Question about Konica Minolta Office Equipment & Supplies
Solution B: find a pico fuse of the same value and put it place. (if you are a tech you know the value, it the same in fuser or TBU ). Aldo
Posted on Apr 20, 2019
C0500 refers to a low fuser temperature. You can attempt to clear the code by using the tech rep service mode.
Go to "Counter"
Go to "Trouble"
If "warm Restart Swich" is asked for- This can be actuated through a small access hole on the right side of the control panel, using a straightened paper clip or something similar.
You may need to clear the counter by pressing "clear" and then "end".
After clearing the code, power cycle the copier. If it comes to "ready" you are all set. If not, you may have a blown heat lamp or thermal fuse which would need to be replaced by a technician. Good Luck!!"
Posted on Oct 31, 2007
SOURCE: how do i replace the
When you open the door to access the toner and waste toner area, you will see a letter "K" on the left side of the waste toner box, and a thumb screw on the right side of the waste toner box. Immediately above the letter "K" there is a raised area in the brown plastic housing. It is between the blue toner cartridge, and the waste oner box. There is a second raised area 2.5 inches at a 225 degree angle below the thumb screw on the right side of the waste toner box.
If you will place your thumbs on the raised areas and your forefingers on the white plastic rear cover of the waste toner box immediately below the raised areas and squeeze your fingers towards your thumbs, the waste toner box will come forward at the top of the box. You can then lift the waste toner box up and out of the printer.
Please squeeze carefully if you think your waste toner box is close to full as you may inadvertently find waste toner all over the place.
The two blue caps on the back of the waste toner box are to keep the waste toner in the waste toner box instead of your carpet.
Installation of the new waste toner box is the reverse of the above procedure. The new waste toner box almost snaps in place.
Here in California waste toner is considered a hazardous material and must be disposed of properly.
Posted on May 14, 2009
First check the alignment front and rear of the finisher, check the finisher exit guide rollers if the paper is exiting properly, open both rear and the front cover and check the lower gears attach is the up/down drive belt. that lower gear one might be broken by the pin slot.
Posted on Jul 09, 2009
You can change the 2300's menu setting to ignore empty toner cartridges and keep printing. There are 2 steps:
Press Menu/Select, then "right arrow" until you see ENGINE. Press Menu/Select again and then "right arrow" until you see TONER EMPTY. Press Menu/Select and you'll see STOP. Press "right arrow" once to change to CONTINUE. Press Menu/Select.
Press "right arrow" until you see AUTO CONTINUE. If set to ON, press the "Cancel" button and you're ready to print. If set to OFF, press Menu/Select, then right arrow to change to ON, then Menu/Select to enter. It will say "ON IS SELECTED." Then press the "Cancel" button and you're ready to print.
Posted on Apr 07, 2010
Tips for a great answer:
Apr 17, 2018 | Konica Minolta Office Equipment & Supplies
Jul 13, 2016 | Konica Minolta Office Equipment & Supplies
May 13, 2016 | Konica Minolta Office Equipment & Supplies
May 04, 2016 | Konica Minolta Office Equipment & Supplies
Dec 18, 2015 | Konica Minolta Office Equipment & Supplies
May 23, 2015 | Konica Minolta Bizhub C451...
Jan 04, 2014 | Konica Minolta Magicolor 3730dn 4750...
Feb 14, 2013 | Konica Minolta MINOLTA BRAND DIALTA...
Nov 28, 2007 | Minolta magicolor 2300W Laser Printer
38 people viewed this question
Usually answered in minutes!
Level 3 Expert
Level 1 Expert
Level 2 Expert