Question about Maytag Refrigerators

2 Answers

How to take apart frame from glass shelf on Maytag MFB2055FRZ that hold the baskets under shelf

Was able to take end and central brackets out but unable to seperate the 2 parts plastic that hold the glass in place

Posted by Fidele St-Amand on

Ad

2 Answers

Jeremy Wheeler

  • Level 1:

    An expert who has achieved level 1.

    Welcome Back:

    Visited the website for 2 consecutive days.

  • Contributor
  • 1 Answer

I seem to be having the same issue with a Maytag refrigerator model M1TXEGMYS01. I would like to thoroughly clean all shelves of this new-to-is refrigerator but I can’t seem to figure out how to remove the glass from the plastic housing. I was able to take the end and central brackets off (that hold the drawers) but I can’t figure the rest of it out... and the manual I looked up didn’t provide any information on separating the housing either. Please see pic attached. Thanks in advance!
How to take apart frame from glass shelf on Maytag - 4_18_2020_8_33_32_am.jpeg4_18_2020_8_33_37_am.jpg

Posted on Apr 18, 2020

Ad

cluffermon

  • Level 1:

    An expert who has achieved level 1.

    Governor:

    An expert whose answer got voted for 20 times.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 4 Answers

First try removing as described by your manual (See below).

The glass may be stuck in the track. Small amounts of liquid may "glue" the glass to track.warm up the compartment by shutting power off and leaving door open. Use a round ended thin spreading knife. Wet it with warm water and try to slide it between the glass and the track. Work it along the crack until they separate with a gentle wiggle.

From the owners manual
Important information to know about glass shelves and covers: Do not clean glass shelves or covers with warm water when they are cold. Shelves and covers may break if exposed to sudden temperature changes or impact, such as bumping. Tempered glass is designed to shatter into many small, pebble-size pieces. This is normal. Glass shelves and covers are heavy. Use both hands when removing them to avoid dropping.

Refrigerator Shelves The shelves in your refrigerator are adjustable to match your individual storage needs. Glass Shelves To remove a shelf: 1. Remove items from the shelf. 2. Slide the shelf straight out to the stop. 3. Depending on your model, lift the back or front of the shelf past the stop. Pull the shelf out the rest of the way. To replace a shelf: 1. Slide the back of the shelf into the track in the wall of the cabinet. 2. Guide the front of the shelf into the shelf track. Be sure to slide the shelf in all the way.

Posted on Jan 06, 2019

Ad

5 Related Answers

Anonymous

  • 47 Answers

SOURCE: rear glass hatch latch bracket came off glass

not sure of the set up on your jeep off the top of my head, but uruthane glass adhesive is the only thing that is good on glass......its what holds in all the glass on your vehical

Posted on Jun 29, 2009

Anonymous

  • 119 Answers

SOURCE: driver side car seat side panel will not stay latched

you need new clips ,avable through subaru,i believe they are better than ones equipped originally

Posted on Jul 16, 2009

cardenderek

Derek Carden

  • 783 Answers

SOURCE: White plastic bracket holding headlight

headlight bracket, headlight adjuster, or headlight adjuster bracket

Posted on Mar 30, 2010

Anonymous

SOURCE: Can the frame under the

How can a 13 year old sub-frame, have rusted out?
You could remove it,media blast it,and cut out rusted sections and weld in new.
You could get a used one from a salvage yard.

Posted on Sep 29, 2010

jturcotte

Jeffrey Turcotte

  • 8984 Answers

SOURCE: 2 of the bolt on

I don't quite understand what sheared off, but all brackets come off the engine. If your bracket is bad, I recommend you get a used one at a wrecking yard. They will have lots of them.
If a bolt is sheared off, did it leave a part behind in the pump? If yes, it will have to be drilled out. Please let me know if you have more questions, and thanks for using FixYa.

jturcotte_613.gif

Posted on Dec 25, 2010

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why does the washer basket tilt to the side


Had a similar problem, this might be the solution.

