The chimes an turn signal noise come out driver door speaker . Both front speakers not working could be a blown circuit fuse inside the radio or just blown front speaker channel . Your best bet , take it to a GM dealer or someother qualified repair shop . You have no idea of the complexity of this . The radio can set DTC'S - diagnostic trouble codes , believe it or not !
DTC B1025, B1035, B1045, or B1055
DTC B1025 01: Audio Output 1 Left Front Circuit Short to Battery
DTC B1025 02: Audio Output 1 Left Front Circuit Short to Ground
DTC B1035 01: Audio Output 2 Right Front Circuit Short to Battery
DTC B1035 02: Audio Output 2 Right Front Circuit Short to Ground
DTC B1045 01: Audio Output 3 Left Rear Circuit Short to Battery
DTC B1045 02: Audio Output 3 Left Rear Circuit Short to Ground
DTC B1055 01: Audio Output 4 Right Rear Circuit Short to Battery
DTC B1055 02: Audio Output 4 Right Rear Circuit Short to Ground

Each of the audio output channel circuits (+) and (-), at the radio and audio amplifier have a DC bias voltage that is one half of the battery voltage. When using a DMM, each of the audio output channel circuits will measure approximately 6.5V DC. The audio being played on the system is produced by a varying AC voltage that is centered around the DC bias voltage on the same circuit. The AC voltage is what causes the speaker cone to move and produce sound. This voltage will vary depending on what type of audio is being listened to, talk or music, and type of music, as well as the volume setting of the system. Low volume and talk settings will measure around 1V AC and less, where constant music may measure 3V AC and slightly higher.
DTC B1287 01: Amplifier Control Signal Circuit Short to Battery
DTC B1287 02: Amplifier Control Signal Circuit Short to Ground
DTC B1287 04: Amplifier Control Signal Circuit Open

The radio provides a remote amplifier mute output circuit to control overall muting of the remote amplifier. The amplifier receives pulse width modulated (PWM) signals on the control circuit at varying duty cycle percentages for controlling muted and unmuted functions of the amplifier. Circuitry internal to the radio monitors the remote amplifier mute circuit for faults and sets the appropriate DTC when faults are detected.

Feb 16, 2018 | 2010 Chevrolet Cobalt

1 Answer

Integra 5.3 keeps turning off so TV will not go on. It flips back to standby mode after 2 seconds and screen says check signal cable or check connections. This issue started yesterday with a loud noise...

you most likely have a blown main output transistor or a shorted speaker. first get a mutimeter and set to lowest ohms setting and check for 4-8 ohms ( CHECK IMPEDENCE rating on back of speaker) at the speaker terminal of the speaker. if this checks out then you take the meter and set to DC and place the + / - terminals to the speaker connection on back of receiver then turn on the receiver . notice if you have any dc voltage at any sp terminal, if dc is present you have a blown output transistor. If you are not an electronic tech please refer your unit to a qualified service tech. I hope this helps.

Jan 16, 2014 | Integra DTM-5.3 Receiver

1 Answer

Integra DTR-5.6, no sound for am/fm tuner

reset receiver if that does not work You will have a defective processor pcb

Aug 24, 2013 | Integra DTR 5.6 Multi Media Amp

1 Answer

Dtc = B1025 Driver/pass Deploy Loop Short To Voltage What does this mean?

If your asking about the radio DTC this is what it is

Circuit Description

When the radio is powered up, the radio supplies low level audio signals to the speakers. If the vehicle is equipped with an audio amplifier, the amplifier will boost the signal sent to the speakers.
Conditions for Running the DTC

The test is performed when the radio switches from OFF to ON. The radio will continue to test for the fault once every 0.5 seconds.
Conditions for Setting the DTC

The radio sets a current status for this DTC when a short to ground or voltage is detected on any of the speaker channels for 1.5 seconds.
Action Taken When the DTC Sets

No sound is present from one or more of the speakers.
Conditions for Clearing the DTC

The fault condition is not present for 5 seconds.

What to do:Test the speaker outputs from the radio for short to ground or voltage. Inspect for poor connections at the harness connector of the radio. Reprogram the radio. Replace the radio.

