Question about Pride Health & Beauty

1 Answer

What dose red or yellow blinking lights on my jazzy pride electric power chair mean /

Posted by PETE BARTEAU on

Ad

1 Answer

Ernest

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 434 Answers

  1. VR2/VSI DIAGNOSTIC FLASH CODES
# OF LEDS
CODE
CAUSE
POSSIBLE SOLUTION
One red LED
1
Low battery voltage
Charge batteries
Two red LEDs
2
Left motor open
Make sure left motor is plugged into controller.
Three red LEDs
3
Left motor wiring fault
Contact your authorized Pride Provider.
Three red LEDs One yellow LED
4
Right motor open
Make sure right motor is plugged into controller.
Three red LEDs Two yellow LEDs
5
Right motor wiring fault
Contact your authorized Pride Provider.
Three red LEDs Three yellow LEDs
6
Inhibit active
Contact your authorized Pride Provider.
Three red LEDs Four yellow LEDs
7
Joystick error
Contact your authorized Pride Provider.
Three red LEDs Four yellow LEDs One green LED
8
Controller error
Contact your authorized Pride Provider.
Three red LEDs Four yellow LEDs Two green LEDs
9
Brake fault
Make sure both motors are plugged into controller.
Three red LEDs Four yellow LEDs Three green LEDs
10
High battery voltage
Contact your authorized Pride Provider.
What if the speed LEDs on the VR2/VSI begin to flash?

  • Determine if the battery charger is connected to the power base. When the battery charger is connected to the power base, a charger inhibit feature keeps the power chair from driving. This is indicated by the VR2/VSI speed
    LED(s) flashing.
  • Determine if the charger harness fuse has blown. A blown charger fuse can cause the charger inhibit to
    activate.
  • Determine if all controller connections are plugged into the power base properly. If the 3-pin charger
    inhibit connector is not plugged in properly, then the charger inhibit feature will activate.

Posted on Oct 05, 2017

Ad

5 Related Answers

williamhobbs

  • 16 Answers

SOURCE: power chair lights

The problem was a bad joystick. A local company came out to replace it and it works fine now.

Posted on Mar 07, 2009

Ad

Anonymous

  • 29 Answers

SOURCE: pride mobility Jet 3 Ultra Power Chair 7 flashing

a 7 Flashe code. There is a joystick fault. Make sure the joystick is in the center position and then power off and on again. Check all your couplings. make sure when turning on the unit you only mash the power button for 1 sec. 2-3 sec will put the unit in "Lock out mode".
This ierror will also be present if the joystick is off center when powered up. If you experience these symptoms, you must first make sure there is no physical damage to the joystick preventing it from returning to the center position. Then turn the power off and back on again (making sure the joystick is not depressed in any direction. If the joystick repeats this error, the controler much be replaced. [email protected]

Posted on Sep 07, 2009

Barry Nixon

  • 103 Answers

SOURCE: Jazzy wheel chair

When a chair sits for a long period of time ( four weeks or more) without being charged, the batteries die. To help you with the freewheel mode I would have to know what model of Jazzy it is.

Posted on Nov 16, 2009

HoverTech

Donna Angelo

  • 232 Answers

SOURCE: chair no longer charges, no flashing or blinking, lights,

The number of lights that are blinking indicate what the problem is. Visit this site to locate the type on controller on your power chair and you will be able to see that the blinking lights mean:
http://www.pgdt.com/scenter/diagnostics/diagvsi.html
Try to reset your manual brake release as this is a common problem.
If you continue to have a problem, contact your manufacturer or dealer for service. If your insurance purchased they power chair for you, they may also cover the cost of repairs.
Good luck!

Posted on Oct 20, 2010

TIM MANNING

  • 50 Answers

SOURCE: Our Jazzy Select G.T. power

Hi
delobner,

Sometime we lock our vsi joystick by mistake. Here are the instructions on how to lock and unlock your joystick.

If the problem is still there after write me back and I'll help you.

LOCKING/UNLOCKING THE VSI

The VSI has a feature that enables you to lock your power chair to prevent

unauthorized use.

To lock the VSI:

1. With the VSI powered on, press and hold the on/off key. After one (1)

second, the VSI should beep.

2. Release the on/off key.

3. Push the joystick to the full forward position until the VSI beeps.

4. Pull the joystick to the full rearward position until the VSI beeps.

5. Release the joystick. There should be a long beep.

6. The VSI is now locked.

To unlock the VSI:

1. Press the on/off key and power on the VSI. The maximum speed/profile
indicator should ripple side to side.

Good Luck
mi mobility

Posted on May 05, 2011

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How can I get this chair to work


Pride Mobility Products Download the trouble shooting information for your model chair.

