Computers & Internet Logo

Related Topics:

Question about Power Computers & Internet

1 Answer

How can I reset my Arlec Remote Controlled Power Outlet Model RC210

It has 4 separate on-off A,B,C,D The problem is they won't switch on and off separately. Is there a way to reset them back to factory settings and start again. Bought them from Bunnings.

Posted by David Whitehead on

Ad

1 Answer

Ian Mackereth

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 14 Answers

Unplug switch, plug in and while the LED is flashing, press and hold the All/turn off button. The LED will flash quickly, then it's unprogrammed when you plug it in again.
(This is in the instruction sheet, BTW)

Posted on Dec 02, 2017

  • 1 more comment 
  • David Whitehead
    David Whitehead Dec 02, 2017

    Thanks. Solved my problem first go.

  • hurch1975 Sep 24, 2019

    Best ever! Fixed!

  • Lee Woodward
    Lee Woodward Oct 07, 2022

    You are a gifted human. Fixed & Thank You

×

Ad

5 Related Answers

Anonymous

  • 1847 Answers

SOURCE: Printer Problems LEXMARK 5100 Series - 5150 model

this link will help you ...

http://www.lexmark.com/publications/pdfs/techref_WB.pdf

Thanks for using Fixya

Posted on Jul 03, 2008

Ad

Anonymous

SOURCE: MAXDATA Laptop Model Number L55110 reset factory settings

Reset the cmos (bios) by taking out the lithium battery (obviously disconnect from power first) and leave it for 10 minuets. You will need to reconfigure the settings in your bios afterward. If you still have the problem you will have to look to hardware problems, which could be various ones.

Posted on Jul 11, 2008

benbailey50

Francis Ben Bailey

  • 6 Answers

SOURCE: i cant get my remote reverted back 2 factory settings because it wont work at all because its the player is set in dvd 3 and the remote is not ....so how do i reset it if it wont work at all

If your unit is displaying DVD2 on the front panel, you will need to set the command on the remote to match the display on the unit.
Point the remote to the unit and press 2 on the remote. Them press system menu on the remote, you should be ok.

Posted on Jun 15, 2009

Anonymous

  • 490 Answers

SOURCE: Alarm will not shut off after battery replacement

find a good auto electric shop and have them remove or by-pass this mess.It can be done,I recomend it.

Posted on Aug 03, 2009

john h

  • 28545 Answers

SOURCE: I need to wire a 3 gang switches in a 3 gang box

before u start make sure power is off before working with electrical lines ---start with the 12/2 coming into box black [power] white [ground-neutral] and u will have 3 separate lines for the lights so u will have 4 lines total coming in the box== with the 3 light lines take the white and strip back the plastic and connect [wire nut] all 3 to the 12/2 white line --now take the 12/2 black line and connect it to the first switch gold color screw- bottom screw -now take some wire about 2-3 inch strip both ends and connect from the 12/2 black wire connection on the switch and connect to the gold /bottom of switch 2 than do the same for switch 3 connecting the wire from switch 2 so u will have power feeding all 3 switches-- now connect the black lines for the lights to the other side of each switch and ur done

Posted on Feb 14, 2010

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
2answers

No power in back bedroom

Locate your circuit panel, and check your fuses/circuit breakers.
Maybe breaker tripped?
To reset, remember: All the way to OFF position first, then flip towards ON.
0helpful
1answer

How do i set arlec pc 899 powerpoint time ??

Q1. How to set on / off times?
A1. Shift the red actuator pin to the desired on time
shift the black actuator pin to the desired off time.
Q2. What is the shortest time interval?
A2. 15 minutes.
Q3. Maximum switching times?
A3. One "on" and one "off" setting.
Q4. Can you override?
A4. Yes, use the override switch.

Note: If the main power is turned off the timer will need to be reset.

To set the timer to the current time you will need to turn the dial in a clockwise direction until the smaller arrow (Line) on the front face is pointing to the current time.

Regards,
Arlec Customer Service
+61 3 9982 5111
0helpful
1answer

Why is the GFCI outlet getting power, but still not working?

GFCI's have 4 terminals. 2 marked Load, 2 marked Line. The black and white wires from the power supply MUST be connected to the LINE terminals. The load terminals is where you connect the outgoing circuit (i.e. plug, light etc). Anything connected to the load terminals will be controlled by the GFCI, so when it trips everything on that circuit will go off until you rest it. The other light/switch cannot be connected to the GFI if you want the switch to control it separately.
0helpful
1answer

Timer wont turn on

Add a comment and include timer brand and model, or describe timer in detail.
Is timer plugged into outlet? Or harwired?
Does outlet have power?
Is circuit breaker ON?
Is this new timer, or old timer that stopped working?
Reset timer.
Change battery?
What load is being controlled by timer?

If you need further help, I’m available over the phone at https://www.6ya.com/expert/gene_9f0ef4df2f9897e7

0helpful
1answer

Sylvania 730SVD flat screen with built in dvd... Can't eject dvd inside and when turned on the digital words show up and keep flashing black gray green red... The remote won't even work..

