Question about Boating

1 Answer

Impeller part no. for a 1987 force outboard model 507y7c

Posted by Levi M Hutchinson on

Ad

1 Answer

Kardoc

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Boating Master
  • 5,891 Answers

Check the owners manual https://www.manualslib.com/

Posted on Mar 14, 2019

Ad

5 Related Answers

Anonymous

  • 10 Answers

SOURCE: Mercury 20Hp impeller/water pump location

It is located inside the lower unit housing. They are fairly easy to replace. Most Mercury authorized service stations will charge around $120 for this task.

Triton72

Posted on Mar 26, 2009

Ad

Anonymous

  • 187 Answers

SOURCE: 4hp Force Outboard motor overheating

Its possible it sucked up weeds or a plastic bag it into the intake and dropped off when you shut it down.

Posted on May 13, 2009

crondike

  • 75 Answers

SOURCE: Force 90 outboard locked in forward gear after impeller replaced

i have fought with mine in the past also.
put lower unit and the control in neutral
remove all spark plugs and have a helper turn the fly wheel clockwise while you install the lower unit i had to use channel locks to put the lower unit to neutral
good luck i hope this helps

Posted on Jul 09, 2009

Testimonial: "Got it together. Thanks"

Anonymous

  • 86 Answers

SOURCE: how to replace impeller in a 1959 evinrude

Put engine in fwd gear. Then disconnect the shift linkage. Remove the bolts that hold the gearcase on and slide gearcase off of the tower. Remove the 4 bolts or screws in the waterpump housing and lift the housong off. Replace the impeller and reassemble in reverse order. Make sure that you get the water tube lined back up and you can twist the prop to line the splines back up in the powerhead.

Posted on Aug 09, 2009

ray gallant

  • 68282 Answers

SOURCE: can a 1987 90hp johnson force outboard engine be

Yes of course but they need flushed with fresh clean water after doing it .

Posted on May 24, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What year is my mercury outboard searial no 3768233


Check here, you'll need the horsepower and lookup the serial-number range...

http://www.iboats.com/basics/serial_number_year.html#mercury

Aug 31, 2014 | Mercury Impeller, Water Pump - for...

1 Answer

Boat impeller


Undo gearbox bolts,take off trim tab,undo bolt in trim tab cavity,disconnect speedo tube,pull off gearbox. You will see pump housing,undo 4 bolts,pull off housing exposing impeller,there maybe a clip on top of impeller depending on model,pull off clip then impeller.yamaha didn't make outboards in 75

Aug 25, 2014 | Boating

1 Answer

I need to install a water pump impeller I just bought this boat I think the impeller is dry rotted I found a new one in the boat and also how to install the gear oil in the lower unit and what wieght oil I...


Usually you just buy outboard motor gear oil and that does it. (about 70 to 90) I think. Usualy comes in a squeezy tube for injecting it under pressure.
It needs to be injected from the bottom drain hole and you force it in till it starts to come out of the top drain hole.
Most outboards work like that so I assume yours probably will.

Jun 14, 2010 | Boating

1 Answer

Can a 1987 90hp johnson force outboard engine be run in saltwater


Yes of course but they need flushed with fresh clean water after doing it .

May 23, 2010 | Light Outboard Motor Boat Bass Fishing...

1 Answer

Force 90 outboard locked in forward gear after impeller replaced


i have fought with mine in the past also.
put lower unit and the control in neutral
remove all spark plugs and have a helper turn the fly wheel clockwise while you install the lower unit i had to use channel locks to put the lower unit to neutral
good luck i hope this helps

Apr 09, 2009 | Light Outboard Motor Boat Bass Fishing...

1 Answer

4hp Force Outboard motor overheating


Its possible it sucked up weeds or a plastic bag it into the intake and dropped off when you shut it down.

Mar 16, 2009 | Light Outboard Motor Boat Bass Fishing...

1 Answer

Mariner 4hp outboard can't get engine off casing


the drive shaft goes down through the water pump impeller and I suspect that the problem will be in the pump
the impeller is rubber and if run dry will melt the rubber into the housing and bind up the shaft
Brute force is a last resort so get all the information you can from a service dealer mechanic

Nov 12, 2017 | 2004 Mercury Mariner

Not finding what you are looking for?
Boating Logo

Related Topics:

128 people viewed this question

Ask a Question

Usually answered in minutes!

Top Boating Experts

ray gallant

Level 3 Expert

68282 Answers

 vpsoccer
vpsoccer

Level 2 Expert

282 Answers

Andrew Taylor
Andrew Taylor

Level 3 Expert

32966 Answers

Are you a Boating Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...