Washing Machines Logo

Related Topics:

Question about Electrolux Washing Machines

1 Answer

The Electrolux washer extractor model W4400H keeps spinning at a low speed at the end of the program and the door lock stays engaged. Kindly advise

Posted by Prakash Viswanathan on

Ad

1 Answer

Wilson Andrew

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

W4600h is washing but not spinning

Posted on Nov 30, 2020

  • Wilson Andrew Nov 30, 2020

    W4600h is washing but not spinning

  • Amardeep
    Amardeep Mar 30, 2022

    My washing machine model w4660h whash time good work but last time no spinning I apply to 999 they also same last minute not spinning.

×

Ad

5 Related Answers

cpldw48

Dw Wooten

  • 227 Answers

SOURCE: Kenmore He 2 Plus washer door is locked and unable to open

unplug the washer an the door will open

Posted on Apr 25, 2010

Ad

Anonymous

  • 1122 Answers

SOURCE: Door Lock

on your model all wax motor door latch's have to be replaced,go to repair clinic .com and you can order the part or go to ebay,and put in maytag neptune mah5500bww wax motor and it will come up and the guy selling the motors has pictures on how to install,let me know-mike

Posted on Jun 25, 2008

Anonymous

  • 116 Answers

SOURCE: fwt449gfs2 washes, empties some water, does not spin, knob does not advance

There are two possible causes of the machine not going into the spin.

The first is an obstruction in the drain pump. This can be a partial block caused by a loose coin or bobby pin. The only way to clear the obstruction is to remove the lower panel at the front by removing the 2 screws at the lower edge. This will allow the front panel to drop down. You will need to unplug the machine for the naex part.

Now this will get a little messy... Be sure to have a lot of towels nearby to sop up the water. On the lower right hand side there is a pump with a black bellows attached which is also attached to the bottom of the tub. This black hose is clamped to the front of the pump if you unclamp the hose the remaining water in the system will spill out and you will have to reach inside the bellows and remove whatever obstruction is inside. some models will have a trap inside which may have to be removed from the top of the hose assembly by unscrewing the clamp on the bottom of the tub.

The hose will have to be reattached in teh reverse manner. It can be quite tricky to do so... Once the machine is back together you can test it by running a straight spin cycle, it should go into the full spin with no water in the system.

The other cause could be a faulty timer which may need to be replaced.

Posted on Aug 06, 2008

Anonymous

  • 481 Answers

SOURCE: Whirpool Ultimate Care II washer Imperial Series spins at low speed

it sounds like a worn clutch. ab164bf.jpg

40d1158.jpg

Posted on Aug 12, 2008

Anonymous

SOURCE: front loading lg washer

if you have the spin sense option, try enbaling that on the washer

Posted on Nov 04, 2008

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Electrolux Washer Extractor W4600H. Washing machine not spinning.

Question edited for full make model (what it is) and English.
Question moved to better category.

Special problem for Indonesian machines

https://www.google.com/search?q=Electrolux+W4600H+not+spinning

..
0helpful
1answer

I have electrolux w4400h washer/extractor displaying "door lock" error. I have checked the switch S3. its working well. What else should I check.

The white actuator box on the door locking mechanism is faulty. its already locked yet the machine door is open.
0helpful
1answer

Discharge Outlet Size W4400H Washer Extractor

Installation manual Washer extractors W4400H, W4600H, W4850H ...

www.opl-ltd.co.uk/extradocs/Gen4000%20Installation%20W4400H.pdf
Jan 31, 2011 - W4400H. W4600H. W4850H. W41100H. 400. 600. 850. 1100. 920. 980. 1220 ...Dimensions. 1 Control ... The washer extractor is supplied bolted in place .... The connector for the machine discharge (A) has ... outlet. Make sure that the hose's function is un- affected by the tilting function if the machine has
0helpful
1answer

Electrolux washer error code E42

The E42 error indicates a problem with the door lock mechanism. If the door was closed, did you hear the lock attempt to engage? If you heard the lock, check the door strike. If the strike is good, replace the door lock. If the lock didn't attempt to engage, check the wiring between the door lock and the control board. If the wiring is well seated and the wires have continuity, replace the door lock. If the replacement lock doesn't solve the problem, then replace the main control board. (You should find a diagram with the wiring inside the unit near the control board.) If you have broken wires in the wiring harness, replace the wiring.

