Question about Generac Electrical Supplies

1 Answer

Son brought over his GP 8000E. Dog chewed up low voltage from control panel to engine. Can't find wiring diagram. Can anyone send me this, or a link? Thanks in advance.

Posted by John Henderson on


1 Answer

Brett Duxbury

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Master
  • 4,290 Answers


Posted on May 30, 2018


5 Related Answers


  • 193 Answers

SOURCE: Climate Control will not light up

Your best approach to this problem is to buy a 12 volt tester. Looks like an ice pick with an electric wire coming out of the top. Cost about $6.00 at any parts store.

Connect the metal clip to a good ground, turn the ignition switch on, then with the ice pick, touch each end of the fuse. Good fuses will light up when you touch them at both ends. A defective fuse will only light up on one end. Find and replace.

If you would like to contact me again about this or other problems, feel free to do so.
ASE Master Technician

Posted on Nov 26, 2008


John Weathers

  • 409 Answers

SOURCE: Need Injection control unit wiring diagram MB W-124 1989 300E

Go to they have all the wiring diagrams there.

Posted on Feb 13, 2009


  • 1 Answer

SOURCE: My dog chewed off the trailer + car wiring plug

Found this on the Wb


Posted on Sep 14, 2009


  • 7 Answers


Sauder and heat shrink

Posted on Oct 17, 2009


  • 1 Answer


Fuel pressure can be realese

Posted on Mar 02, 2013

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

94ford probe won't start

Well Sandra , the thing to do would be to get it to turn the engine over with the key , Then diagnose the no start problem . Look at a wiring diagram (do you know what that is ?) When you turn the key to start , the electrical part of the ignition switch sends B+ voltage to the starter interrupter relay through the clutch switch to the starter motor solenoid . Testing the electrical circuit with a DVOM - digital volt ohm meter with the help of a wiring diagram ,so you know where to test is the proper way to diagnose the problem . Not guessing ,an rigging the stuff . You can find free wiring diagrams here
Enter vehicle info. year , make , model an engine ! Under system click on engine ,then under subsystem click starting . Click the search button then the third blue link .
Electric Testing Techniques You Need to Know
Do you know what a relay is ?
VEHICLE RELAYS Testing from the relay base
VEHICLE RELAYS Operation Diagnosis
If you look at the wiring diagram you will see the relay is controlled by the CPU - engine computer .
How to voltage drop test starter motor circuit

Jun 29, 2017 | Cars & Trucks

1 Answer

Can anyone recommend a good brand of heated dog bowls?

Wal-Mart carries a heated bowl manufactured by Farm Innovators. It is relatively inexpensive, has an anti-chew cord protector and a built in thermostat. I will send you the link for this product; however you may want to do a little comparison shopping of your own.

Aug 26, 2012 | Alessi Pets - Others

1 Answer

Ignition switch??? temperature guage not working- sending unit keeps blowing, also dash lights will sometimes go out. and when car is running, tilt the wheel down semi hard and will shut car off!! also...

Do you have a professional scanner ,do a scan of the whole vehicle . Instrument cluster , BCM , etc... Not OBD2 scan from autozone or advance etc.... thier tool can't check the whole vehicle network . The control module's on your vehicle all share information on what is called a serial data bus ,or communication network. ( temperature guage not working- sending unit keeps blowing, ) I don't think the sending unit is the problem , an it's not a sending unit . It's a engine coolant temperature sensor ,an it's a input to the PCM/ECM - engine computer . The engine computer send's this info. to the instrument cluster on the GMLAN data network . GM had problem's with stepper motors in the instrument clusters . The stepper motor control's the gauge needle.2003 to 2006
How to repair GM Instrument Cluster Speedometer Gauge Stepper

Also sounds like you have wiring harness issue's ,finding an viewing wiring diagrams an using a DMM - digital multi-meter to test affected circuit's is the way to a fix. Not guessing !

Electric Testing Techniques You Need to Know
The Trainer 32 How To Read An Automotive Block Wiring Diagram
Mastering Voltage Drop Testing with Pete Meier and Jerry Truglia

Free wiring diagrams here Enter vehicle info. year , make , model an engine size. Under system click on lighting ,then under subsystem click on headlamps . Click the search button then the blue link . Looking at the diagram you will see the headlamp / multifunction switch is a low voltage input to the BCM - body control module , do you know anything about automotive electronic's ? The high beams are contolled by a relay energized by the BCM . Check through some of the other wiring diagrams ,for the dash light's , pull the instrument cluster an check connection's ,power & ground circuit's etc...

Nov 27, 2017 | 2006 Chevrolet HHR

1 Answer

I need a wiring diagram for a mini Jazzy 1143 power chair. The controller cable was chewed in two by a dog and ther seems to be more wires than connection points.

I think it would be easier for you to contact pride mobility or your provider and have then send you a new cable. If Medicare purchased your chair then they will pay for the repair Hope this helps

Aug 15, 2010 | Pride Mobility Products Health & Beauty

1 Answer

My dog chewed the thermostat wire by the compressor, i replaced the chewed wire now the thermostat won't turn on, therefore; no ac.. could it have blown a fuse? if so, where are they?

Either you have blown the low voltage fuse located inside the air handler (if there is one) or you have blown the transformer feeding the low voltage control wiring.

If the transformer is blown due to no fuse installed, I would recommend installing a low voltage 3A fuse in line with the red terminal coming off the transformer. This will protect the transformer in the future.

Aug 01, 2010 | Goodman CKL42AR42 Air Conditioner

1 Answer

2004 mustang check engine light,abs light,and traction controll lights all come on when car is stsrted

Low battery voltage codes can mean a blown fuse as well as a weak battery at cranking. You don't see any evidence of rodents chewing on wire looms? The PCM should have stored more than low voltage codes if the "check engine" light stayed on.

Oct 25, 2009 | 2004 Ford Mustang

2 Answers

No tail light 99 suburban

ck wires not sockets sounds like ground problems

Sep 23, 2008 | 1999 Chevrolet Suburban

Not finding what you are looking for?
Electrical Supplies Logo

Related Topics:

90 people viewed this question

Ask a Question

Usually answered in minutes!

Top Generac Electrical Supplies Experts

Bill Johnson

Level 2 Expert

306 Answers

Fahr Quad

Level 3 Expert

774 Answers


Level 3 Expert

2601 Answers

Are you a Generac Electrical Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides