I need to find an outdoor sensor for my ACURITE weather station MODEL #02483.I have looked on your site as well as Amazon and have found some outdoor sensors but none that are for this Model#

Hi,

I'm seeing that product/brand on ebay and amazon, so you can reach out to sellers of the item on those websites and they should have the accessories that you need.

Thank you.

https://www.acurite.com/temperature-and-humidity-sensor-06002rm-592txr.html

Not found it so far but here is a book for a 1050 model, much of which is transferable. There is no Dr. Tech website per se where you can get support or download a manual. That means you would have to depend upon hobbyist/blogs or look up information in generic sites about factors in weather if you have a question. Here is a site where you might try some queries:

http://www.weather-watch.com/smf/index.php?topic=53707.0


http://site.ambientweatherstore.com/Manuals/wh1050.pdf

https://www.rakuten.com/prod/dr-tech-professional-wireless-weather-station-w-solar-transmitter/230818678.html

Here's the manual for the AcuRite Weather Forecaster. If it's not showing the outside temperature, make sure the A-B-C switch is set to match the display unit. Not doing so might be the reason it's not synchronizing and displaying the outdoor temperature. https://www.acurite.com/media/manuals/75077-75107-instructions.pdf

Make sure that all the batteries are good!!
This procedure outlines the typical process to pair the sensor and base.
Base Station Battery Installation
·Remove the printed vinyl label from the LCD screen of the base station
·Position the remote sensor near the base station
·Open the battery compartment at the back of the base station and insert (2) AA batteries according to the polarity markings. Replace the battery compartment cover.
·Within a short time the RF signal icon (located to the left of the outdoor temperature channel indicator) will start flashing. This indicates that the base station is ready to pick up the RF outdoor temperature signal from the remote sensor. It will continue to flash for 3 minutes or until the signal from the remote sensor is detected.

Register the Remote Sensor
·Open the battery compartment at the back of the remote sensor and slide the channel selector switch to your desired channel. For the first remote you may select any channel, for additional remotes select any unused channel
·Insert (2) AAA batteries according to the polarity markings. Be sure to install the batteries in the remote within the time that the RF signal icon is flashing on the base station. 1541 WeatherGuide Wireless Weather Forecaster with Barometer

[PDF]WS-8117 ATOMIC CLOCK WITH OUTDOOR WIRELESS ...

https://www.lacrossetechnology.com/products/.../misc/8117-manual.pdf

NOTE: Do not set the clock until the outdoor temperature is displayed. .... The unit will still try and receive the signal every day despite it being manually set. ..... sunlight, extreme cold and wet/moist conditions as these will lead to rapid changes ... Beforesending the atomic clock in for repairs, contact La Crosse Technology.

La Crosse Technology Top Solutions

https://www.lacrossetechnology.com/support/top_solutions.php

A: Complete a restart for display with the temperature/humidity sensor: ... to rest for 15 minutes can result in failure to connect with the outdoor sensor or missing ... Products set outside of these time zones will not search for a WWVB signal as it is ... locate the Clock or Weather Display near an outside wall and point the unit in ...

Common issues weather stations: Click Here

www.weather-station-products.co.uk/faqs/common-issues-weather-stations

Under £30 £30-£75 £75-£125 From £125 Birdhouses/Feeders Outdoor Clocks ... I'mnot getting any outdoor readings from my outdoor sensor, what do I do? This willcure 90% of all sensor connection problems, important you must ... is the airtemperature, to get this reading you need to place the unit away from direct sun.

Replacement Temperature Sensor ' AcuRite

www.acurite.com > All products

We would recommend a reset of your Weather Station. Please verify that you are using a good-quality, standard alkaline battery, and follow the steps below.

1. Remove the batteries from the outdoor sensor only.
2. In the outdoor section on the main unit, there will be a "CH" and number 1-3.
3. If on CH 1, press and hold the channel button on the back of the unit for 5 seconds.
4. Press and release the channel button one time, it should show CH 2.
   • If it does not change to CH 2, repeat steps 4 and 5.
5. Press and hold the channel button for 5 seconds.
6. Press and release the channel button one time, it should show CH 3.
   • If it does not change to CH 3, repeat steps 6 and 7.
7. Press and hold the channel button for 5 seconds.
8. Press and release the channel button one time, it should return to CH 1.
   • If it does not change to CH 1, repeat steps 8 and 9.
   ***Regardless of what channel you begin on, clear out each channel by holding the channel button and return to CH 1***
9. Reinstall batteries in the outdoor sensor.
10. Press and release the TX button.
11. Leave both units side by side for up to 30 minutes to gain a strong connection.

If you need any further assistance, please contact AcuRite Customer Support at 1-877-221-1252 or [email protected]

Hi Jerry,

While lithium batteries are recommended for the outdoor sensor it is not recommended they be used in the indoor display unit. Try using a good quality, fresh alkaline batteries and you should find your display turns back on.