Question about Canon Office Equipment & Supplies

2 Answers

My Canon ir 3045 gives blurry print out. How to get rid of the same?

Posted by M.S.Shah on

Ad

2 Answers

Jai Narayan Sharma

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Blur copy means u need to clean CCD & add oil to the scanner moving rod i am sure problem will be remove

Posted on Aug 05, 2020

Ad

Lenin Hudiel

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Canon Master
  • 913 Answers

Try this . Make some copies ( at least 5) and open one of the covers while machine is making copies. Remove the paper jam and verify if the copy is blurred. Do this to be sure of what unit is causing the blurred copies. If copy information is good before the paper enter in the fixing unit . That mean the problem is is the fixing unit

Posted on Jan 14, 2019

Ad

5 Related Answers

redzventures

Jay Otaigbe

  • 149 Answers

SOURCE: I have an IR-3300 Model xerox machine. It was

The two problems may not be related. Adding toner should not under most circumstances cause copies to become light, unless the toner you are using is of a poor quality - I hope it is a Canon cartridge or quality generic. It sounds as though your fixing film or drum unit may need replacing, or perhaps you need to perform a install procedure. As the 'install - toner - start' option is free, try it first:

First press the head key and then the number '2' and '8' keys at the same time then press the head key again. This will take you into service mode - select 'copier' then 'install' then 'toner' then 'start'. This will run throught a cycle that takes a little while, I think about 599 seconds (sorry for been so accurate but unhelpful but that's what I remember from the display - never converted into minutes but you're welcome to).

But if you are having blurry or even dirty or light copies it may be the fixing film. When the copies are printed, immediately check if you can rub off the toner at all by rubbing the print with your fingers - if so this indicates that the fixing unit is not hot enough or there is not enough pressure - check that the fuser is in properly and that the jam release lever is not engaged.

Lastly, it could be your drum unit that is faulty or worn. Totest this you will need to try and stop the machine in the middle of printing before it reaches the fuser - open the front cover and latch down the transport bed with the green handle - remove the paper gently so as not to disturb the ink in any way and observe the image quality - if it is displaying the exact same symptoms then it is not your fuser and is probably the drum unit or dodgy toner - most likely the drum. However, if the image is fine, then it most definetely is your fuser film (and or perhaps the cleaning roller that cleans the film).

Good luck

Posted on Jul 31, 2009

Anonymous

  • 39 Answers

SOURCE: canon ir-400 error load paper when i give data

More than likely your computer's setup for where it is to pull the paper from has designated the manual bypass tray (the flap on the side of the right side of the copier that holds paper) as it's main source. Go into the control panel/printersandfaxes/ and look under the profile tab of your copier. Good luck

Posted on Dec 18, 2009

Anonymous

  • 20 Answers

SOURCE: How to copy a booklet on the canon 3045...

To make a stapled or folded booklet on the 3045 will require the "Saddle Finisher option. This is a finisher the attaches to the left side of the copier. It has 2 trays and an additional tray on the very bottom of the finisher. If you do not have this it will be impossible to make a booklet that is two sided with the pages properly sequenced. If you have the saddle finisher attached. On the screen select special features and on the first or second screen you will see a booklet button, press that and follow the prompts. If the booklet button is greyed out you do not have the Saddle Finisher.

Posted on May 20, 2010

nareshtex

  • 1 Answer

SOURCE: USA - COPIERS - IMAGERUNNER 2230 Copier: canon IR 2230 r giving me an error E000024-0001...

eroor 000024-0001 error is found in cannon ir 2870 machine, how is solve the problem

Posted on Aug 25, 2011

razafaiz

  • 1 Answer

SOURCE: canon ir 3045 error code E00002 0000

CANON IR 3045 ERROR CODE E000002-000, plz urgent rply solution

Posted on Mar 22, 2012

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Canon ir 3045 copier over heating problem give me solution


Are you experiencing any issue with Canon printer setup or Canon printer drivers and looking for canon printer technical support? Call us 1-800-243-0019 @ Toll Free Number

Apr 14, 2017 | Canon Office Equipment & Supplies

1 Answer

MY canon iR3035 ccd scanner position is faulty..


Re: canon ir 3035 copy not lined up 1/4 inch higher it scans but configuration page i
service mode > copier > adjust > adjust xy > adjust Y input the value from the label on the front cover
This is all I could find. Try adjusting by 1/4 inch. Thank you Santosh

Jun 25, 2016 | Canon imageRUNNER 3035 Black and White...

1 Answer

Can i hack ir 3045 to enable printer board


Not that I know of, you have to buy the licence firmware to upgrade to print

Mar 04, 2014 | Canon Office Equipment & Supplies

1 Answer

Canon ir 3045 error code e000007-0000


E007
The rotation of the fixing film is faulty.
0000
While the fixing motor is rotating, the marker
signal is not detected for 6 sec with the reading of
the main thermistor indicating 100 deg C or more.
Reset the condition in service mode:
COPIER>FUNCTION>CLEAR>ERR. Replace the
main thermistor. Replace the DC controller PCB.

Jan 09, 2014 | Canon (6981A002AA) for imagerunner 2200,...

1 Answer

Blurry copies


clean ur leser mirror&full gradiation adjust

Feb 08, 2013 | Canon imageRUNNER iR C4080 Color Copier

1 Answer

CANON ir 3530 finisher error


canon ir 3530 shows finisher error (displays spanner)

Nov 10, 2012 | Canon gpr-16 ir 3530 blk...

1 Answer

Canon ir 3045 error code E00002 0000


CANON IR 3045 ERROR CODE E000002-000, plz urgent rply solution

Dec 01, 2011 | Canon iR 2016i Black and White Copier

2 Answers

Ir4570 message: finisher cannot be used help me pls.


Dear colleagues,

I have Canon IR 3045, is giving the following message "finisher cannot be used" is there any solution to reset the message.

Many thanks for any assistance.

Boualem
uae

Sep 16, 2010 | Canon ImageRUNNER 3570 Copier/Printer

2 Answers

Canon irc5185 new machine, print not good


run auto gradation adust in add. func. on heavy paper then check each colour ! at a time it iis possible ! of the new drums has failed. good luck

Nov 20, 2009 | Canon Office Equipment & Supplies

Not finding what you are looking for?
Office Equipment & Supplies Logo

Related Topics:

117 people viewed this question

Ask a Question

Usually answered in minutes!

Top Canon Office Equipment & Supplies Experts

old marine
old marine

Level 3 Expert

2312 Answers

Muntejaya Ginting
Muntejaya Ginting

Level 3 Expert

10422 Answers

Tareq Bin Mostaq...
Tareq Bin Mostaq...

Level 3 Expert

1449 Answers

Are you a Canon Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...