Question about Leisure Pool & Spa

1 Answer

Garden leisure spa lights flash at bottom of controller.Pumps do not run.Fuses are good. What do flashung lights mean?

Posted by DAVID PRICE on


1 Answer

David Spradling

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.


    An expert that got 20 achievements.


    An expert that got 10 achievements.

  • Leisure Master
  • 11,272 Answers

Check recirculation pump and heater element

Posted on Oct 14, 2017


5 Related Answers

Joe Hogan

  • 10865 Answers

SOURCE: I have power to the spa, but it won't power up

there are at least two separate circuit breakers feeding your spa and two reset buttons. the circuit breakers are located a few feet away from the spa in an electrical box.

the reset buttons are in the mechanical space of the spa where the pump and heater are located.

Posted on Aug 17, 2009



  • 80 Answers

SOURCE: "Jacuzzi j-400 series" hot tub- F1 code flashes on control panel

There are two things you can check, there is a tranformer that plugs into the main circuit board(usually a four wire plug). Unplug and check pins for good connection and then reconnect There are usually one or two fuses inside the control box mounted on or near the circuit board. Turn off power to spa and pull fuses and check continunity. This is a good start.

Posted on Aug 19, 2009

A Miller

  • 8404 Answers

SOURCE: Need manual for Leisure Bay spa

Go here and click on Spa Manuals.

Posted on May 16, 2010


Steve Nordquist

  • 981 Answers

SOURCE: Where can i find the Schematics for this

Leisure Bay Spas' engineering department.

Posted on May 18, 2010


US Parts Center

  • 719 Answers

SOURCE: leisure bay spa series c,

What light is blinking? The heater light? Because the heater light will not come on until the spa goes through the purge cycle when the breaker is first turned on.Exactly what is happening once the breaker is turned on

Posted on Feb 11, 2011

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I have a Leisure Bay hot tub but cannot figure out how to drain it. Number D2 1874

should be a garden hose down at bottom either exposed or remove front panel by controls or pump out with simer or cover pump

Mar 25, 2018 | Leisure Pool & Spa

1 Answer

My Intex spa is reading error code 90. We have put new filters on cleaned it all.

Take a look here...
Intex HongKong Limited Service Center


UK TEL: 0333 400 45 48 FAX: 01480 414761 WEBSITE: EMAIL: [email protected]

Apr 22, 2015 | Intex Pool & Spa

1 Answer

Dont know what the name of my leisure bay hot tub is model number on pump says spo7211nca

Okay, those numbers mean nothing, and it's just pertaining to a electric motor that is attached to a wet end, which makes up a pump.
what is your question for this forum, if you are seeking assistance? Do you have a problem with this spa?

Apr 07, 2015 | Leisure Pool & Spa

1 Answer

Circutboard trace break for garden leisure hot tub

check the timer and thermostat settings also the heater contacts see if they need cleaned(shut off or unplug before servicing..severe shock hazard!!!)

Dec 14, 2013 | Pool & Spa

1 Answer

Garden leisure spa

check to make sure you are getting 220 to it if not the check breacker

Sep 07, 2013 | Pool & Spa

1 Answer

Spa pumps makes alot of noise when set on low. Sounds better when set on high, but will lock up when switching between the two. Garden leisure spa.

Either have the motor rebuilt or replace it. At some point in time you had a pump seal leak which lead to the berrings going out. If you replace the motor be sure to replace the seal as well.

Aug 01, 2013 | Pool & Spa

1 Answer

Need a capacitor for my Aqua Leisure 2150GPH pump.

If there is a motor repair shop in your area, go there. They will be able to get you one or offer a good substitute. Good luck...Lee

Nov 13, 2009 | Aqua Leisure 2,150 GPH Filter Pump

2 Answers

"Jacuzzi j-400 series" hot tub- F1 code flashes on control panel

Your circulation pump isn't working you should see the flow awitch closing if you have the visible model and hear the pump running.. If its the smaller circulation pump model it needs replacing

May 18, 2009 | Jacuzzi Bath Nova H530 917 Black Soaking...

Not finding what you are looking for?
Pool & Spa Logo

Related Topics:

125 people viewed this question

Ask a Question

Usually answered in minutes!

Top Leisure Pool & Spa Experts


Level 3 Expert

5724 Answers


Level 3 Expert

35295 Answers

Steve Slater

Level 2 Expert

72 Answers

Are you a Leisure Pool and Spa Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides