I need the factory wiring radio color codes to a mazda 626 99 es so i can hook up my new alpine deck

Question edited for clarity.
Question moved to model category.

https://www.google.com/search?q=metra+wiring+harness+diagram

and

2016 1500 radio wiring diagram

DODGE RAM FORUM https://www.ramforum.com > ... > Audio & Electronics
Oct 7, 2017 - Hi, After being convinced to put in an amp, I need some help wiring my Audio control Lc6i. I have the base system, not the Alpine .

2016 non alpine speaker wiring schematic
Jul 12, 2018
2016 RAM 1500 Wiring Diagram
Feb 2, 2023
More results from www.ramforum.com

Dodge Ram Radio Wiring Diagram

Pinterest https://www.pinterest.com > Explore > Vehicles

Mar 19, 2022 - Dodge Ram Radio Wiring Diagram ' Diagram, Dodge ram, Dodge dakota.

Dodge (2014-2016), Jeep, VP4 NA 52-pin Head Unit ...

PinoutGuide.com https://pinoutguide.com > Car-Stereo-Chrysler-Fiat

Dec 13, 2021 - OEM radio stereo wiring. Hardware connector pinouts and cables circuits ... Dodge Ram Truck 1500 (2013 - 2016), Ram Truck 2500 (2013 - 2016) ...

..

Re wire the radio from the battery to the speakers that way u won't get any more problems

The original radio is a BOSE system and it has a buit in amp. So if you replaced the deck you need to replace the speakers all so. Don't cut the wires to hook-up the deck buy an addapter KIT. It's not just the stereo that runs though that harness the factory alarm does all so and that will cause you problems. Anyway back to the stereo you need to add an amplifier and problem sovled.

When I change a stereo to an aftermarket one, I get a harness from Best Buy or Ebay.com that has all of the wires color coded and labeled for easy hook up to the new radio deck.

The player or radio coming out should have a sticker on it with a diagral. If not, the only two you need to worry about is the red and bla. They are the hot and grd. and are larger than the speaker wires. Get those two hooked up, put in a cd and turn it on. Then match up the speaker outputs to the correct speaker. Should be only one wire per speaker. If not, All speaker grounds are the same color and markings. Good Luc, Ned

Radio Constant 12V+ Wire: White/Green
Radio Switched 12V+ Wire: White/Red
Radio Ground Wire: Black
Radio Illumination Wire: n/a
Radio Dimmer Wire: Red/Black
Radio Antenna Trigger Wire: n/a
Radio Antenna Location: Rear Glass
Front Speakers Size and Location: 6 1/2′ Doors
Left Front Speaker Wire (+): Blue/Green
Left Front Speaker Wire (-): Gray/Black
Right Front Speaker Wire (+): Red/Green
Right Front Speaker Wire (-): Brown/Black
Rear Speakers Size and Location: 6′ x 9′ Rear Deck
Left Rear Speaker Wire (+): Blue/Yellow
Left Rear Speaker Wire (-): Gray/White
Right Rear Speaker Wire (+): Red/Yellow

Constant 12V+ Blue/Yellow
Switched 12V+ Gray
Ground Brown (or your own wire to a metal grounding point)
Illumination Green
Antenna Trigger Black/Red

Front Speakers 4" Dash
Left Front (+) Pink
Left Front (-) Purple
Right Front (+) Green
Right Front (-) Blue

Rear Speakers 5 1/4" Rear Deck
Left Rear (+) Black
Left Rear (-) Yellow
Right Rear (+) Red
Right Rear (-) White

I a '83 camry, there are 2 seperate plugs that go into a factory radio.
One for Power/and front speakers, and the other for rear speakers.

Sounds as if you are missing part of the harness for the rear speakers (or it is shoved in the back of the dash unused by the previous install). If there is not an un-cut plug in the dash - your only course of action would be to run your own set of speaker wire to the rear.

See this picture... these are the plugs that should go into your factory radio....


Metra kit 71-1938 will go from your factory wiring directly into your factory radio.


Thanks for using FixYa - a FixYa rating is appreciated for my effort in answering this Freebie question.

Here it is.

1996 Ford Explorer Car Stereo Radio Wiring Diagram
Car Radio Constant 12v+ Wire: Green/Violet
Car Radio Switched 12v+ Wire: Yellow/Black
Car Radio Ground Wire: Black/Light Green
Car Radio Illumination Wire: Light Blue/Red
Car Stereo Dimmer Wire: N/A
Car Stereo Antenna Trigger: Orange/Blue
Car Stereo Amp Trigger Wire: Blue (If Equipped)
Car Stereo Amplifier Location: N/A
Front Speakers Size: N/A
Front Speakers Location: N/A
Left Front Speaker Positive Wire (+): Orange/Light Green
Left Front Speaker Negative Wire (-): Light Blue/White
Right Front Speaker Positive Wire (+): White/Light Green
Right Front Speaker Negative Wire (-): Dark Green/Orange
Rear Speakers Size: N/A
Rear Speakers Location: N/A
Left Rear Speaker Positive Wire (+): Gray/Light Blue
Left Rear Speaker Negative Wire (-): Tan/Yellow
Right Rear Speaker Positive Wire (+): Orange/Red
Right Rear Speaker Negative Wire (-): Brown/Pink
-->

1990 Mazda 626 Car Stereo Wiring Diagram
Car Radio Battery Constant 12v+ Wire: Blue/Red
Car Radio Accessory Switched 12v+ Wire: Blue/White
Car Radio Ground Wire: N/A
Car Radio Illumination Wire: Red/Black
Car Stereo Dimmer Wire: N/A
Car Stereo Antenna Trigger Wire: N/A
Car Stereo Amp Trigger Wire: N/A
Car Stereo Amplifier Location: N/A
Car Audio Front Speakers Size: 4′
Car Audio Front Speakers Location: Dash
Left Front Speaker Positive Wire (+): Blue
Left Front Speaker Negative Wire (-): Blue/White
Right Front Speaker Positive Wire (+): Blue/Red
Right Front Speaker Negative Wire (-): Blue/Yellow
Car Audio Rear Speakers Size: 6 1/2′
Car Audio Rear Speakers Location: Side Shelves
Left Rear Speaker Positive Wire (+): Blue/Red
Left Rear Speaker Negative Wire (-): Blue/Green
Right Rear Speaker Positive Wire (+): Blue/White
Right Rear Speaker Negative Wire (-): Blue/Green

First we need to eliminate some possible install errors,
1.) is the deck turning on.... if not check to be sure power wires are hooked up correctly ,..... if deck is turning on and speaker wires are hooked up properly, this problem is usually caused by not hooking up the power wire to the factory amp, I'm not sure what color the wire is as they are different with many types of cars, as soon as you locate the wire hook that wire to your ignition wire to your raido usually the red wire coming out of the back of the deck.... when you are finished you should have your ignition power wire feeding power to the radio and the factory amp