Question about Kenwood Food Mixers

Open Question

Kenwood chef kvc50 only stays on for a second on all areas of speed control before you have to turn back to off to get another one second of action from it? Any ideas why please?

Posted by Julia Grantham on

Ad

5 Related Answers

Anonymous

  • 1 Answer

SOURCE: Kenwood chef 700w

I hope you didn't buy a new one, ours stopped last week after 25 years. All that was needed were new brushes for the motor. Anyone with a screwdriver could replace them. 4Kenwood had the parts to me in a couple of days.

Posted on May 31, 2008

Ad

Anonymous

  • 1 Answer

SOURCE: Blakeslee (Kenwood) A717 mixer speed control

I had the same problem. Had to strip the machine down to get to the motor. On the top is a moving plate with various capacitors etc mounted. On the front side there was a Capacitor (At least I think it was) with the wire broken.
I resoldered it and the machine now works fine.

I hope this helps

Posted on Jul 05, 2008

Ad
mirran

Mirko Blas

  • 515 Answers

SOURCE: Blakeslee A717 speed control

Hi,

where are you from, i have phone number to agents that still provide support for A700 series.

Posted on Jul 12, 2008

Anonymous

  • 26 Answers

SOURCE: Kenwood Chef A701 Variable speed controller

the solution its change the capacitor or triac, normaly problems in models A701 or A901 old motors

regards
kenwoodchefrestore.co.uk

Posted on Aug 19, 2008

Anonymous

  • 11 Answers

SOURCE: Kenwood chef 700w

IT NEEDS A REPAIR KIT.I CAN DO THIS. OR SEND A REPLACEMENT REPAIRED MOTOR FOR £25 PART EX FOR YOUR MOTOR.PLUS POST 07507400101. ****

Posted on Apr 04, 2009

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Kenwood chef keeps curdling eggs


Put water in Kenwood and a bowl inside the Kenwood to hold eggs. Eggs need to be done SLOWLY. Can also add a LITTLE water to aggs as they cook to slow down curdling . Basically you need to turn Kenwood into a double boiler. Lift bowl with eggs in and out of Kenwood to control temperature and whisk away now under control. Lift bowl and cool and slow down cooking and lower back in water and Kenwood to hear back up. Keep whisking and lift and lower bowl as needed. Some melted butter doesn't hurt either!

Jan 11, 2015 | Kenwood Food Mixers

1 Answer

How can I service an A901 kenwood mixer, need to get top plate off.


the speed control on my kenwood chef A901 is not working
how do i fix this.

Oct 16, 2012 | Kenwood Chef Major A701 A901 Cm170 Km201...

2 Answers

Kenwood Chef KM400 motor speed is too slow


A failed SCR or triac will not always show visually any sign of failure. Chances are good that is all that is wrong. If mixer had been plugged in when it got wet, that is all it takes. Also check the transient voltage supressors if the chef has them. They would be identified on the circuit board. as TVS or MOV along with a number. Only number to use is the one on the component.

If you can find ratings for the old devices, just matching the basic ratings should do. Just guessing, but the SCRs should be 20 amp and 400 volt, If the old ones are a lower rating than my guess, there is no problem with using the higher ratings, if my guess is low, go with the original's ratings. Manufacturer of device does not matter as long as ratings are at least comparable.

Jan 19, 2012 | Kenwood KM400 / KM410 Chef Classic Stand...

1 Answer

Kenwood chef A901 food mixer speed dial only engages when pushed in


Thank you for your help. Have fixed the problem by tapping speed control shaft back into the motor housing to remove the endplay.Fault can be found by checking for in and out movement of the dial itself. there is only a small amount when correct. T W Faint

Jan 16, 2010 | Kenwood Food Mixers

1 Answer

Kenwood Chef - slowest speed


if you have max speed you have to replace the .1uf capacitor the 2 spring loaded screws serve far fine adjustment

Feb 02, 2009 | Kenwood KM400 / KM410 Chef Classic Stand...

1 Answer

Speed control not working


What model is your Kenwood ? to Kamalsalman

A901 models change triac and capacitor .. or centrifugal broken

also check if another's components is faulty.

Kenwood Chef Restore

Dec 22, 2008 | Kenwood KM800 Major Classic Stand Mixer

2 Answers

Difference Kenwood Chef A701 and Kenwood A901


Hello.

the difference between A701A and A901 is :

high speed outlet
slow speed outlet

planetary hub is similar . A701A, A901 and KM series

A701 Different planetary hub and fit different tools.

is not same A720 and A920 A7 = A701/A
A9 = A901 and KM

In our web site Kenwood Chef Restore in Downloads section.
you can download the compatibility of the models A700, A701 , A900 and KM series .

Regards

Oct 02, 2008 | Kenwood KM400 / KM410 Chef Classic Stand...

3 Answers

Kenwood Chef A701 Variable speed controller malfunction. Appliance only operates on maximum speed.


the solution its change the capacitor or triac, normaly problems in models A701 or A901 old motors

regards
kenwoodchefrestore.co.uk

Aug 07, 2008 | Kenwood KM300 Chef Stand Mixer

Not finding what you are looking for?
Food Mixers Logo

Related Topics:

175 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenwood Food Mixers Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Lawrence Oravetz

Level 3 Expert

10548 Answers

Ross Keen

Level 3 Expert

1364 Answers

Are you a Kenwood Food Mixer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...