Question about Olympus Cameras

Open Question

I need a manual for Olympus PSD 20 - Olympus Cameras

Posted by Nick Cariglia on

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How to resolve the problem with psd file?


If the file is corrupted, there's nothing you can do short of finding another copy of the file.

Sep 27, 2016 | Computers & Internet

1 Answer

My 1999 Pontiac Montana power sliding door on passenger side will not open. You can push the button and it will pop open like it's going to open but will not slide open. Any ideas?


The power sliding door (PSD) includes several interconnected electronic and mechanical components. Obtain a specific customer concern in order to efficiently diagnose and repair the PSD system. Begin diagnosis with a service writer. Ask the customer for as much detail as possible regarding the conditions under which a failure of the door was noticed. Always include the basic concern, such as "door reverses when closing". The following details might affect the performance of the PSD:
?€¢
Weather conditions, such as snow or heavy ice


?€¢
The van was parked on an incline.


?€¢
The van has been parked for a long time, which may cause a weak battery.

Refer to Power Sliding Door Customer Concerns for diagnosis. Verify that all of the mechanical components of the PSD are aligned and operating correctly before you begin diagnosis of the electrical system. The electrical components cannot operate correctly if the mechanical components are not operating correctly.
I just checked out a 1999 Oldsmobile Silhoutte yesterday , same set up there is a cable inside hooked to a motor that opens the door. The one yesterday had the cable hanging out the back of the sliding door , does yours ?
Does it open manually ? There are electronics involved , sensors ,switches , a module an a electric motor .
The power sliding door (PSD) includes several interconnected electronic and mechanical components. Obtain a specific customer concern in order to efficiently diagnose and repair the PSD system. Begin diagnosis with a service writer. Ask the customer for as much detail as possible regarding the conditions under which a failure of the door was noticed. Always include the basic concern, such as "door reverses when closing". The following details might affect the performance of the PSD:
?€¢
Weather conditions, such as snow or heavy ice


?€¢
The van was parked on an incline.


?€¢
The van has been parked for a long time, which may cause a weak battery.

Refer to Power Sliding Door Customer Concerns for diagnosis. Verify that all of the mechanical components of the PSD are aligned and operating correctly before you begin diagnosis of the electrical system. The electrical components cannot operate correctly if the mechanical components are not operating correctly.
The amount of force necessary in order to reverse the PSD depends on the position of the sliding door at the time of obstruction. The PSD action may not reverse if the following actions occur:

  1. The PSD starts to close.
  2. A gradually increasing force is applied on the sliding door in an effort to reverse the operation.
The PSD control module may interpret the gradually increasing resistance as a corrosive or dirty track. The PSD control module compensates for the gradual resistance on the sliding door by applying more power to the cable motor when closing the sliding door. In order to reverse the PSD at this stage of the sliding door travel, an abrupt and firm force is required.
The PSD control module operates in this manner in order to compensate for the wear over the life of the PSD. Over time the vehicle may experience the following conditions:
?€¢
A dirty track


?€¢
A corrosive track


?€¢
Ice build-up on the track (during cold weather)

The PSD control module is more sensitive to obstructions near the end of the sliding door close operation. The amount of force necessary in order to reverse the sliding door travel is less than when the sliding door started to close.
When the sliding door is within 2.5 cm (1.0 in) of the closed position, the door lock latch switch sends a signal to the PSD control module. The PSD control module determines that the sliding door is in the unlatched (ajar) position. This action causes the control module to apply full power to the cable motor in order to bring the sliding door to the fully closed (latched) position. The sliding door will close unless the force is greater than the cable motor at full power. The PSD control module de-energizes the cable motor and the clutch when the PSD control module receives a second signal from the door lock latch switch. The second signal indicates that the sliding door is fully closed and latched.
Power Sliding Door (PSD)
The power sliding door (PSD) provides built-in diagnostics. This assists the service technicians during troubleshooting.
The PSD has the following diagnostic capabilities:
?€¢
Diagnostic Trouble Codes (DTCs)


?€¢
Input/output tests



I jusatI

Apr 28, 2015 | Pontiac Cars & Trucks

1 Answer

I need a driver of olympus FE-20 digital camera


Here is the official link from Olympus website http://www.olympusamerica.com/cpg_section/cpg_support_product.asp?id=1392
You can download the driver for your Olympus FE-20 digital camera including the user's manual in .pdf form.

Dec 27, 2010 | Olympus FE-20 Digital Camera

1 Answer

I bougt an Olympus digital camera model FE-20 It came with 3 manuals, 2 french and 1 Spanish, No English Plese send Enlish Manual. Or mail to 1205-555 W 28 str, North Vancouver, B C V7N2J7


Hi,

You can download and print the instruction manual (English) for Olympus FE-20 digital camera in PDF format by clicking this link.

Adobe PDF Reader is required to view this manual. Download Adobe Reader

If you wish to purchase a printed copy of the manual, you can order it from the Olympus website by clicking here

Hope this helps. Thanks for using FixYa.

Oct 31, 2010 | Olympus FE-360 Digital Camera

1 Answer

Warning psd mg


hello there!
you must disassemble the camera and blow air aiming the ccd block area in the backside of the the lens with a duster spray by means :REMOVE THE LENS AND BLOW AIR FROM 20 cm distance,then reassemble the camera thoroughly and please do not use excessive force while doing it,mini DV camcorders are sensitive in handling ATTENTION qualified personnel only

Dec 20, 2009 | Panasonic AG-DVC62 Mini DV Digital...

1 Answer

Olympus DM-20 erase lock is on, how to undo it?


The voice recorder is in read only status - you will need to format the device to remove the lock (read only). Go to menu - to submenu and then run the format option. make sure all files have been downloaded as once device is formatted all files will be permanently deleted

Oct 16, 2008 | Olympus DM-20 Digital Voice Recorder

Not finding what you are looking for?
Cameras Logo

Related Topics:

57 people viewed this question

Ask a Question

Usually answered in minutes!

Top Olympus Cameras Experts

Steven Wander
Steven Wander

Level 3 Expert

595 Answers

Muntejaya Ginting
Muntejaya Ginting

Level 3 Expert

10422 Answers

Lee Hodgson
Lee Hodgson

Level 3 Expert

4810 Answers

Are you an Olympus Camera Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...