Question about Pool & Spa

Open Question

Magnetic Impeller for saluspa bestway pump I need to replace it .

Does anyone know where I can get a magnetic impeller for a saluspaspa hot tub?

Posted by Anonymous on

  • Anonymous May 14, 2019

    Where can I get one

×

Ad

1 Related Answer

gotgeek2

Bob

  • 565 Answers

SOURCE: Pondmaster mdl 24 Series magnetic

The bearing needs to be pressed onto the ceramic shaft before inserting the impeller into the housing. Then it just drops in (while trying to hold on to it the best you can to keep it from slamming in.). New bearings didn't come with the new impeller? If not you will have to carefully pry out the old bearing from inside the housing.

Posted on Aug 19, 2010

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi, please explain to me how does this pump work? I have removed it from the LG washing machine. When I turn the rotor blades, it's not running continuously but it turns half way and stops. why>


The pump impeller will not spin as you think it should, the impeller is connected to the rotor of the pump motor which has magnets fitted.
When turning the impeller by hand this will only give you one half revolution as the magnetic field stops the impeller from spinning around.
This is perfectly normal.

Nov 24, 2015 | LG Washing Machines

1 Answer

Great lakes hot tub humming sound


You either have a locked pump, impeller or stripped impeller on the pump shaft. Remove the jet pump assy and repair the pump and or impeller. You can also replace the pump assy.

Apr 30, 2014 | Holmes Products HM495-UC Humidifier

9 Answers

No water flow e90 fault code intex pure spa


Unplug the unit. The E90 code on the intex spa is due to a dirty water flow sensor. Remove the control panel and all the screw holding the casing on. In the white plastic piece on the discharge, top hose, you will see a silver nut with a black wire coming from it. That's the sensor. The black wire is plugged into a white wire, carefully unplug it and unscrew the sensor. Clean it good and blow out the hole it goes in. This will fix the code and you will be back in business!

Sep 27, 2013 | Intex 10x30" Metal Frame Pool w GFCI

1 Answer

Lay-Z-Spa pump impeller replacement


In order to find the proper replacement you will need to provide someone with the following information.
  • amps
  • voltage
  • discharge size pipe
  • suction size pipe
Rod
US Parts Center

Jun 01, 2013 | Home

1 Answer

Rotor Assembly Stuck in Drawer Cavity


This picture of the rotor shows two of the three clips that hold it in the washer tub. They protrude from the smaller tan disc sitting just above the red magnet subassembly. Normally, you would unlatch and remove the filter plate, then unlatch the rotor assembly by turning the larger tan disc (with the three arrow tabs) counterclockwise until it stops. Since the top of your assembly is broken off, you'll need to turn the smaller disc counterclockwise about 1/8 turn, so the clips can slide up through their slots. The magnets in the rotor also hold it down somewhat, but it should be possible to slide the rotor out by hand.

The rotors in my double dishdrawer were deteriorated to the point that the plastic around the magnets was crumbling. Note that although the plastic around the magnets is red in this picture, all 4 rotors I have actually seen have blue plastic encasing the magnets, similar to that used for the impeller. I suppose it is possible that your magnets have come completely loose, and are jamming the rotor in place, or that some other foreign matter is caught in the drain impeller at the bottom of the rotor. But there isn't normally any physical connection at the bottom of the rotor- the lower impeller spins freely to pump water out the drain.
2_23_2012_5_42_29_am.jpg

Jan 16, 2012 | Fisher and Paykel 24 in. DD603H W Built-in...

1 Answer

Pool pump wont prime when in pool mode, but will run in hot tub mode. Hot tub is 3 ft higher than the pool... is this a bad impeller? I think it may have run for a few hours without a prime , as I...


I assume that it pumps from/to the hot tub. If so, the pump is fine. Look for any air leaks in the piping/hoses from the connection in the pool to the inlet of the pump.

Gary

Aug 30, 2011 | Hayward 1.5 Hp Northstar High Performance...

1 Answer

The impeller has quite a bit of movement in the housing which is causing it to rattle around and make a lot of noise. Would replacing the impeller solve this or is the housing damaged?


The impeller is supported at both ends with rubber bushings the impeller shaft wears into the rubber and enlongates the hole this happens over time or if you run the pump dry often. The rubber parts are replaceable.

Apr 14, 2011 | DANNER Magnetic Drive Utility Pump 110 GPH

1 Answer

Pondmaster mdl 24 Series magnetic pump. re: Replacement impeller/magnetic shaft installation Question: What do I need to do to install the impeller ***'y into the pump housing to ALLIGN THE...


The bearing needs to be pressed onto the ceramic shaft before inserting the impeller into the housing. Then it just drops in (while trying to hold on to it the best you can to keep it from slamming in.). New bearings didn't come with the new impeller? If not you will have to carefully pry out the old bearing from inside the housing.

Aug 18, 2010 | Pondmaster Impeller & Magnet for Pond -...

Not finding what you are looking for?
Pool & Spa Logo

Related Topics:

344 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pool & Spa Experts

john h

Level 3 Expert

23515 Answers

David Spradling
David Spradling

Level 3 Expert

11795 Answers

rogerpaul3

Level 1 Expert

62 Answers

Are you a Pool and Spa Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...