Question about Samsung Televison & Video

1 Answer

Samsung dish washer flashing lights... normal, heavy, and smart lights are flashing

Only stays on for about 3 minutes in short wash and then shuts off and the 3 lights flash

Posted by Holly DeYoung on

Ad

1 Answer

karen sharon

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Night Owl:

    An expert who has answered 10 or more questions between 12 midnight and 6am on the same day.

  • Contributor
  • 28 Answers

Clean filter

Posted on Mar 21, 2019

Ad

5 Related Answers

Amigaman

Gerald Griffin

  • 248 Answers

SOURCE: 665.17019401 - Kenmore diswasher

It indicates a water temp problem. If water temp doesn't rise at a certain rate, by the heater, it goes into this error. Probably a problem with heater or wires to it.

Posted on Nov 22, 2007

Ad

Anonymous

SOURCE: Maytag dishwasher error code "1H" MWB6601AWB

The 1 H is not a fault code it is the delay time of one hour.

Posted on Jul 30, 2008

Jrussell789

  • 172 Answers

SOURCE: KENMORE ELITE DISHWASHER - MULTI-LIGHTS FLASHING

Look at your manual, usually available on net for reading or downloading. Blink lights are often used to code out a problem with various combinations and repetition rates to indicate trouble code number for look-up in manual.

Posted on Feb 22, 2009

Anonymous

  • 2 Answers

SOURCE: ''clean'' light flashing (whirlpool Dishwasher GU2300XTLS1 model)

I had the same problem recently and a repair person came to my home to fix the dishwasher. He said he had to reset the control panel. He did this simply by making sure the soap dispenser door inside the washer was closed, then making sure the main dishwasher door was closed and locked. Then he quickly pushed the Heated Dry button and the Hight Temp wash button alternately. He said each button needed to be pushed twice within five seconds. After he did this all the lights on the control panel came on, then turned themselves off before the washer went in to a test cycle. This simple reset fixed the whole problem. Works great so far.

Posted on Jun 16, 2009

Anonymous

  • 1 Answer

SOURCE: The wash light Indesit DI 67 dish washer is flashhing ?

Try pressing the start button in for 5 seconds, doing this cancells the old program and starts a new one.

Posted on Mar 11, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

GE WASHER LIGHTS FLASHING BUT NOT WORKING


It won't change because the cycle was incomplete and the safety control is preventing a restart. Until you get professional onsite service; unplug the washer; make certain all of the water is drained out, and disconnect the hoses. Have someone help you tilt the washer forward and lay on the front side. Pick it up again and reach into the tub area and spin the tube around, and kind-of move it side to side. Hook it back up, plug it into the power supply and reset the timer to start a short wash. Try to start and see if you get any action. If after all of that; nothing changed, the timer on the circuit board is stuck where you left off when the unbalanced load shut it down.

Dec 23, 2013 | GE Profile WPRE6100G Top Load Washer

1 Answer

Shut off on volume 25, and protection light comes on and starts flashing. i unplug it and demo stays on forever till i hit the power button and comes on for 2-3 sec. then shuts back off with red light...


Try reseating all wires in the speakers, you could have it shorting out. If that doesnt work try change the cables. If that doesnt work then try plug one speaker in at a time on different channels to test if it is a short within the speaker or the speaker output.

-Dubkingz

Jun 12, 2011 | Sony MUTEKI HTDDW1600 Theater System

1 Answer

Hobart LXIH stuck in Wash mode after running multiple loads. Shutting off breaker for several hours fixes problem until multiple loads have been run again and then it is once more stuck in Wash mode.


How long does it stay in the wash cycle? Indefinitely? Does the display continuously show "WASH"?. If it stays in the wash cycle indefinitely (i.e. continuously shows "WASH" for significantly beyond approx. 3 minutes), it's probably a control board malfunction. If it continues to wash after the "WASH" indicator goes out, it could be a shorted wash motor relay on the relay board or a fauly control board.

If the internal rinse water booster heater doesn't reach it's programmed setpoint temperature in time, the dishwasher will run an extended wash cycle to give the booster heater more time to finish heating the rinse water. If this is what's happening, the wash cycle would last approximately 3 minutes, then it would rinse regardless of whether the booster heater has finished heating or not.

The booster temperature thermistor may be bad, giving a false booster temperature reading, causing an extended wash cycle as described above. The booster heater elements or contactor may be bad, preventing the booster heater from heating and reaching proper temperature, also causing the same extended wash cycle to give the booster more time to heat.

Jan 06, 2011 | Hobart 24 in. LXIH-3 Built-in Dishwasher

1 Answer

Status indicator flashes 3 short times, then one long red flash


Once the status light blinks 3 times, this is an indication that there's a problem with the lamp. The lamp may need a replacement.

If you replace the lamp, but get the same problem, check the inverter board.

If you're not sure where the inverter board is, then you may need to contact a pro for your safety.

Good luck and have a good evening!

Feb 14, 2010 | Mitsubishi WD-52327 52" Rear Projection...

1 Answer

55" TV keeps shutting off automatically


Green light flashes 5 and then red light flashes 6

Sep 14, 2009 | Sony KDF-E55A20 55 in. LCD Television

1 Answer

Red and green light flashing and wont work


PROBABLY A SHORT IN THE BANKET ITSELF AND IT SHUTS OFF TO PREVENT SHOCK OR FIRE.

Apr 27, 2009 | Washing Machines

2 Answers

Kenmore Elite Dishwasher clean light ind flashing and won't start


You will have to reset the console. To do this, close the door and press these buttons in sequence...

-high temp wash
-heated dry
-high temp wash
-heated dry

...all the lights will turn on briefly and the machine will start a diagnostic cycle. You can press cancel or let the diagnostic cyle finish (1-2 minutes).
You should now be able to run the dishwasher as normal.

Feb 17, 2009 | Kenmore 24 in. 15142 Built-in Dishwasher

1 Answer

Kenmore elite model 16574


press (high temp-wash) button and then ( heated dry)
do that 3 times in that order within 5 seconds. So it looks like this:

(high temp-wash) ( heated dry) (high temp-wash) ( heated dry) (high temp-wash) ( heated dry)

That will start a short diagnostic cycle (last about 2 minutes) that will clear the blinking light and allow you to use the dishwasher. If the light comes back, your drying cycle has failed and you will need service.

Oct 28, 2008 | Kenmore 24 in. 16352 / 16354 / 16359...

2 Answers

TP50G60 bad scrambled picture - shuts off after 1 minute


This does not sound to me like a convergence roblem. It could be a shorted picture tube. That would put the set in a shutdown condition. Normally in Toshibas , the picture remains on with a convergence problem. Here is something you can try, but you must be very careful. Remove one crt board at a time from all three tubes. if the set stays on after one of the crt board are removed , then that is the shorted picture tube.I cannot caution you on how care full you have to be trying this procedure. Scrivitron

Jun 29, 2007 | Toshiba TP50G60 50" Rear Projection...

Not finding what you are looking for?
Televison & Video Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Samsung Televison & Video Experts

The Knight
The Knight

Level 3 Expert

76332 Answers

Muntejaya Ginting
Muntejaya Ginting

Level 3 Expert

10422 Answers

Ekse

Level 3 Expert

13434 Answers

Are you a Samsung Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...