Question about Kenwood Food Processors

1 Answer

Kenwood km266 schematic needed, problem: shut down afther reaching max speed,afters stop : same thing happens i susspect main board or tacho, any suggestions ? greetings Eddy

Kemwood km266 auto switch off

Posted by Eddy Van Waes on

Ad

1 Answer

Larry Ng

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Kenwood Master
  • 5,991 Answers

Moved you out of computers it is not.

well it can only be the parts inside, board and tach.
kenwood has no schematics, ask them yet, only they have them if ever. most do not.
its a throw away consumer device.
buy the cheapest part on ebay, replace it , if fail move to part 2.
and so on. lacking schematic and my nice scope very hard.

Posted on Sep 17, 2019

Ad

5 Related Answers

Open SKy

Carlos L. Burgos

  • 620 Answers

SOURCE: Need schematics or maintenance maual

What is the post here? any problem?

Posted on Nov 16, 2007

Ad

Anonymous

  • 9 Answers

SOURCE: mixer speed switch is haunted

Here is where you can download the repair manual. Read the section on speed control adjustments and repair. This might not be difficult for someone who is mechanixcally and electrically knowledgible.

Mike H.

Posted on Mar 25, 2008

protek480

Craig Butler

  • 1730 Answers

SOURCE: The generator starts up runs for about 15 seconds and shuts down.

Check the oil pressure switch



If you need further help, I’m available over the phone at https://www.6ya.com/expert/craig_3fa289bf857b1a3c

Posted on Aug 21, 2009

brian_carr60

Chris Spudulike

  • 63 Answers

SOURCE: tacho stops working on triumph speed triple 955i

Bad earth connection!

Posted on Aug 31, 2009

Anonymous

  • 124 Answers

SOURCE: need main wiring schematic for 2000 ultra classic

Looking at the plugs on the meter side of the harness: for the speedometer there is a three position plug. Pin #1 is Orange, Pin #2 is White/Green and Pin #3 is Black. for the Tachometer there is a six position plug, Pin #1 is Orange, Pin #2 is Pink, Pin #3 is Black/Yellow, Pin #4 is Green/Red, Pin #5 is Yellow/Red, Pin #6 is Black

Posted on Nov 17, 2009

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Power switch and or timer


More in likely the switch has over heated and is failing, needs to be replaced, if it can be? Or it just needs to be cleaned with Non conductive electronics contact cleaner...
really hope that helps?

Mar 09, 2015 | Food Processors

1 Answer

Won't start;


A possibility that the micro switch inside which is actuated when you put the top on......the one you are tooth picking....has become dislodged, or the grooves that the switch hold it in place have broken off. Is there anything rattling inside the mixer which would suggest that a piece of the casing has broken off. If you can disassemble it to this point where you can see the switch and there is damage around that area which makes the switch loose, you could use some hot glue to hold it firmly in place. Let the hot glue set solid before you use it.....especially as the switch completes an electrical circuit and hot glue in its liquid form s conductive! Always remember to remove the electrical connection before opening the unit. Failing this, it could possibly be that the switch needs replacing which is a far easier job. Switches are pretty comparable regardless of what brand mixer. Sometimes held in with a screw on opposing corners. So even eBay would probably have one. Good luck. On the bright side, your solution works, but on the dark side, using a plug socket to switch a unit off and on is tricky! Saranden.

Nov 24, 2013 | Cuisinart DFP-14BC Custom Food Processor

2 Answers

Sir, I have Molinex Food Peo of model 370.It has started giving noise when switched on. More over its safety switch is also broken. need to replace safety switch. I feel the carbon brushes have been worn...


Sir, I have Moulinex Food Processor of model Master Chef 580 .It has Problem with the Moulinex DG6 6.34 Cups Food Processor Sir, I have Molinex Food Processor Master Chef model 580.It has started giving noise when switched on. More over it's safety switch is broken. need to replace safety switch.Also Motor's Rotor's winding is burnt.Needs rotors replacement. Please intimate service center &spare part supplying agency in India. I am in Vadodara (Gujarat) India

Jan 19, 2011 | Moulinex DG6 Food Processor

1 Answer

My food processor has seized up and no one can open it to repair


if the screws are a star head, go to an auto shop T30 T40 T50
if their a 3 point screw head, find an avaiation tool supplier

Jan 27, 2009 | Moulinex DG6 Food Processor

1 Answer

Operating switch


You could try a shot of contact cleaner inside the guts of the switch. Perhaps over time some sticky residue has built up causing the switch to become frozen. Unplug the unit, spray inside the guts of the switch, work the switch back and forth. repeat unit the switch loosens up. BE SURE to use a contact cleaner that won"t damage plastics, will say on label!

Jan 09, 2009 | Food Processors

1 Answer

Broken Switch on West Bend High Performance food processor


We had this problem to but we were able to assemble with the help of a rubber band that held the switch on until the lid was locked in. Then you could use it the same way...pushing the rubber band down to engage the switch. I need to add though that since using this option...for nearly three months, The switch housing broke as well. I am now on the search for something to replace it I guess.

Nov 09, 2008 | West Bend 6526 Food Processor

1 Answer

The bowl will not unlock


with that type of bowl on closing the lid the switch open and on opening the switch close.the switch will not unlock because the switch itself is sticking or defected try cleaning the switch with some contact cleaner.if that does not work then you will have to take it to a small appliance tech for repairs.if there is no appliance tech i a sorry to tell you but you will have to settle for a new one.good luck.

Jun 05, 2007 | Cuisinart Limited Edition Metal MP14 Food...

Not finding what you are looking for?
Food Processors Logo

Related Topics:

243 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenwood Food Processors Experts

Ross Keen

Level 3 Expert

1364 Answers

Brad Brown

Level 3 Expert

18562 Answers

Andrew Taylor
Andrew Taylor

Level 3 Expert

35742 Answers

Are you a Kenwood Food Processor Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...