Question about Husqvarna Sewing Machines

1 Answer

Code for classic collection sampler for my designer diamond Husqvarna Viking sewing machine Please heip

Posted by Betty DeBenedet on

  • Anonymous Jun 19, 2019

    If you have the "sampler" CD for your Diamond, The classic collection is already there for you. It's the exact same files....about 175 designs. These are all from past designs going back to around 1997 (#1+ & Rose)...….If you don't have the CD, simply go to the web site and download the Ruby Royale Manual by going to the Ruby Royale Machine. Once you download the manual, go to page the bottom, there is the code, and it's case sensitive when you unzip the file...enter that code, and make a note of it for the future.



1 Answer


  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has achieved Level 3.

  • Master
  • 851 Answers

Contact husqvarna directly for that. no one else has the code for your machine.

Posted on Mar 25, 2018


5 Related Answers

Russ Blakeman

  • 87 Answers

SOURCE: Threading a husqvarna viking 3610

This should be your machine: shows that they have this downloadable in Adobe PDF format here:

#37 in the list as of me posting this. You can get a CD version too but you'll just pay more and wait longer for the same thing. Once you have it print the manual (preferably both sides to keep it small) ang you'll have it. You can also peruse eBay to see if anyone is selling a manual but I doubt that will yield regular results. The machine looks to be pretty basic and standard but it's best you have the manual to get the most out of the machine. Also be sure to check the cleaning and lubrication section and go through the process so that the machine is in top working order before you put it into regular use - saves a lot of headaches.

Posted on Apr 28, 2008



  • 8 Answers

SOURCE: Need manual for Scandinavia 200 sewing machine

I have one.

Posted on May 25, 2009


  • 196 Answers

SOURCE: I need the driver installation for my reader/writer d-card

Drivers are on the installation disk. 3D will have it on cd#1 and 4D on the dvd. With the disk in the drive, plug the dCard reader/writer in and use the "add new hardware" wizard to allow the drivers to install automatically. Now,either repeat this for each usb port or remember to always plug in to the same port.

Posted on Sep 06, 2009


  • 371 Answers

SOURCE: husqvarna sewing machine - viking 400

Take to authorized Husqvarna Viking dealer for repair. This is not something that can be done by the owner. Check Husqvarna Viking website for dealer closest too you.

Posted on Sep 24, 2009

Norm Himebaugh

  • 152 Answers

SOURCE: Sewing thick fabric and machine won't send it through

Sergers are not really meant to sew very thick material. The blades have a maximum amount of range, or thickness that they can reach to cut. If you go outside that range, get ready for a big repair bill! You can break loopers and even the needle plate when you "push" a serger. My advise would be to use you sewing machine for the, "pounding" work. The type of material matters too, A thick Quilt like fabric can be sewn becatuse it's not dense material. A thinner harder denim could max out at 3 layers because of it"s hard finish. If the fabric you're sewing isn't dense like, you could just need new knives.

Posted on Oct 14, 2009

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Machine needs to rest message

When you see this message, wait until the OK message is enabled. Tap the OK button and then resume sewing. This message occurs often enough to be listed in the manual under Pop-up messages in both the Sewing and Embroidery section. (That starts on the last few pages of each of these "chapters".) Turning off the machine while this message is displayed may cause on issue with the on-board computer.

For the Husqvarna Viking Designer Diamond Royale, you can find the manual on the product page: . The direct link to the manual is . The pop-up for the Machine needs to rest is shown on pages 4-26 and 8-14 (pages 74 and 123 of the PDF). The Designer Ruby Royale has the messages on pages 4-24 and 8-14 (70 and 116 of the PDF). The manual for this machine is here: .

I hope this helps. If the message comes up after a few minutes of sewing (under 5), I would recommend that you consider cleaning the bobbin area. Sometimes a flossing swab can help remove debris that has gotten into the corners below the bobbin. If that doesn't help, your machine may need to be serviced.

Cindy Wells

Nov 22, 2017 | Husqvarna Sewing Machines

1 Answer

How to set the bobbin case in Viking Diamond machine

Hello Ann Thomas

Refer to the Designer Diamond manual section 10:2, page 124. You can download the manual for free here:

And here is an excellent youtube video:

Please let me know how it goes for you.

Happy Stitching

Mar 07, 2017 | Sewing Machines

1 Answer

Tension releases randomly on viking designer diamond

Check for loose threads in tension disks. If none, tension disks will probably need to be replaced. This part has a 5 year warranty if you are the original purchaser and purchased from an authorized husqvarna viking dealer.

Apr 04, 2014 | Husqvarna Sewing Machines

1 Answer

Husqvarna Viking Designer Diamond I get the following error code: Remove any thread under the stitich plate and in bobbin area.

Can you get any other codes in the window or is this the only one that keeps showing up? You may need to put a new needle and bobbin in as they may have been damaged even slightly when things got tangled. Kate

Feb 04, 2014 | Husqvarna Designer I

1 Answer

Internal timer on Husqvarna Diamond

Sorry, this is information only provided to certified husqvarna viking service technicians. You can see the sewing hours in the user interface by going to the 'tools/set" menu.

Nov 05, 2009 | Husqvarna Designer I

2 Answers

Trying to embroider with the Husqvarna Viking Designer I and the thread either bunches up on bottom or pulls bobbin thread up through design giving a white design What can be the problem

your tension sounds like it is off. i had that problem on my husqvarna diamond and had to take it in to be reset. my tensions were off by 1/4 inch. hope this helps. also did you take out your bobin and bobin tray and clean it good. make sure there is no lint in there.

Oct 31, 2009 | Husqvarna Viking 1

Not finding what you are looking for?
Sewing Machines Logo

Related Topics:

342 people viewed this question

Ask a Question

Usually answered in minutes!

Top Husqvarna Sewing Machines Experts

Douglas Plant
Douglas Plant

Level 2 Expert

222 Answers


Level 1 Expert

19 Answers


Level 2 Expert

89 Answers

Are you a Husqvarna Sewing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides