Question about Haier Washing Machines
I watched the washer go through a complete wash cycle. Everything looks fine until it gets ready to do a spin cycle. the water drains out okay. But then it beeps and displays UL, even without anything in it. The clutch pawl retracts, and then reengages the ratchet. The machine then sits there doing nothing for a few minutes before throwing the UL error code. Any ideas on what the problem is and how to fix it?
Take the 4 screws out of the top section, lift up the whole top. You will see a bar. You must lift the top so the bar raises above the drum. Take the screws out of the plastic cover and check the bar .it has 2 round ends that rest in two holes. If it came out of one simply place it back in the hole. You will hear it click when pressing it. Put back together. Problem solved.
Posted on May 15, 2019
I have the same problem they can not fix it so dont waste your money on a repair guy they just run it through a dianostic test and tell you that you are no using the machine properly
Posted on Mar 14, 2007
SOURCE: UL Code
Solved the unbalanced problem - open the top of the machine (press in with a flat putty knife about 3" in on the front on each side while lifting up as there are 2- 1" wide catches). Once both sides are unlatched, raise the lid then slightly lift the rear of the lid so that it fits into the curved part at the top of the hinges then open all the way - tape the lid to the top so it doesn't flap about and scotch the lid to keep it from falling back down on you. Now, look around - see all that rust? The rust has fallen into and gotten underneath one or more of the 4 white plastic suspension "ball joints" which have probably totally dried out by now from their factory grease because of the water, bleach, and rust particles. Having someone help you, simply lift up on one of the 4 corner suspension rods - gravity and weight is all that holds them down. The white ball will lift out of the socket and still be attached to the rod. Clean out the rust, lightly sand the "socket" with emery cloth, then slop in a fingerful of grease. I used automotive wheel bearing grease with graphite in it. Also scrub off all embedded rust on the white plastic ball. Lower that corner back into the newly cleaned and greased socket and repeat for the other 3 corners. Now when you move the tub around notice how the balls pivot in their sockets like they are supposed to. When they were dry and rusty they wouldn't move enough to allow the tub to twist like it should so it slammed around. Now, shake your head in disgust that after only 2 years there is so much rust that you wonder if it will make it another year before falling apart, close the lid, and try another load. That totally solved my off-balance problem where even a single handkerchief would give the UL error. It is still a finicky machine, but at least once again works like it did when new.
Posted on Jan 06, 2009
take the lid off attached to the inlet valve to the dispenserr you will see a little white mechanisim in line with them. this is called your flowmeter take it off and blow through it is should sound like a cazoo. put it back on and try to do a wash cycle. if this doesn't help you need a new flowmeter. also if you take the kick panel off you will find the tech sheet to help you diagnose this problem.
Posted on Jun 23, 2009
Tips for a great answer:
Mar 01, 2016 | Whirlpool Washing Machines
Jan 05, 2016 | Washing Machines
Jun 09, 2015 | Hotpoint WF430 Front Load Washer
Apr 09, 2010 | Whirlpool Duet GHW9150P Front Load Washer
Dec 03, 2009 | Kenmore Washing Machines
Jul 19, 2009 | Maytag LSE7806A Top Load Stacked...
Dec 31, 2008 | Fisher and Paykel Fisher Paykel Intuitive...
Nov 19, 2017 | Washing Machines
4,440 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: