Question about Vacuums

1 Answer

My fax carpet cleaners brushes are not rotating

Posted by Brenda bunce on

Ad

1 Answer

Elton Price

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Corporal:

    An expert that has over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 10 Answers

Check the belt, you can buy them at any Home Depot or Lowes hardware store..

Posted on Nov 21, 2017

Ad

5 Related Answers

Anonymous

SOURCE: Bissell steam carpet cleaner

http://www.howtomendit.com/answers.php?id=76173

Posted on Sep 28, 2008

Ad

Pierre Curtis

  • 33 Answers

SOURCE: My power brushes on my

The brushes will only work if the handle is released and the ProHeat vacuum is running . There is a micro switch inside the lower handle that switches on the DC carpet brush motor. The DC power for the motor comes from a Bridge Rectifier on the PC Board. [email protected]

Posted on Jan 18, 2009

Anonymous

  • 1 Answer

SOURCE: Hoover SteamVac Dual V Carpet Cleaner # F7410-900

"I did some research online and the recurrent theme was a bad turbine assembly. Fortunately I was able to fix this myself which took about 2 hours (some reading) and little effort. The problem was with the turbine which is fairly simple and had a bearing that had rusted and froze up. Removing the cover proved to be more difficult than fixing the stuck bearing. This was mostly due to figuring out the correct screws to remove and finally discovering that the back of the cover (over the wheels) is not secured by fasteners but by pegs that "pop" out.

Once I had the brush assembly and Cover removed the turbine came out with the removal of some obvious screws and gently pulling the hoses from the assembly. After carefully opening the assembly housing I discovered the bearing problem and with a little lubrication and some new grease had it working in short order. Putting everything back together was simple as well."


this worked for me. although once i got in i just had to mess around with the gears and loosen them up. getting in was the hard part soo here you go peoples.

take off tanks

unscrew 6 screws fom underneath machine. look carefully

just underneath where the dirty tank goes right by the part that sucks everything up is a screw. unscrew it

pop off the switch for your spin scrub mode. it pops right back on.

make sure your locks for the tank are turned in

then the back just pops off. you might have to give it a good tug. there are no screws although it maight look like there is.

then pull off the grey part.

once inside it is pretty easy.

but if you have any questionbs email at [email protected]

i took off so many more screws than i needed to to get this figured out so dont do that.

Posted on Apr 03, 2009

runnoft

  • 29 Answers

SOURCE: bissell carpet cleaner brushes won't turn

Make sure you have released the handle, as if you wanted to push the machine forward. If the handle is locked upright, the brushes do not spin.

If they still don't spin, you may have a broken belt. Look carefully at the base, on each side. As I face the front of mine, on the right side of the machine, a small belt goes around one brush and a small cog wheel. On the left side, a larger belt goes around both brushes. If either belt is broken, the brushes will not spin. This can happen if you let gunk build up inside the clear plastic side pieces or around or above the brushes. It's very important to constantly be cleaning your Bissell. The belts can be ordered online and replaced. See your owner's manual.

Posted on May 29, 2009

rkintz

  • 190 Answers

SOURCE: the brushes do not rotate when cleaning carpet. Is

(1) Assure the Brush Control on the hood is NOT set to the OFF position.
(2) Remove the brush assembly by pulling/unlatching it from base on each side.
(3)Does one of the brushes have the drive pin present? It should be about ¼ inch square, and two inches long. It attaches the brushes to the drive mechanism

Posted on Oct 23, 2009

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Brushes don't rotate on proheat2X,


How to Replace the Belt & Brushroll on Bissell ProHeat 2X ...

? 2:11
https://www.youtube.com/watch?v=Jj_43IHz9U4
Dec 28, 2012 - Uploaded by eVacuumBags
How to Replace the Belt & Brushroll on Bissell ProHeat 2X Series Carpet ... How to Replace Bissell Deep Cleaner Pump Belt orBrush Belt - Duration: 1:44. ... Won't SPRAY solution Rollers spin Fixing Bissell ProHeat Carpet ...

