Question about Food Processors
Take a look on amazon here Amazon com rival food slicer parts I hope I have helped. enjoy
Posted on Nov 22, 2014
I have a rival food slicer model number 1101/8. The gears on the blade broke. I need a whole new blade where can I get one.
Posted on Nov 25, 2008
Abtecparts.com/rivalslicers.htm
Posted on Nov 27, 2007
I am parting out a Rival 1101E (no sub-model number). I have a good blade 6 7/16" diameter. Fine as is; even better if sharpened, which can be done by most knife sharpening services.
I also have a used motor for this slicer; it powers up and runs fine, but has not been stressed tested.
I also have new suction cups to replace the rubber feet on all Rival slicer models. These are different than what came on the slicers orginally; but, fit well and work even better. I have many happy users of these suction cup feet.
Posted on Nov 23, 2009
email [email protected]
Can anyone describe the washer behind the blade that many slicers seem to be missing? If I know the size (thickness, inside and outside diameters) and material (felt, brass or???), I can very likely find a third-party source for replacements. According to my manual, the part is the same for 1101 and 1030 models, therefor, measurements from either model will do.
Blade and motor mentioned in Solution #4 are no longer available.
An idler gear, food tray, spur-clamp/food-pusher, blade-retainer & thumb screw set, and replacement rubber suction cup feet are available. email [email protected] for more information.
Food trays differ on the various sub-models; let me know the complete model designation (1101E, 1101E/1, 1101E/4, 1101E/5, 1101/4, 1101/8 use one style, 1101, 1101E/6 and 1101E/7 a different). It would be best to describe the slide rails and mounting method (springy clamp on or between rails and attached with clip) your slicer uses.
Idler gear and blade-retainer/thumbscrew set mentioned earlier are no longer available.
New rubber suction cup feet (set of 4) continue to be available; many happy buyers of these cups.
Regarding solution #6 and parts I have available: the only remaining parts I have are:
- thickness regulator for 1101 models
- sets of 4 NEW rubber suction cup feet that fit all of the metal Rival slicers (many other brands too); but not the folding plastic models.
A food tray and a thickness adjuster remain from my used/recycled parts offering.
New, rubber suction cup feet continue to be available in sets of four. I sell 50-70 sets per year so my stock is always fresh, with supple rubber.
how much for 4 suction feet to 53821, wisconsin. thnx chris
Inquiries about availability and prices: lallin at juno dot com
Inquiries about availability and prices: lallin at juno dot com
All of the recycled parts mentioned in my comment from a year ago are gone.
New, functional replacment parts are available as follows:
Newly manufactured rubber suction cup feet, sold in sets of 4; nearly 200 sets have been sold to very happy customers.
Replacements for the thumb nut used to secure the blade; look different but work well.
email [email protected] for more information
I am once again parting out a Rival slicer and have some desirable part to offer. As of 9/1/11 the following parts from a 1101E/3 are available:
-6.5" blade
-idler gear
-washer
-motor screw
-motor; runs strong - plastic and chrome housing
-food grip, aka spur clamp, aka food pusher
-thickness regulator
New, function replacements continue to be available as follow:
- suction cup feet, in sets of four
- thumb nut to secure blade; sorry, no blade stud, just a nut.
[email protected]
I now have washers suitable for use between the blade and blade backing panel. They are not original parts; rather they are functional equivalents. Also, now have functional equivalent blade retainer nuts (not the square shaft bolt), For information on these items, replacement suction cup feet (hundreds of very happy customers) or availability of used parts, please contact me at [email protected] mailto:[email protected]
In addition to the new suction cup feet I offer for most Rival 1101, 1005, 1010, 1015, 1020, 1025 and 1030 slicers, I also now offer blade washers. These are friction-reducing Mylar washers that mount between blade and blade head (backing plate) and are functional replacements for Rival part number 854-023. Mailto:[email protected] for more info.
New this week, threaded shaft for Rival slicers 1005,1010, 1025, 1030, 1101; $25 postpaid to US and Canada. Act fast, these sell quickly.
×
I believe I saw your desired part at www.abtecparts.com/Rival_slicer_1101.htm. I was looking for the washer behind the blade. I found a listing there, but the washer was marked no longer available. Not the case with other parts.
