Question about Whirlpool Dishwashers

1 Answer

Whirlpool dishwasher normal and pots/pan lights flashing

Posted by chris steinmann on

Ad

1 Answer

Kenebob

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Habit-Forming:

    Visited the website for 3 consecutive days.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 12 Answers

My whirlpool dishwasher gold GU2475XTVQ0 had rapid blinking lights that started with the "4 Hour Delay" LED and changed to others when other buttons were pressed. The machine would not run. I followed the instructions located behind the kick panel and verified the keypad was the issue and not the control circuit by elimination.
The big surprise for me was that when I used a straight pin to resistance check all of the buttons, they checked out OK. I reconnected the 14 pin connector (P1) to the control and found that the buttons/LEDs were behaving correctly! I believe that pushing the straight pin into the 14 pin connector removed any corrosion in the 10 year old device and permitted the keypad to communicate with the control again.
I reassembled the dishwasher door and it ran with no problems. I was ready to replace the keypad for $150, but didn't have to!

Posted on Jun 14, 2019

Ad

5 Related Answers

catriver

Ron Marek

  • 878 Answers

SOURCE: Dishwasher's "Pot-n-Pans" light flashing

ga, behind the toe panel on the bottom there should be a tech sheet explaining how to put the dishwasher in the test mode. See if you can enter the test mode. If you can't, you probably have a stuck or shorted keypad. Catriver...post back

Posted on Mar 03, 2007

Ad

Anonymous

  • 148 Answers

SOURCE: Flashing pot and pan light

shut off the power and see if the unit will reset. if its plugged in, it will be easy, look under the sink. if not, try a breaker.
let the power stay off for about a minute.
then back on.
if not restored, then you have logic boards that failed.
sorry,
good luck
mark

Posted on Dec 28, 2007

yalmer

Hjalmer Lamminen

  • 552 Answers

SOURCE: Kenmore Dishwasher #15769

Try this solution first
Push the Hi-temp and then push the Sani-rinse. Go back and forth multiple times on these two buttons. I found that after a handfull of pushes that a "1" came up on the display. I continued to keep rotating the two buttons and then a "2" came up on the display and the dishwater started it's "drain" phase. I then hit cancel to clear and then I selected the cycle I wanted. The washer started up just as normal at this point.

Posted on Feb 16, 2008

IFIXALL

Archie Ferrarini

  • 869 Answers

SOURCE: Whirlpool Quiet Partner 980

Bad control board ,replace it.

Posted on May 26, 2008

Jeff Meyer

  • 423 Answers

SOURCE: The only number on the nameplate of my

Yes, you almost certainly have a Whirlpool Gold Quiet Partner III Model #8575637
Of course the great news with buying from Costco is the ability to return products you are dissatisfied with. Check with the customer service desk.
Please reply if you want to to get into repairing it and we will get under way.

Posted on Mar 31, 2009

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My whirlpool quiet partner II imperial series Dishwasher will only work on light wash mode. Normal wash, heavy wash or pots and pans cycle will not work at all.


This is ordinarily a problem with the touchpad. Can you give me the specific model number of yours (ordinarily on a sticker on the inside edge of the door or on the door opening)?

Mar 06, 2016 | Whirlpool Dishwashers

1 Answer

My Whirlpool Dishwasher DU1300XTV


Heating element goes bad causing the controller to go bad as well

May 14, 2014 | Whirlpool DU1300XTVQ Dishwashers : Built...

1 Answer

The panel is stuck on pots/pans for cleaning and wont let me run the dishwasher. the pots/pans light keeps flashing


Hello,

To reset the dishwasher push in this order the,

HIGH TEMP WASH- HEATED DRY- HIGH TEMP WASH- HEATED DRY - CANCEL/OFF

the control will be reset...but more importantly how many times in a row does the light flash..it will indicate what error code its displaying??

example if it flashes 4 times then a pause then flashes 4 times again its displaying the error code#4
7 flashes then pause then 7 flashes its displaying the error code#7 ect ect



GENE

Sep 06, 2011 | Whirlpool 24 in. DU1055XTPS Stainless...

1 Answer

Pots and pans and normal lights blinking


That reset sequence code didn't work for me. We tried everything on a ton of forums.
What I did to fix our Whirlpool dishwasher was to disconnect the drainage tube from the garbage disposal. I noticed it smelled really bad so I figured it was clogged. I used a bucket to catch the water left in the tube. I took the sprayer from the sink and flushed out the tube. 4 pumpkin seeds and a couple of beans landed in my bucket. I flushed it a couple times. I hooked the tube back up to the disposal and sure enough all the lights returned to normal. I pressed start and it came on.

Feb 22, 2010 | Whirlpool GU2200XTSB GU2200XTSQ 24 in...

1 Answer

Whirlpool Quiet Partner 980


Bad control board ,replace it.

May 26, 2008 | Dishwashers

2 Answers

Flashing pot and pan light


shut off the power and see if the unit will reset. if its plugged in, it will be easy, look under the sink. if not, try a breaker.
let the power stay off for about a minute.
then back on.
if not restored, then you have logic boards that failed.
sorry,
good luck
mark

Oct 24, 2007 | Whirlpool GU2400XTP Built-in Dishwasher

Not finding what you are looking for?
Dishwashers Logo

Related Topics:

1,657 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Dishwashers Experts

Michael Thomas
Michael Thomas

Level 3 Expert

3056 Answers

Mike

Level 3 Expert

4372 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Are you a Whirlpool Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...