Try resetting the TV by disconnecting it from the mains outlet for 1/2 hour, then connect to the main outlet and switch on the TV.
0helpful
1answer

No power to microwave

Hello

Check the Power Cord

Verify that the power cord is properly connected the outlet; the plug might have been removed to make way for another appliance. Do not connect the microwave to an outlet via an extension cord or plug adapter; the oven must be directly connected to an outlet.
Switch the Outlet on

Turn the outlet on, if possible, using the switch on the wall behind the counter or on the plug itself. Some microwaves have a separate power switch that must be in the correct position before you can begin cooking.
Reset the Oven

Unplug the oven, wait a few seconds and reconnect the power. A power surge could have temporarily rendered the oven inoperable. The oven should start up as normal when you connect the plug to the outlet.
Check the Fuses and Breakers

See that the fuse or breaker protecting the oven's circuit is still active. Replace the fuse if it has blown, or reset the breaker to restore power to the oven. Stop using the microwave if it repeatedly blows fuses or trips breakers.
0helpful
1answer

I must reprogram my tv each time I turn it on

I'm assuming that you are powering the TV off with the remote, not by shutting off a device (such as a home theater system that it is plugged into) and having it disconnect the power from the cord. if this is how it is shut off, that will be your problem.

Likewise, you may have plugged the TV into an outlet that is operated by a wall switch. These are typically found in rooms that do not have an overhead light, and are designed to control a table lamp. Usually, the receptacle will have one outlet that is on all the time, and the other controlled by a wall switch. Check to make sure that the outlet that the TV is plugged into remains on all the time - regardless of the position of any wall switches.

The solution to both of the above issues is to plug the TV into an outlet that is on all the time. The interruption of household power to the TV is most likely causing the memory loss of the settings in the TV.

The other possibility may be the way you are shutting off the TV each night. Some TVs have an on / off function that works with the remote, but only if the standby power is on. If the standby power is off, the remote will not be able turn the TV on. Some manufacturers use different colored indicating lamps for Off, Standby On and TV On.

Without knowing your brand and model TV, I can't go deeper than that. You'll need to consult your TV manual to see if and how your TV works - or provide the brand and model info so we can see if we can find a solution if none of the above works for you. I hope this helps & good luck.
1helpful
2answers

I don't know the model code

Hello

You are a technician and you whats to know the model service code I thinks, and posts this solution.

Use the Remote Commander (RM-Y183, RM-Y184) to perform the circuit adjustments in this section

SETTING THE SERVICE ADJUSTMENT
MODE

1. Standby mode (Power off).

2. Press the following buttons on the remote commander within one

second of each other:
DISPLAY Channel 5 Sound Volume + Power

READING THE MEMORY

1. Enter into service mode.

2. Press 0 on the remote commander.
3. Press ENTER to read memory.

ADJUSTING THE PICTURE

1. Enter into service mode

2. Press 2 or 5 on the remote to select the device item.

3. Press 1 or 4 on the remote to select an item.

4. Press 3 or 6 on the remote to change the data.


RESETTING THE DATA

Note: Be careful when using the remote! It will clear and re-initialize

ALL NVM data including defl ection adjustment data if not reset
properly as follows:
5. Press MUTING then ENTER to write into memory.

RESETTING THE DEFLECTION NVM DATA

1. Enter into service mode.

2. Press 7 , then MENU, and then press ENTER on the remote.

RESETTING THE SYSTEM NVM DATA

1. Enter into service mode.

2. Press 7 , then 9 , and then press ENTER on the remote.

RESETTING THE SYSTEM NVM DATA

1. Enter into service mode.
2. Press 8 and then press ENTER on the remote.

MEMORY WRITE CONFIRMATION

METHOD

1. After adjustment, pull out the plug from the AC outlet, then replace the

plug in the AC outlet again.

2. Turn the power switch ON and set to Service Mode.
3. Call the adjusted items again to confi rm they were adjusted.
Ok.

0helpful
1answer

I have Whirlpool model #ACQ128XP0, there is NO power at all to it, breaker is not blown, fan will work in the same outlet, so it is not the electrical outlet, i turned it on the other day, and it made the...

I am not an expert but I have two of the remote controlled 8000 BTU units and one of the 12000 BTU units like this one.


I have found that the remote controlled Whirlpool units that used this type of electronics sometime had a problem with cold solder joints on the motor control board. This is the board that has the relays that control the fan speed and compressor. Check for cold solder joints on all connections that have large diameter wire. These connections apparently did not get hot enough to properly flow the solder on the large diameter wire.

3helpful
2answers

Electrical output requirement for a buit-in oven and cooktop

Providing the existing switch outlet iscontrolled by a 30amp circuit fuse or trip, then there is no problem connecting the 2 appliances to the same switch.
If on the other hand, it is controlled by a 13 amp breaker, then you cannot connect both appliances to this, you would have to use 2 seperate sockets.
Hope this clarifys your question.
Not finding what you are looking for?

Open Questions:

7,654 views

Ask a Question

Usually answered in minutes!

Top Power Computers & Internet Experts

vince

Level 3 Expert

1548 Answers

NADARK
NADARK

Level 2 Expert

79 Answers

Cindy Wells

Level 3 Expert

6589 Answers

Are you a Power Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...