Posted on Dec 09, 2008
I contacted Rival via email because I too need the bolt that attaches the blade to the unit, model 1101E/7. Rival responded saying this part is not available. Furthermore they could not even give me the dimensions. They did offer a 25% discount on a new slicer, but Ebay has better deals. I would take the slicer to a local auto parts store and find a bolt that works, but that might not be safe.
Posted on Feb 25, 2010
I need a blade for a rival electric food slicer mod # 1030/7. Can't find one anywhere. Might just go buy a new slicer.
Posted on Dec 02, 2009
I was wanting to know if any one know where I can get a the tray the meat sits one?
Posted on Aug 08, 2009
I have a Rival meat slicer, model 1101-E - Like new, never used, with original book - I'm selling it for $25. 352 422 6946 - Scott Noffsinger at Scott Noffsinger.com - Will be going to ebay auction soon!
Posted on May 17, 2009
JATA Model CF1007, 230 V 90W Food Slicer. Type
TSK-962 The gear side that
connects with the motor drive shaft is approx 42 mm diameter with 40 gears,
width of this gear is 6mm, the length of the double gear is 32 - 33 mm, and the
gear on the other end is 20mm diameter with 20 gears, width of the gear is 8mm.
I require to replace the plastic gear that connects the
motor spiral drive shaft, to the cutting blade gear.
Posted on Apr 03, 2012
Motor will not run, need bushers
Posted on Nov 29, 2008
I also have the problem of needing a part. My 1101/6 has a broken idler gear. Other than that, everything is intact. I will sell the entire unit for spare parts to someone for $25 and $ 5 to ship in the USA.
E-mail me if interested at [email protected]
Posted on Feb 16, 2009
If you need suction cups just put a rubber mat under it
Posted on Mar 24, 2015
Anyone have suction cups for the rival food slicer?
Posted on Apr 05, 2012
If you are referring to the four rubber suction cup feet, not the single big one, then, yes. I offer a functional replacement. The cups I offer are black, not gray; but, otherwise are a direct replacement for the the screw-in rubber feet on many models of Rival slicers, grinders, choppers, etc. Email for more information; [email protected]
×
Please send me a phone number so i can order a blade for my meat slicer model#1101/8
Posted on Mar 06, 2011
I have the blade and whole unit minus the suction cup assembly to hold it to the [email protected]
Posted on Dec 17, 2009
32,392 views
Usually answered in minutes!
NEED THE STEEL SLICING
Need a replacement slicing blade
need replacement blade for rival food slicer model 1030
Looking for a repalcement Blade. Abtecparts.com no longer has repalcement blade available.
need replacment blade for 1101
The plastic disk on the slicing blade has broken and I need a new plastic disk. The metal part of the slicing blade is fine.
need new blade, the plastic teeth keep breaking
can't find anywhere and abtecparts.com site gives error site not found
Need a new plastic piece that holds the meat down while slicing for a model 1038
Has anyone found a place to buy a replacement blade for the 1101?
The plastic gears on mine broke.
Plastic gear binds, blade is fine but is it true that no replacement is availbale?
im looking for a part on the rival electric slicer 1101E/6. its a small wheel that turns the blade, The teeth are broken
I need the little plastic nut that holds the blade on - can anyone tell me where to find it?
I'm looking for a replacement blade for rival food slicer model 1101E, 63/8 inch blade. My gear broke and now this blade is useless. Thanks if you can help find a replacement blade.
Plastic gear ring on back of blade just broke, otherwise good (would consider selling rest of unit for parts if another blade is not available)
Stripped threads on gear on back side of blade.
I have two of them here at home......it's a dam shame that the plastic gears are all that wrong with it
I as well have the Rival food slicer and in need of blade for model 1101/8, otherwise unit is as good as new
i need a blade fer model 1030 foodslicer
I am looking for a replacement motor and blade for a rival slicer, model No. 1101E-04
I need a replacement blade for my Rival 1101/3. On one of the websites mentioned above it says no longer available. Does anyone know where I may get that blade. Mine works great other then that.
I need the idler gear for a Rival slicer model #1101#/3
Need an idler gear for my Rival slicer Model # 1101E/3
I recycle parts for models 1005 thru 1030 and 1101; I also have some newly manufactured, functional replacement parts for those models. To inquire about availability of what you seek mailto:[email protected]
Where can I find the feet for my Rival meat slicer?Mop 1101E/4
Looking for the Retainer piece for model #1030V
×