Check and replace the damaged component/s at its audio output section circuit board. If needy, replace this board as card basis. If you wish to get some details; check the site linked here. Pull up older posts. Search the site by type in the "brand name" to your device; in the "Search box at the top right of the display window of the Homepage" to get gathered related posts.
http://electronicshelponline.blogspot.com/

Oct 11, 2016 | Samson Resolv 65a Main / Stereo Speaker

1 Answer

Samson SX1200 - Protect light on. No blown output transistors.

Have you checked the power supply section? Also look out for any IC's in the amp stages. They can go causing that kind of fault.

Oct 11, 2014 | Samson SX1200 Amplifier

1 Answer

Power Supply XP308i

Read the manual. SamsonTech

Mar 30, 2014 | Hartke Samson Technologies - SAM-XP308I -...

1 Answer

My xp308i power supply indicator keeps flasing on and off and all the lights run up and down

see answer to your previous post

Mar 30, 2014 | Hartke Samson Technologies - SAM-XP308I -...

2 Answers

Hum from Samson XM610 Powered mixer

hi, my samson xm610 have a problem even i tern off the voluem of each chanel still have a sounds be fore is not just like that.. can you help me

Aug 27, 2012 | Samson Xm610 Powered Mixer

2 Answers

Speaker humms only. what causes that?

Incorrect connections or volume settings.

• In powering up, mixer first then amp

• In turning off , amp first then mixer

If hum still persist, without the mixer connected

then speaker amp may need servicing.

Jul 31, 2012 | Samson Auro D415A Speaker PA Active

1 Answer

65a Resolv studio monitors. The left one just blew out -- maybe. The blue LED stays dim, as though the monitor has been sleeping. When I power off the monitor, the speaker gives a loud pop, and the cone...

You are getting DC offset voltage on one of your amplifiers that is the reason the speaker pushes out and you might be hearing a humming noise too. Do not turn on the speakers till you get it fixed or else you would end up burning the speaker voice coil too.The dim blue LED is also an indication of a short circuit in the output stage.
Your left amplifier needs a output chip (IC ) replacement. You will need professional help to do that. Will cost you about 20$ plus service charges.

Jun 27, 2011 | Samson Resolv 65a Main / Stereo Speaker

2 Answers

Hey, i bought a new pair of samson auro D415 speakers and i connect them in parallel because one of my main mixer outputs ain't working.but even if al my signal gains and fader levels are low,the peak...

Check only one active speaker at the mixer output and report the results.
Connect only one of the audio inputs from the power amp at the mixer output (and the passive speakers at the output) and report the results.
Sometimes (in parallel connections) there are interferences from the volume controls.

In case of a problem or clarification or further details needed, don't hesitate to post me a reply before rejecting my answer.
If you are satisfied, rate my solution with the "thumbs" or (even better) add a testimonial.

Thanks and regards
Please kindly rate this solution
Stelios
direct fixya link: http://www.fixya.com/users/technical114

Mar 30, 2011 | Samson Auro D415 - 2-Way Active Speaker...

1 Answer

Hum coming from one speaker

Not good. you may have a blown amplifier. To check this, put a volt meter across the speaker terminals with the amp hooked up and off. Turn the amp on with the volume set to minimum and check for any voltage at the speakers. you should have no DC voltage (less than .1 volt) at the speakers. hope this helps

Jan 03, 2011 | Samson Resolv 65a Main / Stereo Speaker