're programming repeater frequencies, there's no need to select TONE SQ. If the repeater strips the tone from its output, your radio will remain silent if set for TONE SQ. TONE is a much better match for our needs. Remember, you must use the DIAL to select the CTCSS tone frequency or DCS Code. Unlike the repeater receive frequency, it is not possible to directly enter the tone frequency or code via the keypad.

At this point, the radio should be displaying the recieve repeater frequency. Since automatic repeater offset is enabled - the 600Hz offset frequency and direction are set. The tone type and value for this repeater frequency have just been set in the previous paragraphs as well. Now it is time to write all this information to the radio's memory. This is detailed 1/3 of the way down on page 29 under "Memory Storage". Once you have performed step 5 in Memory Storage for this first repeater, it says to repeat this same process. This means setting the next repeater's recieve frequency, tone type and tone value - just as you have done with the first.

Once you have made sure that you have unique names assigned and the other information above, you are ready to begin adding them into the 270R's memory. You can go back add names to be displayed instead of the frequency of the repeaters if desired. Page 31 details the procedure to assign an alpha numeric name to each memory location. Make sure that you are assigning the correct alpha-numeric to the repeater by checking the frequency from time to time - don't blindly add alpha-numerics to memory channels.

This is a very tedious process. Ham Radio Outlet offers Windows programming software and transfer cable by Yaesu called "ADMS-270" for $38.95. This package allows you to easily create many lists of memories on your Windows PC & keyboard that can be uploaded and downloaded "on the fly" I highly recommend this software - or any software that allows you to program the radio from a computer rather than the radio itself.

I hope this was helpful.

Nov 29, 2012 | Yaesu Ft-270r Vhf Ft 270r Ft 270 R

1 Answer

I use this to track my hunting dogs. I forgot how to program my numbers in though. Ex. 217.105


1. Select VFO mode and receive mode
2. Enter freq, including decimal point
3. Push ENT

Need the manual? You can download and print it, at no cost, here:

http://mcars.us/Manuals/IC-R10.pdf

Bill B.
Listening in since the 60's

Oct 14, 2010 | Icom IC-R10 Handheld Scanner

1 Answer

CLS 1110 Programming


Not certain what order you are doing it, so I will type a brief explanation:

With the radio turned OFF, hold in the PTT and the MON, while turning the radio on. Continue to hold the PTT and MON until the radio stops making noise. You are then in programming mode and can use the menu button to walk through the stages of programming.

Mar 23, 2009 | Motorola CLS 1110 (1 Channel) 2-Way Radio

3 Answers

HT 1000, MT1000, Radius P110 Tx problems


Sorry about taking so long to respond. These radios have worked properly in the past. They have increasingly become worse to the point they will not Tx. I have tried to com-cate with a good radio but unsucc. I'm thinking the Tx freq has been altered? Can one freq (Tx) be altered and not the other (Rx) or will both become altered?

Oct 04, 2008 | Motorola HT1000, MTS2000, MTX8000/9000...

1 Answer

Yaesu ft 50r


The FT-50R is an extended receive, but dual band (UHF & VHF) amateur transceiver. It is capable of transmitting between approximately 144Mhz - 148Mhz VHF and 430Mhz - 450Mhz UHF.

Typically, the radio will provide an audible warning whenever attempting to operate outside of its intended range(s). The manual has a section on maximizing battery life, and can be downloaded below:

http://www.radioamateur.eu/schemi/FT50_user.pdf

May 25, 2008 | Yaesu NABC NABC LMR NICD BATTERY FNB-V47...

1 Answer

Kenwood TK370N UHF FM HANDHELD RADIO


By keeping the PTT button pushed, if you get a rapid beep and the red led is blinking, sounds like a bad battery. Batt voltage is a nominal 7.5v. anything lower than 6.25v and the low battery beep starts. A rapid beep, and no red led blinking, an error in the transmit freq.

Mar 01, 2008 | Kenwood Radio TK 260 360 270 370 2100 3100...

2 Answers

Please Help me


MOTOROLA GP-2000 Programming Instructions
Switching between Dealer and User Configurations

- Turn off radio
- Press PTT + Monitor Buttom and + buttons together and turn radio on
- LCD Displays PRO-CLR
- To confirm switching to Dealer configuration, Press PTT. To cancel, press any other button
- Turn off radio. The radio now operates in Dealer configuration
From Dealer to User

- Turn off radio
- Press PTT + Monitor Buttom and + buttons together and turn radio on
- LCD Displays PROTECT
- To confirm switching to User configuration, Press PTT. To cancel, press any other button
- Turn off radio. The radio now operates in User configuration
ENTERING PROGRAMMING MODE
If the radio is turned on, turn it off. Press and hold the MON button and turn the radio on. A ringing tone will be heard,which indicates that the radio is in Programming mode. The PW and [] indicators are displayed.
EXITING PROGRAMMING MODE
To exit programming mode, turn off the radio
ACCESSING PROGRAMMING MODE PARAMETERS
In dealer config., Programming mode parameters are grouped into 3 (three) main categories.

RW = Radio Wide
Channel (001 to XXX) and
VFO (Variable Frequency Operation)

User + or - buttons to move from one category to another.

RW < >CH 001 < > CH 002 < > …. < > CH XXX < > VFO
Note : Radio operating in User Configuration is only restricted to PW parameters

Once you have selected the category and wish to view its parameter, use PTT or MON to move from one parameter to another.

Nov 06, 2007 | Radio Communications

Not finding what you are looking for?
Radio Communications Logo

Related Topics:

146 people viewed this question

Ask a Question

Usually answered in minutes!

Top Radio Communications Experts

eradiostore
eradiostore

Level 3 Expert

1664 Answers

Brad Brown

Level 3 Expert

18564 Answers

Tom Chichester

Level 3 Expert

61177 Answers

Are you a Radio Communication Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...