Sep 10, 2011 | 2003 Chevrolet Silverado 1500

1 Answer

I JUST WANT THE CODES FOR CHEVY TRAILBLAZER 2004...

Feb 7/11 - P0405

Jan 11/11 - P0336 - P0326

Dec 28/10 - P0217 - P0218 - P0163 - P0230 - P0231 - P0232

Dec 9/10 - Trouble Codes: P0170 - P0173 - P0162 - P0154 - P0142

Dec 6/10 - More DTC articles: P0157 - P0158 - P0160 - P0200

Nov 30/10 - DTC articles posted: P0505 - P0156

Nov 18/10 - More new articles: P0143 - P0144 - P0146 - P0147 - P0152

Nov 12/10 - P0120 - Throttle Position Sensor/Switch A Circuit Malfunction

Nov 11/10 - ECT Circuit Codes: P0116 - P0117

Nov 10/10 - P0111 - IAT Circuit Range/Performance Problem

Nov 7/10 - P0110 - Intake Air Temperature Circuit Malfunction

Nov 6/10 - P0108 - Manifold Absolute Pressure/Barometric Pressure Circuit High Input

Oct 21/10 - P0216 Injection Timing Control Circuit Malfunction

Sept 11/10 - Knock Sensor DTCs: P0327 P0332

Mar 15/10 - P0607 Control Module Performance Code

Mar 4/10 - P0606 PCM Processor Fault DTC

Feb 10/10 - New ECT Sensor article

Feb 9/10 - P0012 & P0022 - Camshaft Position - Timing Over-Retarded

Feb 2/10 - P0115 - Engine Coolant

Temperature Circuit Malfunction DTC

Jan 19/10 - P0105 - MAP/Barometric Pressure Circuit Malfunction

Feb 10, 2011 | 2004 Chevrolet TrailBlazer

1 Answer

My left rear speaker has no sound. All others work. I have tested the speaker on a different reciever and it works fine. My reciever is a integra DTR 5.5

Swap your left and right rear speaker over. If you still get no sound from the right speaker connected to the left speaker connection on the receiver, then you have a fault on the receiver output. Check your manual first to see if any setting switch off the rear speaker before taking the unit for repair or replace

Nov 26, 2009 | Integra Audio Players & Recorders

1 Answer

Low to no volume output from Integra DTR-5.2 receiver

most higher end integra's have a input level adjusment or input selection for each and every input. Perhaps you are not on the correct input, go to onscreen programming and check out the input level and input select - also try the tape in another input like tape 2 or cd. It will not hurt the receiver for a test. Also, if you are using the cheap cables from the manufacturer - try a pair of cables that you know work or go by some. BTW, you don't need to spend $40 for cables order them online through amazon or other store. Gold / sliver plated oxygen free are best.

Jun 30, 2009 | Integra DTR-5.2 Receiver

1 Answer

No sound from speakers from components with Integra 6.9 receiver

Turns out it had to do with one of the settings for the new Blu-Ray player.
Thanks anyway.

Jan 17, 2009 | Integra DTR-9.1 7.1 Channels Receiver

2 Answers

Japanese import integra type r stereo wiring diagram

Try the following, this is an 1997 USA Integra

Radio Constant Wire 12V+: Blue/White
Radio Switched Wire 12V+: Yellow/Red
Radio Ground Wire: Black
Radio Illumination Wire: Red/Black
Radio Dimmer Wire: n/a
Radio Antenna Trigger Wire: n/a
Radio Antenna Location: Left Rear
Front Speakers Size and Location: 5 1/4′ Doors
Left Front Speaker Wire (+): Blue/Green
Left Front Speaker Wire (-): Gray/Black
Right Front Speaker Wire (+): Red/Green
Right Front Speaker Wire (-): Brown/Black
Front Speakers Size and Location: 6 1/2′ Side Panels
Left Rear Speaker Wire (+): Blue/Yellow
Left Rear Speaker Wire (-): Gray/White
Right Rear Speaker Wire (+): Red/Yellow
Right Rear Speaker Wire (-): Brown/White
-->

Oct 06, 2008 | 1997 Honda Accord