Question about JVC Car Audio & Video

1 Answer

While using my JVC KW-V830BT stereo it will turn off then back on again and after about 4 or 5 times doing that it will turn off then a screen will pop up saying “Please move the vehicle to a safe parking area and turn the ignition OFF then back to ON”. After I do what it tells me, it does the same thing all over again.

Posted by Courtney Freund on

Ad

1 Answer

Renee Knafel-Bullock

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Mentor:

    An expert who has written 3 tips or uploaded 2 video tips.

  • Expert
  • 357 Answers

Wow whoever put it in go take it back theres a problem in the wiring

Posted on Jul 03, 2018

Ad

5 Related Answers

tripletauto

TripleTauto

  • 1450 Answers

SOURCE: JVC KD-AVX1 parking break

your car probably wont have one this wire is designed to be hooked to the park brake switch wire so you cannot watch movies going down road.as this is illegal. the wire gorunds when park brake is pressed. splice it into the wire on brake

Posted on Jan 16, 2009

Ad

Anonymous

  • 2 Answers

SOURCE: have a jvc camcorder turn on and it says safe mode remove battery

Forget the battery, the mini dv carrage assy can get out of sync and initiate the safe mode, if you noticed a problem loading the tape or have heard a gear skip sound thats the problem. The best you can do with those camcorders is keep the tape in the camcorder!!!!! That will prevent the problem and insure many good years of recording.

Sorry,

Tim.

Posted on Jun 29, 2009

aneesh ch

Aneesh ch

  • 73 Answers

SOURCE: My Jvc Compact Camcoder (GR-SXM26EA) is stuck in safe mode

thats a hardware problem .u must to open that camera and remove mechanisum u can c there is a small board behind that mechanisum .remove that board and c there is rubeer which connec to caption motor . that u put right condition than it will work

Posted on Jul 11, 2009

Anonymous

  • 1 Answer

SOURCE: jvc kw-nx7000 not working after I tried to update the firmware

I just performed the update as well and ended up with the same issue. I'm hoping to drive my vehicle around to see if it will eventually detect the satellites.

I might recommend a couple of things. Not sure what JVC Support has recommended but you can try a hard reset. Button is located on the left bottom corner of the unit.

You could also attempt a factory restore. The option is located in the settings under your navigation menu.

Overall I like the unit as it seems to be a stable system., for customization and information related to what JVC considers to be propritory info absoultely sux!!! The backgrounds are hokey and screens could really use an overhaul. I have yet to find any really great solutions for working with the files and information and have started to learn on my own. Very slow going so far as I really don't want to brick the unit. If you or anybody else has a good solid recommendation other than the obvious for working into the file structure etc... please feel free to share!

Posted on Apr 20, 2010

Anonymous

  • 2 Answers

SOURCE: User Manual for JVC KW AVX 826

www.jvc.co.nz/assets/pdf-manual/KW-AVX826.pdf

Posted on Aug 04, 2010

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why does my new KW-V830BT by JVC cycle back to the start up screen when I am listening to music??


Did you turn the "demo mode" off after it was installed? It's in the menu setting.

Sep 28, 2017 | JVC Car Audio & Video

1 Answer

Jvc kw avx840 frozen on telephone screen. Press reset and everything works fine again until either detatch facia or switch off ignition.


Sounds very strange ... I have the exact same set. Try removing the Bluetooth dongle and re installing it again and see if this helps. Is this a new install? You r ground is good right? to the frame not just a black wire from old stereo you replaced?

Apr 21, 2014 | JVC Kw-Avx840 7 Double-Din Multimedia...

1 Answer

JVC KW-AV60 BT touch screen car audio touch screen not responding


is there a diagnostic setting for touchscreen calibration. Could have gone bad. you are probably still in warranty, take that bad boy back

Mar 12, 2014 | JVC KW-AVX800 CD Player

1 Answer

JVC KW-AV71BT wiring diagram


My ipod jack used to work, I unplugged ipod then plugged it back in. Now it shows on the screen that the ipod is connected and playing, but now sound comes out. This is only on ipod, everything else works fine

Feb 02, 2014 | JVC KW-AV71BT In-Dash DVD/MP3/USB 7"...

1 Answer

Whenever I apply my left signal turn, my screen flashes on my JVC kw av 60bt deck ,message -check for safety behind with your eyes


Did the vehicle come from the factory with a jvc stereo or did someone install it ?If the stereo was not installed by the factory whoever installed it hoooked up the power wire to the blinker power wire and if the factory did install it i would buy a new blinker relay .

Oct 19, 2012 | Cars & Trucks

1 Answer

How to set clock jvc kw-xc770 car stero


1 Press SEL for more than 2 seconds. One of the PSM items appears on the display. 2 If "PSM CLOCK H" does not appear, press fast forward and up or fast backward and down repeatedly until it appears. 3 Turn the control dial to adjust the hour. 4 Press fast forward and up or fast backward and down until "PSM CLOCK M" appears on the display. 5 Turn the control dial to adjust the minute. 6 Press SEL again to finish the setting.
http://www.jvc.ca/manuals/KW-XC770.pdf

May 05, 2011 | JVC KW-XC770 CD / Cassette Player

1 Answer

My screen is blank but the tuner is playing the radio stations


VC stereomag-glass_10x10.gif systems come in a number of different styles and models, from portable "boom boxes" to stereo receivers designed to be used with entire entertainment systems. When a JVC stereo malfunctions, it's a good idea to perform a few basic troubleshooting steps to correct the problem. Often, the solution is very simple, involving something you can correct immediately and which will allow you to continue using your JVC stereo system without having to call a repairman.

Aug 09, 2010 | JVC KW AVX820 Car Video Player

1 Answer

JVC KW-NT1 GPS not working in UK


Have you tried re-flashing the unit with the latest EU firmware update available from the JVC website? http://www.jvc-victor.co.jp/english/car/support/navi/nt1/eu/index.html Should overide the current firmware then allow you to use UK maps. If it doesn't work you can always reflash it with the USA update.

Nov 28, 2009 | JVC KW-NT1 Car GPS Receiver

1 Answer

KW-AVX-810


was simple i got in touch with as i do not have a manuel got lost some how so i got the diagram and was able to solve the problem infact its got a usb port at the back of the unite just pluged y ipod usb in
thanks

Jul 30, 2009 | JVC KW-AVX810 Car DVD Player

Not finding what you are looking for?
Car Audio & Video Logo

Related Topics:

1,342 people viewed this question

Ask a Question

Usually answered in minutes!

Top JVC Car Audio & Video Experts

xxxxxx xxx

Level 3 Expert

5023 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Muntejaya Ginting
Muntejaya Ginting

Level 3 Expert

10422 Answers

Are you a JVC Car Audio and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...