Aug 29, 2016 | Pride New Jazzy 600 Power Wheelchair by...

1 Answer

What does it mean on 1122 jazzy when the two red lights blink


JAZZY 1122 - Pride Mobility Products

www.pridemobility.com/...manuals/...jazzy/.../au_jazzy_1...
Pride MobilityJAZZY 1122. How a Power Chair Should ... NOTE: This owner's manual is compiled from the latest specifications and product information available at the time of .

Jul 31, 2015 | Pride Mobility Jazzy 1122 Electric...

1 Answer

Jazzy chair 600 3 red lights 4 yellow 1 green no power both batteries read 12.5


Have the joystick controller tested. Make sure the cable is fully seated in the chair connector.

Feb 17, 2014 | Pride Jazzy 1113 ATS Indoor Power...

1 Answer

Jazzy 1133 has new batteries. All lights are lit on the battery condition meter. Maximum speed/profile indicator constantly blinks no matter how many sements are lit. After I turn it off and waiting a...


If all lights are flashing excessive voltage has been applied to the controller system. 6 flashing lights on the 1133 indicates that the chair is being inhibited by the battery charger. Try unplugging the battery charger. Check you battery connections.

Mar 30, 2013 | Pride Jazzy 1113 Power Chair

1 Answer

Blinking yellow wrench light on pride jazzy 614 HD


Your version has a Dynamic Controls model controller and joystick.
Unplug the charger and engage the motor/brake lever so the chair is no longer in free-wheel mode (con't push by hand)
Turn the chair off, wait 5 seconds, turn the chair back.
If chair still does not run and your wrench is flashing you have a problem. Count the wrench flashes - the flash count indicates the error detected. 3, 4, 5, and 6 flashes indicate and error with the motors.
3=Left motor fault
4=Right motor fault
5=Left brake fault (may not be engaged)
6=Right brake fault (may not be engaged)
Any other fault code usually means the electronics or wiring is bad and not worth fixing.

Jan 06, 2013 | Pride Jazzy 614 Hd JAZZY 614HD

1 Answer

I JUST PURCHASED A JAZZY WHEEL CHAIR AND IT IS I THINK 2003 MODEL WHEN TURNED ON THERE ARE 3 RED LIGHTS AND 4 YELLOW LIGHTS FLASHING AND NOTHING HAPPENS


the 7 lights indicate a joystick problem which means the joystick/controller will have to be replaced since there is no self repair fix Unless you can locate a good used joystick/controller for cheap (around $600.00 rebuilt) I would return the chair and get my money back Hope this helps

Jun 20, 2011 | Pride Jazzy 1103 Ultra Standard Power...

1 Answer

I took the Jazzy outside over a hump and unlocked the yellow leavers and now it won't start again. The lights just blink and then they go off......Help


Do you mean the freewheel levers?
The chair will not drive if you have it in freewheel. Push the levers back in, and then turn the chair off and on. It should be working now.

Feb 20, 2011 | Pride Jazzy 1103 Ultra Standard Power...

1 Answer

Wont move yellow lights ,flashing


The number of lights that are blinking indicate what the problem is. Visit this site to locate the type on controller on your power chair and you will be able to see that the blinking lights mean:
http://www.pgdt.com/scenter/diagnostics/diagvsi.html
Try to reset your manual brake release as this is a common problem.
If you continue to have a problem, contact your manufacturer or dealer for service. If your insurance purchased they power chair for you, they may also cover the cost of repairs.
Good luck!

Sep 10, 2010 | Pride Jazzy 1103 Ultra Standard Power...

1 Answer

Chair no longer charges, no flashing or blinking, lights,


The number of lights that are blinking indicate what the problem is. Visit this site to locate the type on controller on your power chair and you will be able to see that the blinking lights mean:
http://www.pgdt.com/scenter/diagnostics/diagvsi.html
Try to reset your manual brake release as this is a common problem.
If you continue to have a problem, contact your manufacturer or dealer for service. If your insurance purchased they power chair for you, they may also cover the cost of repairs.
Good luck!

May 07, 2010 | Pride Jazzy 1103 Ultra Standard Power...

Not finding what you are looking for?
Health & Beauty Logo

Related Topics:

447 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pride Health & Beauty Experts

Rob Hill
Rob Hill

Level 3 Expert

1414 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Mike

Level 3 Expert

4372 Answers

Are you a Pride Health and Beauty Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...