Please add a comment with the model of your washer if you want me to point you to any parts/price lists.

I hope this helps.

Cindy Wells
0helpful
1answer

I cant get child lock off zanussi 6kg 1200 and cant find the manual please help

Zanussi has several washer models with 6 KG capacity 1200 RPM spin speed specifications. You need the model number to find the manual here: http://www.zanussi.co.uk/support/manuals/ . The model number for a front load washer is inside the door on the lower right of the opening.

For the ZWG7120P, you need to press and hold both the Temperature and the Spin buttons for 6 seconds to toggle the lock on or off. (This time is approximate.) These are the two buttons closest to the program selector dial. There is a small padlock icon in a curved line below and between the buttons. The direct link to the manual for this model in English is http://www.electrolux-ui.com//DocumentDownLoad.aspx?DocURL=2010\132\948930EN.pdf .

I hope this helps. Please add a comment with your washer model if the above child lock directions do not work on your machine.

Cindy Wells

Cindy Wells
2helpful
1answer

All cycles are working except the spin cycle. I have visually inspected the wiring connections and motor and dont see any obvious issues. There are no error codes and the LED lights seem to be functioning...

Because of the high spin speeds of front load washers, the doors are equipped with a latch and lock mechanism to prevent the door from being opened during the washers operation. These locks will often be actuated by a solenoid or wax motor to ensure they remain latched during the wash cycle. This model uses a two stage lock that latches the door when the load starts, and then when it is time to spin, the second lock engages to ensure the door is properly secured prior to beginning the spin. When this second lock engages, it also closes a set of switch contacts (the auxiliary door switch) telling the control board the door is closed and locked. If for some reason this switch is not closed, the washer will tumble during what would normally be the spin cycle until the entire cycle is complete.
0helpful
1answer

Model fwt645rhso will agitate but won't drain out, on spin cycle washer spins one way, stops goes back the other way, but water will not drain out. Does not rapidly spin on final cycle. Any...

There's an auxiliary switch in the door lock.switch assembly that is activated at the end of the wash cycle for the machine to advance to the spin cycle. The machine will NEVER advance to the spin cycle unless the auxiliary switch is activated as a safety feature to prevent the door from opening during a high-speed spin cycle that may result in physical injury. The drum tumbles back and forth while the machine control checks the auxiliary if activated but since it's not, the control will not command the motor speed control to spin the drum at high speed. These symptoms may indicate a faulty door lock/switch assembly and may need replacement. Click on the links below for the detailed troubleshooting instructions and replacement of the door lock/switch assembly.

Electrolux and Frigidaire Washers Door Lock/Switch Assembly Troubleshooting

Replacing the Door Lock/Switch Assembly on Electrolux and Frigidaire Washers
2helpful
1answer

My electrolux 880 front loader won't spin anymore

One of two things ... door lock or a speed board... I have been a tech for 10 years and I can say 9 times out of 10 its the speed board ... Its the board down by the base of the washer
5helpful
2answers

My Frigidaire front load washer doesn't spin, it turns during the wash cycle, doesn't show an error code, but doesn't spin the load at all, it is model CLTF2940ES0. Is it something simplet to fix?

Hello,

Welcome to FixYa.

Based on what you've described,...you likely need a door lock/switch assembly. The closest I found to your model is actually CLTF2940ES0.

The door latch is likely the single most common fault (which prevent's any spin, and consequently drenching wet clothing at the end of the cycle) with the frigidaire/electrolux built washer's, aside from pump's being obstructed.

I think it fool's many people because the lock indicates it is energized on the panel, however the built in "monitor" switch inside the assembly fail's. I do see a lot of these particular machine's...unfortunately.

You should be able to purchase one at most local brick
Not finding what you are looking for?

Open Questions:

227 views

Ask a Question

Usually answered in minutes!

Top Electrolux Washing Machines Experts

Brad Brown

Level 3 Expert

19163 Answers

David Shaub

Level 3 Expert

2994 Answers

Cindy Wells

Level 3 Expert

6554 Answers

Are you an Electrolux Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...