Question about Kenmore Ovens

1 Answer

Kenmore electric range/ovens

Kenmore Elite Model 790.99129409. Receiving error code F-13 when Broil mode is selected. While this code is showing, no other oven selections (Bake) are available. When power is shut down and restored, I can obtain Bake, Convection & Pre Heat cycles as long as I do not select the Broil mode first.

Posted by Karl MIller on

Ad

1 Answer

Terry

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Kenmore Master
  • 11,377 Answers
Ad

5 Related Answers

Anonymous

  • 87 Answers

SOURCE: RBS305PDS single oven whirlpool

Replace the electronic module.

Posted on Jun 10, 2007

Ad

Anonymous

  • 288 Answers

SOURCE: GE Wall Oven - No heat (broil or bake)

On appliances like this only the heating elements use 220 volts. things like the clock, fan, etc use 110 volts. That is why some things work and other do not. Start at the breaker, sometimes a double pole breaker will have 1 side tripped, but will look perfectly fine. switch the breaker all the way to off then re-set. If nothing changes follow the power to the appliance remove the panel and look for some fuses, check to see if any are blown. Also sometimes the microwave will have a separate power source even though its built in to the same appliance. So that's not always a good symptom to follow.

Posted on Nov 11, 2007

Anonymous

  • 161 Answers

SOURCE: Electric convection oven keeps on producing heat

Probably a burnt out element shorting out to the frame. When the oven is on does the element glow evenly the entire length. Are there visible holes or pieces missing? The contactor could also be sticking.

Posted on Jun 29, 2008

Anonymous

  • 1 Answer

SOURCE: Oven will not heat up on bake broil or convection cook.

I justn encountered the same problem (Model KERS507Y). Haven't checked yet...but am suspecting the Thermal fuse. Have you solved the problem?

Posted on Apr 09, 2009

Daniel S

Daniel Scott

  • 4323 Answers

SOURCE: My GE double electric oven

Hi

If the error code still appears, then the problem is likely in the control module (circuit board) behind the keypad and clock. You'll need to remove the bezel to get behind the control panel. Remove the screws & lift the panel up about a half inch and pivot it forward toward you. The circuit board you can now see is the Control module. Check for the black square shaped components on this board, they may be burnt or the connection might be loose. Look for welded relay contacts on bake or broil relays. If this happens, replace oven control (also called clock or ERC).
Hope this helps... If it does please do not forget to accept the solution or post back for assistance.

Daniel

Posted on Oct 11, 2010

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Kenmore electric range/ovens


Most likely the clock / control or a thermal fuse if your model has one.

Oct 09, 2017 | Kenmore Ovens

1 Answer

My oven when turned on goes to F1 and the heat is like broil...only the top burner comes on????


Hello,Please use the chart to determine which stove you have. You will have to look at the model number. The first 3 numbers will be the series on the chart. In most cases an F1 error would require replacement of the electronic control. This part is commonly refered to as an EOC or ERC. However this type of repair is usually reserved for repair specialists.

KENMORE Range/Stove/Oven Fault Codes – 362 Series (General Electric)
F1 = Stuck Touch Pad Key - Replace Electronic Range Control (ERC).

KENMORE - 911 Series (General Electric/Roper)
F0-F1-FF = Failed transistor in Electronic Range Control (ERC).

KENMORE Range/Stove/Oven Fault Codes- 665 Series (Whirlpool)
F1-E0 EPROM Error - Electronic Range Control (ERC).
F1-E1 EPROM Error - Electronic Range Control (ERC).
F1-E2 U/L ERC Errors - Electronic Range Control (ERC).
F1-E3 Fuel Type Fail

Kill power 30 seconds-Cancel-Start/Enter-5 seconds-Should see “E” for electric-
“9” for gas-If code changes again-replace Electronic Range Control (ERC).

KENMORE - 790 Series Electronic Oven Control (Frigidaire)
F1 = Shorted Touch Pad = Electronic Range Control (EOC) Internal check sum error.
Runaway Temp = Replace Electronic Oven Control (EOC).

Kill power 30 seconds - if error returns - replace Electronic Oven Control (EOC).

Thanks

May 28, 2010 | Kenmore 40494 / 40495 / 40499 Electric...

1 Answer

Kenmore Elite slide in range model # C790-440732 keeps displaying error code F23 and oven will not work except on broil


I have the same problem with my Kenmore F23 code will not bake but the broil works?? What the heck?

Feb 07, 2010 | Kenmore Ovens

1 Answer

Kenmore wall oven keeps showing error codes f5 and f3. Unit will not say on.


oven went into E2 F3 oven code while cooking a chicken and broil burner came on turned off oven but broil burner stayed lit, then had to unplug

Nov 13, 2009 | Kenmore 47702 / 47704 / 47709 Electric...

2 Answers

Kenmore electric range - oven temp low and takes forever to heat


if lower element tests open with continuity meter then it for sure is bad. i would also check the wire ends that connect to the element and/or the control board, they could have loosened allowing a bad connection and low voltage to elementor burnt off.. most ovens do not use the broil element at all during the bake cycle, only during the broil cycle.. some however do utilize the broil element during baking, but at a lower wattage or something..
best of luck,
ttfn

Oct 25, 2009 | Kenmore 30169 Electric Single Oven

1 Answer

Stove-top works, oven showing all 888888 across the screen


You're stove must be perfectly fine, but the thing displaying all those options may have a problem. Try to get this fixed as soon as possible.

Jan 31, 2009 | Kenmore 40494 / 40495 / 40499 Electric...

1 Answer

My kenmore oven is beeping and will not stop. the display shows F-1.


Please use the chart to determine which stove you have. You will have to look at the model number. The first 3 numbers will be the series on the chart. In most cases an F1 error would require replacment of the electronic control. This part is commonly refered to as an EOC or ERC. However this type of repair is usually reserved for repair specialists.

KENMORE Range/Stove/Oven Fault Codes – 362 Series (General Electric)
F1 = Stuck Touch Pad Key - Replace Electronic Range Control (ERC).

KENMORE - 911 Series (General Electric/Roper)
F0-F1-FF = Failed transistor in Electronic Range Control (ERC).

KENMORE Range/Stove/Oven Fault Codes- 665 Series (Whirlpool)
F1-E0 EPROM Error - Electronic Range Control (ERC).
F1-E1 EPROM Error - Electronic Range Control (ERC).
F1-E2 U/L ERC Errors - Electronic Range Control (ERC).
F1-E3 Fuel Type Fail

Kill power 30 seconds-Cancel-Start/Enter-5 seconds-Should see “E” for electric-
“9” for gas-If code changes again-replace Electronic Range Control (ERC).

KENMORE - 790 Series Electronic Oven Control (Frigidaire)
F1 = Shorted Touch Pad = Electronic Range Control (EOC) Internal checksum error.
Runaway Temp = Replace Electronic Oven Control (EOC).

Kill power 30 seconds - if error returns - replace Electronic Oven Control (EOC).

Dec 16, 2008 | Ovens

Not finding what you are looking for?
Ovens Logo

Related Topics:

204 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Ovens Experts

Michael Thomas
Michael Thomas

Level 3 Expert

3053 Answers

Brad Brown

Level 3 Expert

18455 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Are you a Kenmore Oven Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...