I am wondering if there is a contact number where I can get some serious help using my godox v860 with my sony a 7rii. I am new to flash and it is like a foreign language.

The issue you are experiencing with your Godox X1 trigger and TT350 flash not firing when mounted on your Olympus E-M10 camera, could be related to the camera's settings or the compatibility of the trigger and flash with your camera. Here are a few things you can try:

1. Make sure the trigger and flash are set to the correct channel and group: The trigger and flash should be set to the same channel and group in order for them to communicate properly.
2. Check the camera's flash settings: Make sure that the camera's flash mode is set to "Wireless" or "Off-Camera" and that the flash is set to "Manual" or "TTL" mode.
3. Check for firmware updates: Make sure that the trigger and flash have the latest firmware installed. This can be done through the Godox website or by using the Godox firmware update tool.
4. Check the camera's hot shoe: Make sure that the camera's hot shoe is clean and free of debris. Also, check that the trigger and flash are properly connected to the hot shoe.
5. Check the camera's manual: Make sure that the camera is compatible with the trigger and flash. Some cameras may have different settings or limitations that affect the use of external flashes.

If none of the above steps resolve the issue, it may be best to contact Godox customer support for further assistance. They will be able to diagnose and fix the issue or tell you if a repair is needed.
It's also important to note that some cameras have a "pre-flash" that might not be compatible with some triggers, in this case, you should use the manual flash mode to avoid this problem.

Sound very much like a camera to transmitter problem. Make sure the transmitter is properly seated on a cleaned hotshoe. Make sure the Godox is compatible is with the 5Div

If you still have the 12V car adapter it ships with, you can buy a 12V supply with a cigarette lighter connector and use that .

You could try contacting their main distributor who lists the complete device :http://www.lightinthebox.com/godox-pb820-backup-external-battery-pack-for-speedlite-vsp-136265_p995394.html , but does not list the charger alone.

Failing the distributor, try contacting the factory. They offer direct contact for support ([email protected]),including skype chat ([email protected] for MSN/skype).

Adorama sells the "Flashpoint" series of devices which seem to be relabeled versions of Godox products, but only sell the 960 larger power pack not the 820.

I read that the 820 DIN cable connector is compatible with Quantum cables. That *might* mean that one of the Quantum chargers *might* work for you, as those use a DIN connector for some of the rechargeable Quantum batteries. I once adapted a wall adapter for charging a Quantum battery pack and used a DIN connector. Unfortunately the Quantum chargers are expensive and there are a number of different models,so it may be difficult to figure out what will work for yo.

Hi Anonymous,

For this situations the best is to get in touch with our Support team, so they can re-flash your device. You can find the contact information here:
http://bit.ly/ContactUs-Locate

Regards,
Gaby
Motorola Mobility

Master Reset Motorola Barrage V860

Mark
Motorola Support

Same problem. I cannot load my PB820. I know it is not a problem of battery because I tested them. I know it is not a problem of charger (very easy to test, pin 2+ and 5- on the plug). So it is a problem with the electronic.
I am waiting for an answer of Godox.
I cannot find any electronic description of the electronic part - it would be very easy to change any part - but cannot do it blind...

Get a Nikon AS-15.
Then run a PC Sync Cable from camera to light.

The capacitor (neck) is no longer hold a charge or charging circuit is going out on a extended breaks.

Save your money and buy ATG's Godox TT685c.
If you buys two, then you got ATG wireless radio ETTL II flashes.
It would cost over $1,000.00+ USD to buy two Canon 600EX II-RT just to do the same with two ATG's.

Hi,
Pioneer CLD-V860 is an old model laser disc player and you need to have service manual copy to get error code details as we do not have related service manual copy.
Required service manual copy can be downloaded from HERE for small fee and service manual has all technical info about this unit, schematics, troubleshooting chart, part numbers etc.
Hope this info will help you.
Thanks.

This is something that I really would not recommend doing unless you are sure what you are doing as this can seriously harm the computer. The best suggestion is to contact the sony help online and send them your product number and serial number then they know what flash bios you have and can send you a link to the correct download. Through experience when I tried to do a flash bios upgrade my computer went dead until I opened the back and had to shock the dumb thing.