Unplug the washer, remove the two screws that hold the control panel to the top. Tilt the panel back, remove the plug going to the top and the two clips that secure the back to the case. Tip the case forward to release it from the front edge of the bottom frame and set it aside. From the front, you should see two springs attaching the bottom of the tub to the lower frame. The tub end of the spring is attached to a bracket that is screwed into the tub. In my case, the screw holding the bracket to the tub had vibrated loose, causing the centering effect to be lost. There is a third spring in the back if those two are intact.

Replace the bracket and screw, and you should be back in business. Best of all, it only takes time.

Feb 13, 2011 | Whirlpool 3.2 cu. ft. Plus Washer

1 Answer

Maytag refrigerators mtbe1956de liquids have dripped on to the bottom glass shelf and seeped under the edges where it cannot be cleaned. do I have to remove the vegetable drawers and totally dismantle the...


brute force on the glass shelf.... it was just stuck in place by the cold sticky liquid that had seeped under the edges and bonded the glass and plastic together

Jan 12, 2010 | Refrigerators

3 Answers

Can i take apart the door shelves of my subzero for cleaning


You can take them off the door by lifting up and out at an angle but do not try to disassemble them. You can soak them in hot water to try and get rid of spills in the seams.

Jul 12, 2009 | Sub-Zero 650 / O Bottom Freezer...

1 Answer

How to remove take glass shelf to clean trapped spills


lift the front nosing by prying with your fingernails up...it will roll in place allowing you to remove the glass

Dec 20, 2008 | Maytag MTB1895AE Top Freezer Refrigerator

1 Answer

Bracket holding glass over fruit / veg compartment broke


http://www.partselect.com/Schematics/Maytag/54436.gif Maybe this diagram will help you. www.partselect.com I just replaced the Crisper Shelf Frame. I received it very quickly. I am now looking for some sort of support for the whole shelf, because it still seems to be sagging. I may have to invent something. If anyone out there has a solution, please post it.

Aug 26, 2008 | Amana ARB2217CSR Bottom Freezer...

1 Answer

Maytag Elevator Shelf


Let me just say, your post helped me, because I realized that I was not going crazy.  But, I was able to find the manual on this frigerator, which was key.  There was one phrase in the manual that gave me help - "when the glass shelf is pushed to the rear, it will align the rear latches.
Manual from whirlpool website: http://shared.whirlpoolcorp.com/assets/pdfs/literature/MSB2154ARA.pdf

So, the rear latches must be installed in such a way that the sliding glass shelf not only touches them, but pushes them into the correct position.
This fact helped me to try different positions, each time testing to see if the glass shelf would do anything.  Finally, I realized that there is a triangular shaped part of the rear latch.  The hypotenuse of the triangle is what comes into contact with the little nub on the underside of the glass shelf.  The nub on the glass shelf pushes the rear latch along the hypotenuse of the right triangle, and into the correct position.
Here is a picture of it installed in my frigerator,which I am sure will tell it better than any words:
a564cb9.jpg

Oct 08, 2007 | Maytag MSD2756G Side by Side Refrigerator

10 Answers

Maytag electric range door handle (how to replace?)


The above solution is fine, but you don't have to remove the door.  Open the storage drawer for access to the trim screws (3) on the bottom of the door, remove the screws.  Have a helper hold the glass along the bottom. Take the three screws on the top of the door trim out.  Slide out the glass and put in a safe place.  Remove the four screws that hold the handle brackets in place, remove the handle (or tighten if loose). Install the new handle (one screw on each side).  Reinstall all parts in the reverse order of disassembly.  The entire job took less than 30 minutes.

May 01, 2007 | Maytag MER5775Q Electric Kitchen Range

Not finding what you are looking for?
Refrigerators Logo

Related Topics:

192 people viewed this question

Ask a Question

Usually answered in minutes!

Top Maytag Refrigerators Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Michael Thomas
Michael Thomas

Level 3 Expert

3053 Answers

John Tripp
John Tripp

Level 3 Expert

4656 Answers

Are you a Maytag Refrigerator Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...