How do I pair a auvio Bluetooth wth iphone7 - Audio Players & Recorders

The poorly written manual says to hold the Play/Power button for five seconds at which time you will get the blue light, Then hold the Play button again for three seconds to enter the bluetooth pairing mode at which time you will see the alternating red & blue flashing light. Ignore all of that and just hold the Play/Power button for however long it takes to start the red and blue flashing sequence. That means the headset has entered the bluetooth pairing mode. Then make sure whatever device you are trying to pair has its bluetooth pairing mode activated and you will eventually see Auvio BTCHP on your device's pairing window. Select it and you should then be paired.

Hi, some times the units only allow one pair .

Dear Anonymous,

• Make sure Bluetooth is enable on all the devices your want to use.

• Remove this device and any other devices that are not currently in use. (I am assuming you are using a cellphone or tablet)

• You can either put both devices in "Discovery Mode" let them see each other and Pair them again. Or

• If they already "see" one another .Re-Pair them.

• If they do not generate their own code, try enter "0000" and

Pair

• As far as the device that randomly stop playing, it might the battery is being overcharged. Put it On let, it play or in use until the battery has run out of juice; then charge it fully and see what happens. If the battery charge too quickly, you might need another one or take it in for service. In case of the Auvio speaker, take it back to Radio Shack if that is where you bought it.

Best of Luck,
JP

1. Try playing other audio files. Ensure that audio can play fine from the same audio device when using a headphone.



2. If Step 1 is not the case, try listening to audio by connecting the speaker to the Bluetooth device using the Aux-in cable. This will isolate if it's a Bluetooth connection issue or not. Remember to disconnect/un-pair the Bluetooth connection first.



3. If the issue only happens when connecting via Bluetooth, do the following:
   1. Adjust the distance between the speaker and the Bluetooth device.
   2. Reset the speaker to its factory default settings. For instructions on how to reset your speaker, go to the product's support site to view the relevant knowledgebase article.
   3. Clear the current pairing entry from your Bluetooth device. For instructions on how to clear the pairing entries, consult the user's manual of your Bluetooth device.
   4. Try re-pairing the speaker and the Bluetooth device. For instructions on how to pair the speaker with the Bluetooth device, go to the product's support site to view the relevant knowledgebase article.
   5. To further isolate, try pairing the speaker with other Bluetooth device.


4. If the issue happens when connecting either on Bluetooth or Aux-in, please contact Creative Customer Support via email.

Note: Creative Bluetooth speakers do not need any driver to operate. You may need to update the Bluetooth driver of your computer's built-in Bluetooth adapter or your USB dongle. To determine whether your computer or USB dongle is updated with the latest Bluetooth driver, please refer to their user's guide or website for information.
http://support.creative.com/kb/ShowArticle.aspx?sid=90429

I think what you are asking is how to connect the headphones to the iphone via Bluetooth.
switch on the headphones Bluetooth....go to general settings in iphone ... Switch on iphone Bluetooth....then choose detect devices....when it finds the headphones... Click "pair" ...it will let you know if pairing was successful.once it remembers the device you won't need to do all that again next time you want to use the headphones.now and again you will need to charge the headset up.

There should be a button on the device to hold and then "connect" in the bluetooth settings on the Iphone. Once it says connect let go of the button on device.

In general, you can check
Apple -> System Preferences -> Bluetooth
and see if it appears there and you can pair it.

Alternatively, you can send Auvio a message at http://www.auvio.nl/Contact%20International.html

try reseting both devices

If your device is requiring a pairing code, enter 0000
http://demandware.edgesuite.net/aasr_prd/on/demandware.static/Sites-radioshack-Site/Sites-radioshack-Library/default/v1417219736581/Support/ProductManuals/4000452_PM_EN.pdf

How can I pair an auvio pbt500 speaker to my pc?