Brushes Will Not Rotate Deep Clean Essential - YouTube

? 0:53
https://www.youtube.com/watch?v=gbEXY5jkWSc
Apr 9, 2015 - Uploaded by BISSELL
If your machine is turned on and in the upright position yourbrushes will not turn. ... How to Replace the Belt & Brushroll on Bissell ProHeat 2X Series Carpet ... Won't SPRAY solution Rollers spin Fixing Bissell ProHeat Carpet ...

bissell pro heat 2x brushes wont spin Questions & Answers ...

www.fixya.com > Forum > Tags
... bissell pro heat pet 2x and my brushes won't turn or operate... check the belt belts ok brushes won't turn/rotate turn dial on bottom front on the water tank to ...

Feb 03, 2016 | Vacuums

1 Answer

How do I know which way round the carpet control works on power vx pet


I don't have one of these but normally the hard floor surface will have a brush around an edge or all the way around in contact with the floor, and for carpet you will just have the normal rotating brush. The rotating brush is always there.

Oct 16, 2014 | Vax U89-P9-P Power 9 Pet Bagless Upright...

2 Answers

On hoover steam carpet cleaner, the brushes do not rotate on low or high settings.


Follow these steps if the Brushes Fail to Spin
•If the brushes on your Hoover carpet cleaner fail to spin, there may be a problem---some sort of blockage---with the suction or with the belt that turns the brushes.
Turn the Hoover carpet cleaner over, and inspect the brush area. Debris, strings, or pet hair may be tangled in the rollers, keeping them from turning. Use a pair of scissors to cut away any obstructions in this area. Flip the Hoover carpet cleaner back over, and turn it on to see if cleaning the rollers has solved the problem.
To check the belt, turn the Hoover carpet cleaner over, and remove the bottom plate screw with a Phillips head screwdriver. Investigate the belt area to see if it is broken or has somehow slipped off. If it is broken, you can order a part from Hoover.com or from many of the other online parts stores.
When the belt arrives, simply slide it on in place of the broken belt, reattach the bottom plate and turn the Hoover carpet cleaner right-side up. Turn it on to test your solution.

Sep 03, 2010 | Hoover SteamVac F5914-900 SpinScrub...

1 Answer

The brushes do not rotate when cleaning carpet. Is in carpet clean mode and will not rotate. I did clear the filter underneath.


(1) Assure the Brush Control on the hood is NOT set to the OFF position.
(2) Remove the brush assembly by pulling/unlatching it from base on each side.
(3)Does one of the brushes have the drive pin present? It should be about ¼ inch square, and two inches long. It attaches the brushes to the drive mechanism

Oct 22, 2009 | Hoover SteamVac Carpet/Upholstery Deep...

1 Answer

Brushes wont rotate


the belt has streached go to walmart and get a new one.

Aug 13, 2009 | Hoover SteamVac Carpet/Upholstery Deep...

1 Answer

Bissell proheat 2x carpet cleaner


Normal 0 MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman";} Hi,

Here is a tip that will give you all the information you need to fix your Bissell Proheat Vacuum Problem.

Bissell Proheat Upright Wet/Dry Vacuum Problems

heatman101

May 30, 2009 | Bissell 9500 ProHeat 2X CleanShot Upright...

1 Answer

Hoover Steam VAc carpet Model F7425-900


Take out the brush block, make sure that the shaft is ok, it goes up into the turbine, which is what drives the brushes. If the shaft is ok, then the turbine either needs to be cleaned and lubed, or replaced.

Jun 01, 2008 | Hoover SteamVac Carpet/Upholstery Deep...

Not finding what you are looking for?
Vacuums Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top Vacuums Experts

AskDyson
AskDyson

Level 3 Expert

2572 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18429 Answers

D. Floyd Kolb
D. Floyd Kolb

Level 3 Expert

43501 Answers

Are you a Vacuum Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...